I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch addes the BenQ 3g modem support to the option driver.


From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- New Novatel and Dell mobile broadband modem products added
 - Dell pid variables used in stead of numerical PIDs for known
   products
Signed-off-by: NDirk De Schepper <ddeschepper@nvtl.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Revert 8b6346ec as these devices really
work just fine with the cdc-acm driver, as they follow the spec
properly.

Thanks to Chuck Ebbert for pointing out the problem here.

Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the support  for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: NAlex Cheng <alex.cheng@quantatw.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).

This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: NMarcel Sebek <sebek64@post.cz>
Acked-by: NDomenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This should speed up the option driver's upload speed quite a bit.  It has been tested by a number of different people on different devices with success.

Cc: Roland Wolters <roland.wolters@credativ.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some of the usb-serial drivers are starting to use urb->status in ways
they should not be doing.  This fixes up some of them to prevent that.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Thanks to Domenico Riccio for pointing these out.

Cc: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds YISO u893 usb modem vendor and product ID to option.c.

I had a better experience using this modification and the same system.
Signed-off-by: NLeslie Harlley Watter <leslie@watter.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support  more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.

To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero.  In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices.  But in this new solution, it can
be compatible with all of our data card devices.
Signed-off-by: Nfangxiaozhi <huananhu@huawei.com>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMikhail Gusarov <dottedmag@dottedmag.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add some Pantech mobile broadband IDs.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The AnyData ADU-310 series of wireless modems uses the same product ID as the ADU-E100 series.
Signed-off-by: NJon K Hellan <hellan@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove duplicate device ids which are now supported by drivers/usb/net/hso.c
Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a few more mobile broadband cards.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.

Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch  support  NTT DoCoMo A2502 3G/HSDPA modem on option driver.
It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW.

It support 3.6Mbps/7.2Mbps hight speed communication.
I have tested A2502 with NTT DoCoMo MoperaU ISP service.
Signed-off-by: NHiroshi Miura <miurahr@nttdata.co.jp>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These drivers should not be relying on CONFIG_USB_DEBUG.  By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.

Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: NOliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the Product ID for the BandLuxe C150/C250 3.5G data
card series from BandRich Inc.
After detection, the data card works fine.

It was patched against kernel 2.6.27-rc1 with -mm patch
Signed-off-by: NLeon Leong <upleong@bandrich.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.

So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.

Longer term we need a proper tty as console abstraction
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver is only for one device id, and the option driver should be
used instead for it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Thanks to umesh b <umesh.kollam@gmail.com> for the information here.

Cc: umesh b <umesh.kollam@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the interface info matching to all Huawei cards, as they all also
contain a Mass Storage Device interface (usually containing Windows
drivers) which should not get bound by this driver.

See also drivers/usb/storage/unusual_devs.h
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes the name of the onda MSA501HS device, I guess it is called
different things in different countries.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the Telit UC864-E HDSPA modem support to the option driver.
This lets their customers comply with the GPL instead of having to use a
binary driver from the manufacturer.

Cc: Simon Kissel <kissel@viprinet.com>
Cc: Nico Erfurth <ne@nicoerfurth.de>
Cc: Andrea Ghezzo <TS-EMEA@telit.com>
Cc: Dietmar Staps <Dietmar.Staps@telit.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

New variant of the 5520 found by Luke Sheldrick.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This device is not a serial port, but a virtual CD-ROM device. For
example with my Novatel MC950D:

lsusb -v -d 1410:5010 | grep InterfaceClass
      bInterfaceClass         8 Mass Storage

After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:

% lsusb -v -d 1410:4400 | grep InterfaceClass
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceClass       255 Vendor Specific Class

Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Signed-off-by: NEugeniy Meshcheryakov <eugen@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Signed-off-by: NMauro Andreolini <andreoli@weblab.ing.unimo.it>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported by Magnus Boman <captain.magnus@opensuse.org>

Cc: Magnus Boman <captain.magnus@opensuse.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

urb->context code cleanup
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 - If a termios change fails due to lack of memory we should copy the
   old settings back over as the device has not changed
 - Note various locking problems
 - kl5kusb105 had various remaining tty flag handling problems
 - Make safe_serial use tty_insert_flip_string not open coded loops
 - set termios speed properly in usb_serial
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb-serial core no longer checks these fields so remove them from
all of the individual drivers.  They will be removed from the usb-serial
core in a patch later in the series.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Setting DTR et al. should work for all interfaces
if you actually pass the interface number. :-P
 
This should help with devices that have important pseudo-serial ports
that aren't on the first interface in the device.
Signed-off-by: NChris Collins <chris@ursys.com.au>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>