Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.

Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.

While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no reason to pass mvm and trig as parameters to the macro,
since it will be expanded inside the function itself.  Also remove the
bogus buf parameter which doesn't exist and is not used.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.

Fixes: 9f9af3d7 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: NSharon Dvir <sharon.dvir@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fix the kernel-doc, and remove some fields even the firmware doesn't
use in ToF, RX, scan, station and generic FW APIS.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fix various "Excess struct/union/enum/typedef member '...' description
in '...'" warnings from kernel-doc, mostly caused by typos.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a debugfs entry to get a verbose description of the power settings
used in each band with the currently selected SAR geographic profile.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When trying to TX through a monitor interface, the
conditions in iwl_mvm_tx_skb_non_sta() don't match
and the frame tries to go out from an usued TXQ.

Add a check for monitor iface, and use the AUX queue
in such a case.

In non-DQA mode the frame is sent through the
static-allocated queues anyway, so the problem is
in DQA mode only.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

It's sometimes hard to find out which HW address the iwlwifi device is
using, for instance when reading crouded sniffer logs.  To make it
easier, print out an info level message with the HW address as soon as
we know it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Document the assoc_beacon_arrive_time element in the iwl_mac_data_sta
struct.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This new API allows flushing queues based on station ID and TID in A000
devices.  One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NMordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get an ASSERT, the fw_dump_desc pointer points to
iwl_mvm_dump_desc_assert which can't be freed since it is
a global. We still need to NULL'ify the pointer when we
call iwl_mvm_free_fw_dump_desc otherwise we will hit

int iwl_mvm_fw_dbg_collect_desc(struct iwl_mvm *mvm,
                                const struct iwl_mvm_dump_desc *desc,
                                const struct iwl_fw_dbg_trigger_tlv *trigger)
{
<snip>
        if (WARN_ON(mvm->fw_dump_desc))
                iwl_mvm_free_fw_dump_desc(mvm);

Fixes: b6eaa45a ("iwlwifi: mvm: add the cause of the firmware dump in the dump")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When updating the mac context after association,
assoc_beacon_arrive_time is not being set, which causes the FW to
set a wrong TSF to the MAC.

Fix this by setting the assoc_beacon_arrive_time when updating the
mac context after association.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.

In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.

This bug has been fixed on 9000 devices and up.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A TID may not have traffic but still have a BA agreement
active (or being setup / torn down) since a BA agreement
can be triggered by a debugfs hook.
Just avoid to consider such a TID as inactive to make the
logic safer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If the hardware is stuck, we can't read any of the memory we need to
dump it, so we end up printing only 0xa5a5a5a5, which is useless.

To solve this, poke the hardware by triggering a reset and re-enabling
the clocks if we detect a HW error.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In BSS mode in the disconnection flow, mac80211 removes
the AP station before the vif is set to unassociated.
Our firmware wants it the other way around: first set
the vif as unassociated, and then remove the AP station.

In order to bridge between those two different behaviors,
iwlmvm doesn't remove the station from the firmware when
mac80211 removes it, but only after the vif is set to
unassociated. The implementation is in
iwl_mvm_bss_info_changed_station:

if (assoc state was modified && mvmvif->ap_sta_id is VALID
    && assoc state is now UNASSC)
	remove_the_station_from_the_firmware()

During the recovery flow, mac80211 re-adds the AP station
and then reconfigures the vif. Since the vif is not
associated, and then, we enter the if above (which was
intended to be taken in the disconnection flow only) and
remove the station we just added. This defeats the
recovery flow.

Fix this by not removing the AP station in this flow if
we are in recovery flow.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We allocate nvm_data in iwl_mvm_nvm_get_from_fw().  If something goes
wrong after the allocation (i.e. if no valid MAC address is valid), we
should free nvm_data before returning an error.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This function just calls kfree(), so it only obscures the code without
bringing any benefits.  Remove it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add kernel-doc documentation for enum iwl_debug_cmds, linking the
structures used by the commands.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This improves documentation, since kernel-doc can't deal with the
union well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

To stop and start the FW monitor in the 7000 HW
family we need to use a different bit, otherwise
after stopping it for the first time - it won't
get restarted. Use the correct bitmask.

Note: This fix is only for DRAM collection mode.
      For other modes, an additional fix will be
      needed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fix the enum link by adding the missing & and provide the link
to the TX response documentation.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Show the name of the member (scanned_channels) that provides the
length with some better markup.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.

Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.

While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.

To make it fast, also trigger the waitq when on rfkill assert.

Fixes: 0636b938 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Some static checkers (e.g. smatch) complain about the logic, saying that
resp_cp might be leaked. Clearly that isn't true, but making the logic
easier to follow does not result in any significant code changes and makes
the code more readable by moving the NULL check closer to its source.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow.  If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow.  Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>