This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core.  Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering.  This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core.  With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.

On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore.  On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds code to allow us to use a different value for the HFSCR
(Hypervisor Facilities Status and Control Register) when running the
guest from that which applies in the host.  The reason for doing this
is to allow us to trap the msgsndp instruction and related operations
in future so that they can be virtualized.  We also save the value of
HFSCR when a hypervisor facility unavailable interrupt occurs, because
the high byte of HFSCR indicates which facility the guest attempted to
access.

We save and restore the host value on guest entry/exit because some
bits of it affect host userspace execution.

We only do all this on POWER9, not on POWER8, because we are not
intending to virtualize any of the facilities controlled by HFSCR on
POWER8.  In particular, the HFSCR bit that controls execution of
msgsndp and related operations does not exist on POWER8.  The HFSCR
doesn't exist at all on POWER7.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

It is possible, through a narrow race condition, for a VCPU to exit
the guest with a H_CEDE hypercall while it has a doorbell interrupt
pending.  In this case, the H_CEDE should return immediately, but in
fact it puts the VCPU to sleep until some other interrupt becomes
pending or a prod is received (via another VCPU doing H_PROD).

This fixes it by checking the DPDES (Directed Privileged Doorbell
Exception Status) bit for the thread along with the other interrupt
pending bits.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This allows userspace (e.g. QEMU) to enable large decrementer mode for
the guest when running on a POWER9 host, by setting the LPCR_LD bit in
the guest LPCR value.  With this, the guest exit code saves 64 bits of
the guest DEC value on exit.  Other places that use the guest DEC
value check the LPCR_LD bit in the guest LPCR value, and if it is set,
omit the 32-bit sign extension that would otherwise be done.

This doesn't change the DEC emulation used by PR KVM because PR KVM
is not supported on POWER9 yet.

This is partly based on an earlier patch by Oliver O'Halloran.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

POWER9 DD1 has an erratum where writing to the TBU40 register, which
is used to apply an offset to the timebase, can cause the timebase to
lose counts.  This results in the timebase on some CPUs getting out of
sync with other CPUs, which then results in misbehaviour of the
timekeeping code.

To work around the problem, we make KVM ignore the timebase offset for
all guests on POWER9 DD1 machines.  This means that live migration
cannot be supported on POWER9 DD1 machines.

Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

At present, HV KVM on POWER8 and POWER9 machines loses any instruction
or data breakpoint set in the host whenever a guest is run.
Instruction breakpoints are currently only used by xmon, but ptrace
and the perf_event subsystem can set data breakpoints as well as xmon.

To fix this, we save the host values of the debug registers (CIABR,
DAWR and DAWRX) before entering the guest and restore them on exit.
To provide space to save them in the stack frame, we expand the stack
frame allocated by kvmppc_hv_entry() from 112 to 144 bytes.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

If userspace attempts to call the KVM_RUN ioctl when it has hardware
transactional memory (HTM) enabled, the values that it has put in the
HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by
guest values.  To fix this, we detect this condition and save those
SPR values in the thread struct, and disable HTM for the task.  If
userspace goes to access those SPRs or the HTM facility in future,
a TM-unavailable interrupt will occur and the handler will reload
those SPRs and re-enable HTM.

If userspace has started a transaction and suspended it, we would
currently lose the transactional state in the guest entry path and
would almost certainly get a "TM Bad Thing" interrupt, which would
cause the host to crash.  To avoid this, we detect this case and
return from the KVM_RUN ioctl with an EINVAL error, with the KVM
exit reason set to KVM_EXIT_FAIL_ENTRY.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This restores several special-purpose registers (SPRs) to sane values
on guest exit that were missed before.

TAR and VRSAVE are readable and writable by userspace, and we need to
save and restore them to prevent the guest from potentially affecting
userspace execution (not that TAR or VRSAVE are used by any known
program that run uses the KVM_RUN ioctl).  We save/restore these
in kvmppc_vcpu_run_hv() rather than on every guest entry/exit.

FSCR affects userspace execution in that it can prohibit access to
certain facilities by userspace.  We restore it to the normal value
for the task on exit from the KVM_RUN ioctl.

IAMR is normally 0, and is restored to 0 on guest exit.  However,
with a radix host on POWER9, it is set to a value that prevents the
kernel from executing user-accessible memory.  On POWER9, we save
IAMR on guest entry and restore it on guest exit to the saved value
rather than 0.  On POWER8 we continue to set it to 0 on guest exit.

PSPB is normally 0.  We restore it to 0 on guest exit to prevent
userspace taking advantage of the guest having set it non-zero
(which would allow userspace to set its SMT priority to high).

UAMOR is normally 0.  We restore it to 0 on guest exit to prevent
the AMR from being used as a covert channel between userspace
processes, since the AMR is not context-switched at present.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds code to save the values of three SPRs (special-purpose
registers) used by userspace to control event-based branches (EBBs),
which are essentially interrupts that get delivered directly to
userspace.  These registers are loaded up with guest values when
entering the guest, and their values are saved when exiting the
guest, but we were not saving the host values and restoring them
before going back to userspace.

On POWER8 this would only affect userspace programs which explicitly
request the use of EBBs and also use the KVM_RUN ioctl, since the
only source of EBBs on POWER8 is the PMU, and there is an explicit
enable bit in the PMU registers (and those PMU registers do get
properly context-switched between host and guest).  On POWER9 there
is provision for externally-generated EBBs, and these are not subject
to the control in the PMU registers.

Since these registers only affect userspace, we can save them when
we first come in from userspace and restore them before returning to
userspace, rather than saving/restoring the host values on every
guest entry/exit.  Similarly, we don't need to worry about their
values on offline secondary threads since they execute in the context
of the idle task, which never executes in userspace.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

POWER9 introduces a new mode for the decrementer register, called
large decrementer mode, in which the decrementer counter is 56 bits
wide rather than 32, and reads are sign-extended rather than
zero-extended.  For the decrementer, this new mode is optional and
controlled by a bit in the LPCR.  The hypervisor decrementer (HDEC)
is 56 bits wide on POWER9 and has no mode control.

Since KVM code reads and writes the decrementer and hypervisor
decrementer registers in a few places, it needs to be aware of the
need to treat the decrementer value as a 64-bit quantity, and only do
a 32-bit sign extension when large decrementer mode is not in effect.
Similarly, the HDEC should always be treated as a 64-bit quantity on
POWER9.  We define a new EXTEND_HDEC macro to encapsulate the feature
test for POWER9 and the sign extension.

To enable the sign extension to be removed in large decrementer mode,
we test the LPCR_LD bit in the host LPCR image stored in the struct
kvm for the guest.  If is set then large decrementer mode is enabled
and the sign extension should be skipped.

This is partly based on an earlier patch by Oliver O'Halloran.

Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.

Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.

As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.

Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.

As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.

Fixes: 4027494a ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: NRussell King <linux@armlinux.org.uk>
Reported-by: NOmar Sandoval <osandov@osandov.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NRob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on
an address. What this means in practice is that it should only return true for
addresses in the linear mapping which are backed by a valid PFN.

We are failing to properly check that the address is in the linear mapping,
because virt_to_pfn() will return a valid looking PFN for more or less any
address. That bug is actually caused by __pa(), used in virt_to_pfn().

eg: __pa(0xc000000000010000) = 0x10000  # Good
    __pa(0xd000000000010000) = 0x10000  # Bad!
    __pa(0x0000000000010000) = 0x10000  # Bad!

This started happening after commit bdbc29c1 ("powerpc: Work around gcc
miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition
of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from
the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give
you something bogus back.

Until we can verify if that GCC bug is no longer an issue, or come up with
another solution, this commit does the minimal fix to make virt_addr_valid()
work, by explicitly checking that the address is in the linear mapping region.

Fixes: bdbc29c1 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Tested-by: NBreno Leitao <breno.leitao@gmail.com>

The page table dump code doesn't know about huge pages, so currently
it crashes (or walks random memory, usually leading to a crash), if it
finds a huge page. On Book3S we only see huge pages in the Linux page
tables when we're using the P9 Radix MMU.

Teaching the code to properly handle huge pages is a bit more involved,
so for now just prevent the crash.

Cc: stable@vger.kernel.org # v4.10+
Fixes: 8eb07b18 ("powerpc/mm: Dump linux pagetables")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 22d8b3de ("powerpc/kprobes: Emulate instructions on kprobe
handler re-entry") enabled emulating instructions on kprobe re-entry,
rather than single-stepping always. However, we didn't update the single
stepping code to only be run if the emulation fails. Also, we missed
re-enabling preemption if the instruction emulation was successful. Fix
those issues.

Fixes: 22d8b3de ("powerpc/kprobes: Emulate instructions on kprobe handler re-entry")
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 17ed4c8f ("powerpc/powernv: Recover correct PACA on wakeup
from a stop on P9 DD1") promises to set the NAPSTATELOST bit in paca
after recovering the correct paca for the thread waking up from stop1
on DD1, so that the GPRs can be correctly restored on the stop exit
path. However, it loads the value 1 into r3, but stores the value in
r0 into NAPSTATELOST(r13).

Fix this by correctly set the NAPSTATELOST bit in paca after
recovering the paca on POWER9 DD1.

Fixes: 17ed4c8f ("powerpc/powernv: Recover correct PACA on wakeup from a stop on P9 DD1")
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In commit dc310669 ("powerpc: tm: Always use fp_state and vr_state
to store live registers"), a section of code was removed that copied
the current state to checkpointed state. That code should not have been
removed.

When an FP (Floating Point) unavailable is taken inside a transaction,
we need to abort the transaction. This is because at the time of the
tbegin, the FP state is bogus so the state stored in the checkpointed
registers is incorrect. To fix this, we treclaim (to get the
checkpointed GPRs) and then copy the thread_struct FP live state into
the checkpointed state. We then trecheckpoint so that the FP state is
correctly restored into the CPU.

The copying of the FP registers from live to checkpointed is what was
missing.

This simplifies the logic slightly from the original patch.
tm_reclaim_thread() will now always write the checkpointed FP
state. Either the checkpointed FP state will be written as part of
the actual treclaim (in tm.S), or it'll be a copy of the live
state. Which one we use is based on MSR[FP] from userspace.

Similarly for VMX.

Fixes: dc310669 ("powerpc: tm: Always use fp_state and vr_state to store live registers")
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: cyrilbur@gmail.com
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On powerpc we can build the kernel with two different ABIs for mcount(), which
is used by ftrace. Kernels built with one ABI do not know how to load modules
built with the other ABI. The new style ABI is called "mprofile-kernel", for
want of a better name.

Currently if we build a module using the old style ABI, and the kernel with
mprofile-kernel, when we load the module we'll oops something like:

  # insmod autofs4-no-mprofile-kernel.ko
  ftrace-powerpc: Unexpected instruction f8810028 around bl _mcount
  ------------[ cut here ]------------
  WARNING: CPU: 6 PID: 3759 at ../kernel/trace/ftrace.c:2024 ftrace_bug+0x2b8/0x3c0
  CPU: 6 PID: 3759 Comm: insmod Not tainted 4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74 #11
  ...
  NIP [c0000000001eaa48] ftrace_bug+0x2b8/0x3c0
  LR [c0000000001eaff8] ftrace_process_locs+0x4a8/0x590
  Call Trace:
    alloc_pages_current+0xc4/0x1d0 (unreliable)
    ftrace_process_locs+0x4a8/0x590
    load_module+0x1c8c/0x28f0
    SyS_finit_module+0x110/0x140
    system_call+0x38/0xfc
  ...
  ftrace failed to modify
  [<d000000002a31024>] 0xd000000002a31024
   actual:   35:65:00:48

We can avoid this by including in the vermagic whether the kernel/module was
built with mprofile-kernel. Which results in:

  # insmod autofs4-pg.ko
  autofs4: version magic
  '4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74 SMP mod_unload modversions '
  should be
  '4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74-dirty SMP mod_unload modversions mprofile-kernel'
  insmod: ERROR: could not insert module autofs4-pg.ko: Invalid module format

Fixes: 8c50b72a ("powerpc/ftrace: Add Kconfig & Make glue for mprofile-kernel")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Acked-by: NJessica Yu <jeyu@redhat.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit e91aa8e6 ("KVM: PPC: Enable IOMMU_API for KVM_BOOK3S_64
permanently", 2017-03-22) enabled the SPAPR TCE code for all 64-bit
Book 3S kernel configurations in order to simplify the code and
reduce #ifdefs.  However, 64-bit Book 3S PPC platforms other than
pseries and powernv don't implement the necessary IOMMU callbacks,
leading to build failures like the following (for a pasemi config):

scripts/kconfig/conf  --silentoldconfig Kconfig
warning: (KVM_BOOK3S_64) selects SPAPR_TCE_IOMMU which has unmet direct dependencies (IOMMU_SUPPORT && (PPC_POWERNV || PPC_PSERIES))

...

  CC [M]  arch/powerpc/kvm/book3s_64_vio.o
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_64_vio.c: In function ‘kvmppc_clear_tce’:
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_64_vio.c:363:2: error: implicit declaration of function ‘iommu_tce_xchg’ [-Werror=implicit-function-declaration]
  iommu_tce_xchg(tbl, entry, &hpa, &dir);
  ^

To fix this, we make the inclusion of the SPAPR TCE support, and the
code that uses it in book3s_vio.c and book3s_vio_hv.c, depend on
the inclusion of support for the pseries and/or powernv platforms.
This means that when running a 'pseries' guest on those platforms,
the guest won't have in-kernel acceleration of the PAPR TCE hypercalls,
but at least now they compile.
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The PR KVM implementation of the PAPR HPT hypercalls (H_ENTER etc.)
access an image of the HPT in userspace memory using copy_from_user
and copy_to_user.  Recently, the declarations of those functions were
annotated to indicate that the return value must be checked.  Since
this code doesn't currently check the return value, this causes
compile warnings like the ones shown below, and since on PPC the
default is to compile arch/powerpc with -Werror, this causes the
build to fail.

To fix this, we check the return values, and if non-zero, fail the
hypercall being processed with a H_FUNCTION error return value.
There is really no good error return value to use since PAPR didn't
envisage the possibility that the hypervisor may not be able to access
the guest's HPT, and H_FUNCTION (function not supported) seems as
good as any.

The typical compile warnings look like this:

  CC      arch/powerpc/kvm/book3s_pr_papr.o
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c: In function ‘kvmppc_h_pr_enter’:
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c:53:2: error: ignoring return value of ‘copy_from_user’, declared with attribute warn_unused_result [-Werror=unused-result]
  copy_from_user(pteg, (void __user *)pteg_addr, sizeof(pteg));
  ^
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c:74:2: error: ignoring return value of ‘copy_to_user’, declared with attribute warn_unused_result [-Werror=unused-result]
  copy_to_user((void __user *)pteg_addr, hpte, HPTE_SIZE);
  ^

... etc.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

POWER9 running a radix guest will take some hypervisor interrupts
without going to real mode (turning off the MMU).  This means that
early hypercall handlers may now be called in virtual mode.  Most of
the handlers work just fine in both modes, but there are some that
can crash the host if called in virtual mode, notably the TCE (IOMMU)
hypercalls H_PUT_TCE, H_STUFF_TCE and H_PUT_TCE_INDIRECT.  These
already have both a real-mode and a virtual-mode version, so we
arrange for the real-mode version to return H_TOO_HARD for radix
guests, which will result in the virtual-mode version being called.

The other hypercall which is sensitive to the MMU mode is H_RANDOM.
It doesn't have a virtual-mode version, so this adds code to enable
it to be called in either mode.

An alternative solution was considered which would refuse to call any
of the early hypercall handlers when doing a virtual-mode exit from a
radix guest.  However, the XICS-on-XIVE code depends on the XICS
hypercalls being handled early even for virtual-mode exits, because
the handlers need to be called before the XIVE vCPU state has been
pulled off the hardware.  Therefore that solution would have become
quite invasive and complicated, and was rejected in favour of the
simpler, though less elegant, solution presented here.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Tested-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Regularly, when a new header is created in include/uapi/, the developer
forgets to add it in the corresponding Kbuild file. This error is usually
detected after the release is out.

In fact, all headers under uapi directories should be exported, thus it's
useless to have an exhaustive list.

After this patch, the following files, which were not exported, are now
exported (with make headers_install_all):
asm-arc/kvm_para.h
asm-arc/ucontext.h
asm-blackfin/shmparam.h
asm-blackfin/ucontext.h
asm-c6x/shmparam.h
asm-c6x/ucontext.h
asm-cris/kvm_para.h
asm-h8300/shmparam.h
asm-h8300/ucontext.h
asm-hexagon/shmparam.h
asm-m32r/kvm_para.h
asm-m68k/kvm_para.h
asm-m68k/shmparam.h
asm-metag/kvm_para.h
asm-metag/shmparam.h
asm-metag/ucontext.h
asm-mips/hwcap.h
asm-mips/reg.h
asm-mips/ucontext.h
asm-nios2/kvm_para.h
asm-nios2/ucontext.h
asm-openrisc/shmparam.h
asm-parisc/kvm_para.h
asm-powerpc/perf_regs.h
asm-sh/kvm_para.h
asm-sh/ucontext.h
asm-tile/shmparam.h
asm-unicore32/shmparam.h
asm-unicore32/ucontext.h
asm-x86/hwcap2.h
asm-xtensa/kvm_para.h
drm/armada_drm.h
drm/etnaviv_drm.h
drm/vgem_drm.h
linux/aspeed-lpc-ctrl.h
linux/auto_dev-ioctl.h
linux/bcache.h
linux/btrfs_tree.h
linux/can/vxcan.h
linux/cifs/cifs_mount.h
linux/coresight-stm.h
linux/cryptouser.h
linux/fsmap.h
linux/genwqe/genwqe_card.h
linux/hash_info.h
linux/kcm.h
linux/kcov.h
linux/kfd_ioctl.h
linux/lightnvm.h
linux/module.h
linux/nbd-netlink.h
linux/nilfs2_api.h
linux/nilfs2_ondisk.h
linux/nsfs.h
linux/pr.h
linux/qrtr.h
linux/rpmsg.h
linux/sched/types.h
linux/sed-opal.h
linux/smc.h
linux/smc_diag.h
linux/stm.h
linux/switchtec_ioctl.h
linux/vfio_ccw.h
linux/wil6210_uapi.h
rdma/bnxt_re-abi.h

Note that I have removed from this list the files which are generated in every
exported directories (like .install or .install.cmd).

Thanks to Julien Floret <julien.floret@6wind.com> for the tip to get all
subdirs with a pure makefile command.

For the record, note that exported files for asm directories are a mix of
files listed by:
 - include/uapi/asm-generic/Kbuild.asm;
 - arch/<arch>/include/uapi/asm/Kbuild;
 - arch/<arch>/include/asm/Kbuild.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Acked-by: NMark Salter <msalter@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The ibm,powerpc-cpu-features device tree binding describes CPU features with
ASCII names and extensible compatibility, privilege, and enablement metadata
that allows improved flexibility and compatibility with new hardware.

The interface is described in detail in ibm,powerpc-cpu-features.txt in this
patch.

Currently this code is not enabled by default, and there are no released
firmwares that provide the binding.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently we assume that if the cpu_spec has a pvr_mask then it must also have a
cpu_name. But that will change in a subsequent commit when we do CPU feature
discovery via the device tree, so check explicitly if cpu_name is NULL.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Similarly to commit 2563a70c ("powerpc/64s: Remove unnecessary relocation
branch from idle handler"), the machine check handler has a BRANCH_TO from
relocated to relocated code, which is unnecessary.

It has also caused build errors with some toolchains:

  arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
  arch/powerpc/kernel/exceptions-64s.S:395: Error: operand out of range
  (0xffffffffffff8280 is not between 0x0000000000000000 and
  0x000000000000ffff)

Fixes: 1945bc45 ("powerpc/64s: Fix POWER9 machine check handler from stop state")
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Reported-and-tested-by : Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Recently in commit f6eedbba ("powerpc/mm/hash: Increase VA range to 128TB")
we increased the virtual address space for user processes to 128TB by default,
and up to 512TB if user space opts in.

This obviously required expanding the range of the Linux page tables. For Book3s
64-bit using hash and with PAGE_SIZE=64K, we increased the PGD to 2^15 entries.
This meant we could cover the full address range, while still being able to
insert a 16G hugepage at the PGD level and a 16M hugepage in the PMD.

The downside of that geometry is that it uses a lot of memory for the PGD, and
in particular makes the PGD a 4-page allocation, which means it's much more
likely to fail under memory pressure.

Instead we can make the PMD larger, so that a single PUD entry maps 16G,
allowing the 16G hugepages to sit at that level in the tree. We're then able to
split the remaining bits between the PUG and PGD. We make the PGD slightly
larger as that results in lower memory usage for typical programs.

When THP is enabled the PMD actually doubles in size, to 2^11 entries, or 2^14
bytes, which is large but still < PAGE_SIZE.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

Makefile.postlink always includes include/config/auto.conf, however
this file is not present in a clean kernel tree, causing make to fail:

  $ git clone linuxppc.git
  $ cd linuxppc.git
  $ make distclean
  arch/powerpc/Makefile.postlink:10: include/config/auto.conf: No such file or directory
  make[1]: *** No rule to make target `include/config/auto.conf'.  Stop.
  make: *** [vmlinuxclean] Error 2

Equally running 'make distclean; make distclean' will trip the error case.

Change the inclusion such that file not being found does not trigger an error.

Fixes: f188d052 ("powerpc: Use the new post-link pass to check relocations")
Reported-by: NMircea Pop <mircea.pop@nxp.com>
Signed-off-by: NHoria Geantă <horia.geanta@nxp.com>
Tested-by: NJustin M. Forbes <jforbes@fedoraproject.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This typo is quite common.  Fix it and add it to the spelling file so
that checkpatch catches it earlier.

Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.orgSigned-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fadump supports specifying memory to reserve for fadump's crash kernel
with fadump_reserve_mem kernel parameter.  This parameter currently
supports passing a fixed memory size, like fadump_reserve_mem=<size>
only.  This patch aims to add support for other syntaxes like
range-based memory size
<range1>:<size1>[,<range2>:<size2>,<range3>:<size3>,...] which allows
using the same parameter to boot the kernel with different system RAM
sizes.

As crashkernel parameter already supports the above mentioned syntaxes,
this patch deprecates fadump_reserve_mem parameter and reuses
crashkernel parameter instead, to specify memory for fadump's crash
kernel memory reservation as well.  If any offset is provided in
crashkernel parameter, it will be ignored in case of fadump, as fadump
reserves memory at end of RAM.

Advantages using crashkernel parameter instead of fadump_reserve_mem
parameter are one less kernel parameter overall, code reuse and support
for multiple syntaxes to specify memory.
Suggested-by: NDave Young <dyoung@redhat.com>
Link: http://lkml.kernel.org/r/149035346749.6881.911095631212975718.stgit@hbathini.in.ibm.comSigned-off-by: NHari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that crashkernel parameter parsing and vmcoreinfo related code is
moved under CONFIG_CRASH_CORE instead of CONFIG_KEXEC_CORE, remove
dependency with CONFIG_KEXEC for CONFIG_FA_DUMP.  While here, get rid of
definitions of fadump_append_elf_note() & fadump_final_note() functions
to reuse similar functions compiled under CONFIG_CRASH_CORE.

Link: http://lkml.kernel.org/r/149035343956.6881.1536459326017709354.stgit@hbathini.in.ibm.comSigned-off-by: NHari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit f4ea6dcb ("powerpc/mm: Enable mappings above 128TB") increased
the task size on book3s, and introduced a mechanism to dynamically
control whether a task uses these larger addresses.  While the change to
the task size itself was ifdef-protected to only apply on book3s, the
change to STACK_TOP_USER64 was not.  On book3e, this had the effect of
trying to use addresses up to 128TiB for the stack despite a 64TiB task
size limit -- which broke 64-bit userspace producing the following errors:

Starting init: /sbin/init exists but couldn't execute it (error -14)
Starting init: /bin/sh exists but couldn't execute it (error -14)
Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance.

Fixes: f4ea6dcb ("powerpc/mm: Enable mappings above 128TB")
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Similar to what is done in commit b6541db1 ("powerpc/eeh: Block
PCI config access upon frozen PE"), we need block PCI config access
for BCM5719 when recovering frozen error on them. Otherwise, an
unexpected recursive fenced PHB error is observed.

   0001:06:00.0 Ethernet controller: Broadcom Corporation \
                NetXtreme BCM5718 Gigabit Ethernet PCIe (rev 10)
   0001:06:00.1 Ethernet controller: Broadcom Corporation \
                NetXtreme BCM5718 Gigabit Ethernet PCIe (rev 10)
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Power9/ISAv3 has no VRMASD field in LPCR, we shouldn't be setting reserved bits,
so don't set them on Power9.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 616badd2 ("powerpc/powernv: Use OPAL call for TCE kill on
NVLink2") forced all TCE kills to go via the OPAL call for
NVLink2. However the PHB3 implementation of TCE kill was still being
called directly from some functions which in some circumstances caused
a machine check.

This patch adds an equivalent IODA2 version of the function which uses
the correct invalidation method depending on PHB model and changes all
external callers to use it instead.

Fixes: 616badd2 ("powerpc/powernv: Use OPAL call for TCE kill on NVLink2")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently the radix TLB code includes support for CPUs that do *not*
have MMU_FTR_LOCKLESS_TLBIE. On those CPUs we are required to take a
global spinlock before issuing a tlbie.

Radix can only be built for 64-bit Book3s CPUs, and of those, only
POWER4, 970, Cell and PA6T do not have MMU_FTR_LOCKLESS_TLBIE. Although
it's possible to build a kernel with Radix support that can also boot on
those CPUs, we happen to know that in reality none of those CPUs support
the Radix MMU, so the code can never actually run on those CPUs.

So remove the native_tlbie_lock in the Radix TLB code.

Note that there is another lock of the same name in the hash code, which
is unaffected by this patch.
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

machine_check_early() gets called in real mode. The very first time when
add_taint() is called, it prints a warning which ends up calling opal
call (that uses OPAL_CALL wrapper) for writing it to console. If we get a
very first machine check while we are in opal we are doomed. OPAL_CALL
overwrites the PACASAVEDMSR in r13 and in this case when we are done with
MCE handling the original opal call will use this new MSR on it's way
back to opal_return. This usually leads to unexpected behaviour or the
kernel to panic. Instead move the add_taint() call later in the virtual
mode where it is safe to call.

This is broken with current FW level. We got lucky so far for not getting
very first MCE hit while in OPAL. But easily reproducible on Mambo.

Fixes: 27ea2c42 ("powerpc: Set the correct kernel taint on machine check errors.")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The entire body of unregister_cpu_online() is inside an #ifdef
CONFIG_HOTPLUG_CPU block. This is ugly and means we create an empty function
when hotplug is disabled for no reason.

Instead move the #ifdef out of the function body and define the function to be
NULL in the else case. This means we'll pass NULL to cpuhp_setup_state(), but
that's fine because it accepts NULL to mean there is no teardown callback, which
is exactly what we want.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This code was until recently completely undocumented and even now the comment is
not very verbose.

We've already had one patch sent to remove the IRQ enable/disable because it's
"paradoxical and unnecessary". So document it thoroughly to save anyone else
from puzzling over it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Otherwise we might select it when its dependenices aren't enabled,
leading to a build break.

It's default y anyway, so will be on unless someone disables it
manually.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

pnv_eeh_reset() has special handling for PEs whose primary bus is the
root bus or the bus immediately underneath the root port.

The cxl bi-modal card support added in b0b5e591 ("cxl: Add
cxl_check_and_switch_mode() API to switch bi-modal cards") relies on
this behaviour when hot-resetting the CAPI adapter following a mode
switch.  Document this in pnv_eeh_reset() so we don't accidentally break
it.
Suggested-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch allows the use of IRQ to notify the change of GPIO status
on MPC8xx CPM IO ports. This then allows to associate IRQs to GPIOs
in the Device Tree.

Ex:
	CPM1_PIO_C: gpio-controller@960 {
		#gpio-cells = <2>;
		compatible = "fsl,cpm1-pario-bank-c";
		reg = <0x960 0x10>;
		fsl,cpm1-gpio-irq-mask = <0x0fff>;
		interrupts = <1 2 6 9 10 11 14 15 23 24 26 31>;
		interrupt-parent = <&CPM_PIC>;
		gpio-controller;
	};

The property 'fsl,cpm1-gpio-irq-mask' defines which of the 16 GPIOs
have the associated interrupts defined in the 'interrupts' property.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NScott Wood <oss@buserror.net>