At the end of the boot process, the clock framework might disable
required main PLL's. So far, this was no issue since drivers
requested clocks, which are descended of the main PLL's (e.g.
pll1_pfd1, which provides the system clock).

To archive the full 500MHz system clock, DDR clock need to be a
descendant of PLL2 rather than PLL1 (DDRC_CLK_SEL set to 0). The
bootloader sets up the clocks accordingly before making use of
DDR at all. However, in Linux, there is no driver using PLL2,
which lead to PLL2 being disabled by the clock framework.

With this patch, we make sure that the main system clock and the
DDR clock are initially enabled and are kept enabled.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Extend the clock control for FlexCAN with the second gate which
enable the clocks in the Clock Divider (CCM_CSCDR2) register too.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch moves clock check function in common i.MX location
and switch i.MX clk drivers to use this new function.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

There should be no duplicate const specifiers for those static
constant character string arrays defined for clock mux options.
Also, the arrays are only taken as the 5th argument for the
imx_clk_mux() function, which is in the type of 'const char
**parents'.  So, let's remove the 2nd const specifier right
after 'char'.

This patch fixes these sparse warnings:
arch/arm/mach-imx/clk-vf610.c:66:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:67:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:68:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:69:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:70:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:71:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:72:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:73:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:74:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:75:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:76:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:77:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:78:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:79:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:80:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:81:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:83:25: warning: duplicate const
arch/arm/mach-imx/clk-vf610.c:84:25: warning: duplicate const
Signed-off-by: NLiu Ying <Ying.Liu@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The fec/enet driver calculates MDC rate with the formula below.

  ref_freq / ((MII_SPEED + 1) x 2)

The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now.  And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec.  This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz).  That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz.  And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.

  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half
  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half
  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half

Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.

Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>