Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mac driver support for evaluation board based on w90p910.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel has used a stale email address of Andreas for a few years.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver received an EEM packet with CRC option enabled, driver must
compute and check the CRC of the Ethernet data. Previous version computes CRC
on Ethernet data plus the original CRC value. Skbuff is correctly trimed but
the old length is used when CRC is computed.
Signed-off-by: NVincent CUISSARD <vincent.cuissard@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit changes to shutdown path broke startup on some systems.

revert commit c0bad0f2Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.

This have to be converted to use coherent memory for the descriptors.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding device forbids slave device of different types under the same
master.

However, it is possible for a bonding master to change type during its
lifetime.  This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND
or the other way arround.  The change of type requires device level
multicast address cleanup because device level multicast addresses
depend on the device type.

The patch adds a call to dev_close() before the bonding master changes
type and dev_open() just after that.

In the example below I enslaved an IPoIB device (ib0) under
bond0. Since each bonding master starts as device of type ARPHRD_ETHER
by default, a change of type occurs when ib0 is enslaved.

This is how /proc/net/dev_mcast looks like without the patch

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     01005e000116
5    bond0           1     0     01005e7ffffd
5    bond0           1     0     01005e000001
5    bond0           1     0     333300000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     333300000001
6    ib0             1     0     01005e000001
6    ib0             1     0     01005e7ffffd
6    ib0             1     0     01005e000116
6    ib0             1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff00000000000000000001

and this is how it looks like after the patch.

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     00ffffffff12601bffff00000000000000000001
5    bond0           1     0     00ffffffff12401bffff0000000000000ffffffd
5    bond0           1     0     00ffffffff12401bffff00000000000000000116
5    bond0           1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     00ffffffff12401bffff00000000000000000116
6    ib0             1     0     00ffffffff12401bffff0000000000000ffffffd
6    ib0             2     0     00ffffffff12401bffff00000000000000000001
6    ib0             2     0     00ffffffff12601bffff00000000000000000001
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix misplaced parenthesis
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parentheses are required or the comparison occurs before the bitand.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit adeab1af.

As Alan Cox explained, the TTY layer changes that went recently
to get rid of the tty->low_latency stuff fixes this already,
and even for -stable it's the ->low_latency changes that should
go in to fix this, rather than this patch.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

spin_unlock_irq() will enable interrupt in net_send_packet(),
this patch changes it to spin_lock_irqsave/spin_lock_irqrestore,
so that it doesn't enable interrupts when already disabled,
and netconsole would work properly over cs89x0/isa-skeleton.

Call trace:
netconsole write_msg()
{
 ...
 -> spin_lock_irqsave();
        -> netpoll_send_udp()
          -> netpoll_send_skb()
            -> net_send_packet()
              ->...

 -> spin_unlock_irqrestore();
 ...
}
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't forget to unlock a mutex in phy_scan_fixups on a fail path.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

forward declaration of inline function should be avoided, or
old gcc cannot compile.
Reported-by: NTeck Choon Giam <giamteckchoon@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix duplicate testing of MCAST flag
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJay Cliburn <jcliburn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Guido Trentalancia reports:

I am trying to use the kiss driver in the Linux kernel that is being
shipped with Fedora 10 but unfortunately I get the following oops:

mkiss: AX.25 Multikiss, Hans Albas PE1AYX
mkiss: ax0: crc mode is auto.
ADDRCONF(NETDEV_CHANGE): ax0: link becomes ready
------------[ cut here ]------------
WARNING: at kernel/softirq.c:77 __local_bh_disable+0x2f/0x83() (Not
tainted)
[...]
unloaded: microcode]
Pid: 0, comm: swapper Not tainted 2.6.27.25-170.2.72.fc10.i686 #1
 [<c042ddfb>] warn_on_slowpath+0x65/0x8b
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c04228b4>] ? __enqueue_entity+0xe3/0xeb
 [<c042431e>] ? enqueue_entity+0x203/0x20b
 [<c0424361>] ? enqueue_task_fair+0x3b/0x3f
 [<c041f88c>] ? resched_task+0x3a/0x6e
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
 [<c043255b>] __local_bh_disable+0x2f/0x83
 [<c04325ba>] local_bh_disable+0xb/0xd
 [<c06ab4e2>] _spin_lock_bh+0xb/0x16
 [<f8b6f600>] mkiss_receive_buf+0x2fb/0x3a6 [mkiss]
 [<c0572a30>] flush_to_ldisc+0xf7/0x198
 [<c0572b12>] tty_flip_buffer_push+0x41/0x51
 [<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
 [<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
 [<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
 [<c05ea290>] uhci_giveback_urb+0xe5/0x15f
 [<c05eaabf>] uhci_scan_schedule+0x52e/0x767
 [<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
 [<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
 [<c05ec5b0>] uhci_irq+0x110/0x125
 [<c05d4834>] usb_hcd_irq+0x40/0xa3
 [<c0465313>] handle_IRQ_event+0x2f/0x64
 [<c046642b>] handle_level_irq+0x74/0xbe
 [<c04663b7>] ? handle_level_irq+0x0/0xbe
 [<c0406e6e>] do_IRQ+0xc7/0xfe
 [<c0405668>] common_interrupt+0x28/0x30
 [<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
 [<c0617f52>] cpuidle_idle_call+0x60/0x92
 [<c0403c61>] cpu_idle+0x101/0x134
 [<c069b1ba>] rest_init+0x4e/0x50
 =======================
---[ end trace b7cc8076093467ad ]---
------------[ cut here ]------------
WARNING: at kernel/softirq.c:136 _local_bh_enable_ip+0x3d/0xc4()
[...]
Pid: 0, comm: swapper Tainted: G        W 2.6.27.25-170.2.72.fc10.i686
 [<c042ddfb>] warn_on_slowpath+0x65/0x8b
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c04228b4>] ? __enqueue_entity+0xe3/0xeb
 [<c042431e>] ? enqueue_entity+0x203/0x20b
 [<c0424361>] ? enqueue_task_fair+0x3b/0x3f
 [<c041f88c>] ? resched_task+0x3a/0x6e
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
 [<f8b6f642>] ? mkiss_receive_buf+0x33d/0x3a6 [mkiss]
 [<c04325f9>] _local_bh_enable_ip+0x3d/0xc4
 [<c0432688>] local_bh_enable_ip+0x8/0xa
 [<c06ab54d>] _spin_unlock_bh+0x11/0x13
 [<f8b6f642>] mkiss_receive_buf+0x33d/0x3a6 [mkiss]
 [<c0572a30>] flush_to_ldisc+0xf7/0x198
 [<c0572b12>] tty_flip_buffer_push+0x41/0x51
 [<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
 [<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
 [<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
 [<c05ea290>] uhci_giveback_urb+0xe5/0x15f
 [<c05eaabf>] uhci_scan_schedule+0x52e/0x767
 [<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
 [<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
 [<c05ec5b0>] uhci_irq+0x110/0x125
 [<c05d4834>] usb_hcd_irq+0x40/0xa3
 [<c0465313>] handle_IRQ_event+0x2f/0x64
 [<c046642b>] handle_level_irq+0x74/0xbe
 [<c04663b7>] ? handle_level_irq+0x0/0xbe
 [<c0406e6e>] do_IRQ+0xc7/0xfe
 [<c0405668>] common_interrupt+0x28/0x30
 [<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
 [<c0617f52>] cpuidle_idle_call+0x60/0x92
 [<c0403c61>] cpu_idle+0x101/0x134
 [<c069b1ba>] rest_init+0x4e/0x50
 =======================
---[ end trace b7cc8076093467ad ]---
mkiss: ax0: Trying crc-smack
mkiss: ax0: Trying crc-flexnet

The issue was, that the locking code in mkiss was assuming it was only
ever being called in process or bh context.  Fixed by converting the
involved locking code to use irq-safe locks.

Review of other networking line disciplines shows that 6pack, both sync
and async PPP and STRIP have similar issues.  The ppp_async one is the
most interesting one as it sorts out half of the issue as far back as
2004 in commit http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=2996d8deaeddd01820691a872550dc0cfba0c37dSigned-off-by: NRalf Baechle <ralf@linux-mips.org>
Reported-by: NGuido Trentalancia <guido@trentalancia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev() used to install default implementations of these
operations, but they must now be explicitly installed in struct
net_device_ops.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization.  For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port.  This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.

Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.

Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:

WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active

This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.

This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: NClyde McPherson <ccmcphe@verizon.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:

Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: NYevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"

It appears that this simple patch makes the device work perfectly.

This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: NPascal Terjan <pterjan@mandriva.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: NSteve Holland <sdh4@iastate.edu>
Signed-off-by: NJoe Chou <joe.chou@rdc.com.tw>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check that network interface is running before changing its MAC address.
Otherwise, rxch is accessed when it's NULL - causing a kernel oops.
Moreover, check that the new MAC address is valid.
Signed-off-by: NPablo Bitton <pablo.bitton@gmail.com>
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Tested-by: NChaithrika U S <chaithrika@ti.com>
[tested on DM6467 EVM]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb driver was defaulting to using the lock for pci-e function 0 for
all of the phys due to the fact that the lan id was not being set prior to
initialization.  This change makes it so that the function id is set prior
to checking for the phy id.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're missing a Kconfig help for the iwmc3200wifi driver.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we reclaim the tx desc, we always assume that the
last desc is a holding desc, which is not true, and skip it.
If the tx queue is drained during channel change, internal
reset and etc, the last descriptor may not be the holding
descriptor and we fail to reclaim them. This results in the
following two issues.

1. Tx stuck - We drop all the frames coming from upper layer
due to shortage in tx desc.

2. Crash - If we fail to reclaim a tx descriptor, we miss to
update the tx BA window with the seq number of the frame
associated to that desc, which, at some point, result in
the following crash due to an assert failure in ath_tx_addto_baw().

This patch fixes these two issues.

 kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180!
[155064.304164] invalid opcode: 0000 [#1] SMP
 Call Trace:
  [<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k]
  [<fbbc9591>]  ipv6? __ieee80211_tx+0x41/0x120 [mac80211]
  [<fbbcb5ae>] ?  aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211]
  [<c037e501>]  aes_generic? _spin_lock_irqsave+0x31/0x40
  [<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
  [<c03058b5>] ? __qdisc_run+0x1b5/0x200
  [<fbbcda5a>] ?  af_packetieee80211_select_queue+0xa/0x100 [mac80211]
  [<c02f53b7>] ?  i915dev_queue_xmit+0x2e7/0x3f0
  [<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211]
  [<c031bc35>] ? ip_output+0x55/0xb0
  [<c02e0188>] ? show_memcpy_count+0x18/0x60
  [<c02eb186>] ? __kfree_skb+0x36/0x90
  [<c02f2202>] ?  binfmt_miscdev_queue_xmit_nit+0xd2/0x110
  [<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
  [<c03058b5>] ? __qdisc_run+0x1b5/0x200
  [<c033bca7>] ?  scoarp_create+0x57/0x2a0
  [<c02f53b7>] ?  bridgedev_queue_xmit+0x2e7/0x3f0
  [<c03034a0>] ? eth_header+0x0/0xc0
  [<c033b95f>]  stp? arp_xmit+0x5f/0x70
  [<c033bf4f>] ? arp_send+0x5f/0x70
  [<c033c8f5>]  bnep? arp_solicit+0x105/0x210
  [<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390
  [<c013bf88>] ? run_timer_softirq+0x138/0x210
  [<c02fa410>] ?  ppdevneigh_timer_handler+0x0/0x390
  [<c02fa410>] ? neigh_timer_handler+0x0/0x390
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix condition in which radio LED did not initialize correctly, and remove
4 compilation warnings.

After the recent changes in rfkill, the radio LED used by b43/b43legacy
did not always initialize correctly.

Both b43 and b43legacy used the deprecated variable radio_enabled in
struct ieee80211_conf.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register

The ColdFire 5272 FEC driver has a different register address map
than other users of the FEC driver. And its definition of the
FEC_X_DES_ACTIVE register is incorrect, it should be 0x14.
The fec interface cannot transmit data with the old value.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
----
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a1091aae.

Fix NULL pointer dereference in tun_chr_pool() introduced by commit
33dccbb0 ("tun: Limit amount of queued
packets per device") and triggered by this code:

	int fd;
	struct pollfd pfd;
	fd = open("/dev/net/tun", O_RDWR);
	pfd.fd = fd;
	pfd.events = POLLIN | POLLOUT;
	poll(&pfd, 1, 0);
Reported-by: NEugene Kapun <abacabadabacaba@gmail.com>
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet a écrit :
> Ingo Molnar a écrit :
>>> The following changes since commit 52989765:
>>>   Linus Torvalds (1):
>>>         Merge git://git.kernel.org/.../davem/net-2.6

> >>> are available in the git repository at:

>>>   master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git master
>> Hm, something in this lot quickly wrecked networking here - see the
>> tx timeout dump below. It starts with:
>>
>> [  351.004596] WARNING: at net/sched/sch_generic.c:246 dev_watchdog+0x10b/0x19c()
>> [  351.011815] Hardware name: System Product Name
>> [  351.016220] NETDEV WATCHDOG: eth0 (forcedeth): transmit queue 0 timed out
>>
>> Config attached. Unfortunately i've got no time to do bisection
>> today.
>
>
>
> forcedeth might have a problem, in its netif_wake_queue() logic, but
> I could not see why a recent patch could make this problem visible now.
>
> CPU0/1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> is not a new cpu either :)
>
> forcedeth uses an internal tx_stop without appropriate barrier.
>
> Could you try following patch ?
>
> (random guess as I dont have much time right now)

We might have a race in napi_schedule(), leaving interrupts disabled forever.
I cannot test this patch, I dont have the hardware...
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The call resource_size(res) returns res->end - res->start + 1 and thus the
second change is semantics-preserving.  res_size is then used as the second
argument of a call to request_mem_region, and the memory allocated by this
call appears to be the same as what is released in the two calls to
release_mem_region.  So the size argument for those calls should be
resource_size(size) as well.  Alternatively, in the second call to
release_mem_region, the second argument could be res_size, as that variable
has already been initialized at the point of this call.

The problem was found using the following semantic patch:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct resource *res;
@@

- (res->end - res->start) + 1
+ resource_size(res)

@@
struct resource *res;
@@

- res->end - res->start
+ BAD(resource_size(res))
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>