[Why]
Visual confirm will indicate if driver is programming
the surface address.
Refactor is required because much of the visual confirm
logic is buried deep in the mpcc files.
In addition, visual confirm is not updated during fast updates.

[How]
In order to have visual confirm for driver flips, visual confirm
needs to be updated on every frame, including fast updates.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.

v2: drop unused variable (Alex)
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
As per spec, DCN3.x can do 6:1 downscaling and DCN2.x can do 4:1. The
max downscaling limit value for DCN2.x is 250, which means it's
calculated as 1000 / 4 = 250. For DCN3.x this then gives 1000 / 6 = 167.

[how]
Set maximum downscaling limit to 167 for DCN3.x
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
amdgpu_dm_crtc_set_crc_source() will call
amdgpu_dm_crtc_configure_crc_source() to enable/disable CRC
generation. However, configuration will be deferred to stream enabled.
If stream is not enabled, current flow will still try to get/put vblank
refcount.

[How]
Return EINVAL to skip actions on vblank refcount when stream is not
enabled.
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Reviewed-by: NChao-kai Wang <Stylon.Wang@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
eDP version and DPCD revision are different. Per VESA
spec, "The DPCD revision for eDP v1.4 is 13h".

SUPPORTED_LINK_RATES is valid since eDP v1.4 (DPCD_REV_13).

[How]
Correct DPCD_REV for eDP v1.4.
Signed-off-by: NZhan Liu <zhan.liu@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In some small modes (<200pixels) the stutter period is really big and will cause
overflow. In these cases we shouldnt try to enable MALL as it will exceeds range
of hysteresis timer (this can be seen in some IGT tests where the
plane size is small)

[How]
Compare the stutter_period with the frame time and if we will overflow
there is no point in trying to enable MALL (and see the ASSERT) so we
early exist in this case
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Once set ROI and do suspend/resume, current flow will not enable
OTG_CRC_CTL again due to we'll defer crc configuration when stream
is enabled.

[How]
Remove current suspend/resume function and have logic implemented into
amdgpu_dm_atomic_commit_tail()
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Reviewed-by: NChao-kai Wang <Stylon.Wang@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Some lttpr configuration steps are exclusive to 8b/10b channel
coding mode. We need to take channel conding into account.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NGeorge Shen <George.Shen@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Acked-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
The function's name doesn't represent what it actaully does.
The function implements necessary steps for our hardware to
transition from link training mode back to video idle mode.
Therefore, rename the function as dp_transition_to_video_idle
so everyone can understand it.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NGeorge Shen <George.Shen@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[how]
Rename initialize_training_settings to decide_training_settings.
Call get link encoding format and decide training settings
based on current channel coding.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NGeorge Shen <George.Shen@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[how]
Implement a function that determines link encoding format
based on the link settings passed in.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NGeorge Shen <George.Shen@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Active DP dongles return no EDID when dongle
is connected, but VGA display is taken out.
Current driver behavior does not remove the
active display when this happens, and this is
a gap between dongle DTP and dongle behavior.

[How]
For active DP dongles and non-DP scenario,
disconnect sink on detection when no EDID
is read due to timeout.
Signed-off-by: NChris Park <Chris.Park@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Improve readability and maintainability of code.

[How]
Refactor test pattern size calculation out of function
call parameter and store value in variable.
Signed-off-by: NGeorge Shen <george.shen@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

During the investigation on how to add visual confirmation on top of the
planes used by DCN, it becomes evident that the lack of information in
the code makes this work unnecessarily complicated. This commit
introduces a set of documentation related to the RECOUT operation in
order to make it easy for developers to navigate this set of functions.
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

To improve the code readability, this commit removes a set of commented
and not used functions for a long time. Notice that now we have the
amdgpu_dm_dtn_log, which prints all the relevant information that we
need.
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This commit introduces kernel documentation to some essential functions
related to power gate control over planes. It also adds a macro to make
one part of the code easy to understand.
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Need to get current DMUB time.

[How]
Add get_current_time interface to dmub_srv.

v2: drop whitespace changes (Alex)
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Previous patch caused crash and had been reverted. This patch
addresses the issue without regression.

[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.

[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Signed-off-by: NHugo Hu <hugo.hu@amd.com>
Reviewed-by: NSung Lee <Sung.Lee@amd.com>
Acked-by: NStylon Wang <stylon.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When determinism mode is disabled on aldebaran, max GFX clock will
be reset to default max frequency value.
Signed-off-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NKevin Wang <kevin1.wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v1: Use the current and custom pstate frequencies to track the current and
user-set min/max values in manual and determinism mode. Previously, only
actual_* value was used to track the currrent and user requested value.
The value will get reassigned whenever user requests a new value with
pp_od_clk_voltage node. Hence it will show incorrect values when user
requests an invalid value or tries a partial request without committing
the values. Separating out to custom and current variable fixes such
issues.

v2: Remove redundant if-else check
Signed-off-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NKevin Wang <kevin1.wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add custom member for user requested custom frequency, level mask
or min/max frequencies. Add curr member to keep track of the current
active values.
Signed-off-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NKevin Wang <kevin1.wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Only clear RAS error counters if perestent EDC harvesting is not supported
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There is problem with 3DCGCG firmware and it will cause compute test
hang on picasso/raven1. It needs to disable 3DCGCG in driver to avoid
compute hang.
Signed-off-by: NChangfeng <Changfeng.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

there are 2 hubs to flush in the gmc, to make it easier
to debug when hub flush failed, refine the logs.
Signed-off-by: NPeng Ju Zhou <PengJu.Zhou@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

KMD should not the program these registers,
so skip them in the SRIOV environment.
Signed-off-by: NPeng Ju Zhou <PengJu.Zhou@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When PAGE_SIZE is larger than AMDGPU_PAGE_SIZE, the number of GPU TLB
entries which need to update in amdgpu_map_buffer() should be multiplied
by AMDGPU_GPU_PAGES_IN_CPU_PAGE (PAGE_SIZE / AMDGPU_PAGE_SIZE).
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NYi Li <liyi@loongson.cn>
Signed-off-by: NHuacai Chen <chenhuacai@loongson.cn>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Need do a heavy-weight TLB flush to make sure we have no more dirty data
in the cache for the unmapped pages.

Define enum TLB_FLUSH_TYPE, add flush_type parameter to
amdgpu_amdkfd_flush_gpu_tlb_pasid.
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit 1704ac8e.

After "drm/amdgpu: flush TLB if valid PDE turns into PTE" is checked
in, this workaround is not needed.
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Initialize unique_id from PF2VF under virtualization.

V2: skip smu_get_unique_id() under virtualization
Signed-off-by: NJiawei Gu <Jiawei.Gu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Mapping huge page, 2MB aligned address with 2MB size, uses PDE0 as PTE.
If previously valid PDE0, PDE0.V=1 and PDE0.P=0 turns into PTE, this
requires TLB flush, otherwise page table walker will not read updated
PDE0.

Change page table update mapping to return table_freed flag to indicate
the previously valid PDE may have turned into a PTE if page table is
freed.
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Imported BOs don't have a pagelist any more.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Fixes: 0575ff3d ("drm/radeon: stop using pages with drm_prime_sg_to_page_addr_arrays v2")

Not used outside of that file.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Tested-by: NNirmoy Das <nirmoy.das@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Drop the last user of drm_mm_node.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Tested-by: NNirmoy Das <nirmoy.das@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This avoids reallocating scanout BOs on first pin in a lot of cases.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Tested-by: NNirmoy Das <nirmoy.das@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

One of the last remaining uses of drm_mm_node.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Tested-by: NNirmoy Das <nirmoy.das@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Now that we found the underlying problem we can re-apply this patch.

This reverts commit 6b44b667.

v2: rebase on KFD changes
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Tested-by: NNirmoy Das <nirmoy.das@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Only send boot_config cmd to ASICs that support dynamic
boot config. Otherwise, the boot_config cmd will fail.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Check firmware flags to determine whether dynmaic
boot config is supported or not.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Check cached firmware_flags to determin whether
two stage mem training is supported or not.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Check cached firmware_flags to determine whether
sram ecc is supported or not.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>