Set bits 0, 4, 5 and 7 of PCI configuration register 0x40 in the
quirk.  This has the following effects and is recommended by the
vendor.

* Force enable of IDE channels (used to be left alone as BIOS
  configured)

* Change initial phase behavior of PIO cycle such that the host pulls
  down the bus instead of tristating it.  Vendor recommends this
  setting.

The above settings are better for the current generation of
controllers and needed for the upcoming next generation.

Tested on JMB363.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.

This patch sets the korrect register bit to enable the onboard sound.

Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.

New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: NJohannes Goecke <goecke@upb.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: Peter Oruba <peter.oruba@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Linas reported me that some machines were crashing at boot in
quirk_e100_interrupt. It appears that this quirk is doing an ioremap
directly on a PCI BAR value, which isn't legal and will cause all sorts
of bad things to happen on architectures where PCI BARs don't directly
match processor bus addresses.

This fixes it by using the proper PCI resources instead which is possible
since the quirk has been moved by a previous commit to happen late enough
for that.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: NGreg White <gw.kernel@tnode.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The k8t_sound_hostbridge PCI quick fires on my motherboard (Jetway
K8M8MS) while it shouldn't: the on-board sound chip is not disabled
and is working just fine. Looking at the code, I see that we are
running the quirk for two distinct register values (0x88 and 0xc8)
and then clear bit 6 (0x40). However value 0x88 already has bit 6
cleared so this is a no-op. This is what happens on my board. Thus I
believe that the quirk should only be run for register value 0xc8.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

RX790 can't do MSI like its predecessors.  Disable MSI on RX790.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

RD580 can't do MSI like its predecessors.  Disable MSI on RD580.
Signed-off-by: NTejun Heo <teheo@suse.de>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

RS690 can't do MSI like its predecessors.  Disable MSI on RS690.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Henry Su <henry.su@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

quirk_e100_interrupts() is called after PCI controller is initialized
and before PCI bus enumeration is performed. On some powerpc platforms
which modify PCI controller configuration and set different MEM and IO
windows than those set by firmware quirk_e100_interrupt() is causing
kernel panic as it tries to read from device BAR0 offets which at this
time points to a invalid PCI window (set by firmware).

This patch delays the quirk_100_interrupt() to pci_fixup_final phase,
which happens after bus enumeration and before PCI enable and
device driver initialization.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- remove unneeded local

- 80-col fix

Cc: Peter Oruba <peter.oruba@amd.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch introduces an interface to read and write PCI-X / PCI-Express 
maximum read byte count values from PCI config space. There is a second 
function that returns the maximum _designed_ read byte count, which marks the 
maximum value for a device, since some drivers try to set MMRBC to the 
highest allowed value and rely on such a function.

Based on patch set by Stephen Hemminger <shemminger@linux-foundation.org>

Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NPeter Oruba <peter.oruba@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Via VT3351 APIC does not play well with MSI and unleashes a flood
of APIC errors when MSI is used to deliver interrupts.  The problem
was recently exposed when the atl1 network device driver, which enables
MSI by default, stimulated APIC errors on an Asus M2V mainboard, which
employs the Via VT3351.
See http://bugzilla.kernel.org/show_bug.cgi?id=8472 for additional
details on this bug.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've been seeing lots of messages like these:

eth0: No interrupt was generated using MSI, switching to INTx mode.  Please
report this failure to the PCI maintainer and include system chipset
information.

On several systems that use the following Severworks HT1000 (also sometimes
labeled as a Broadcom chipset as well) bridge chips.  It doesn't appear MSI
works well (if at all) on these systems.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit c0affe9d doesn't work because
the host controller is being quirked not a PCI bridge.  This patch
reverts the commit, rename quirk_svw_msi() to quirk_disable_all_msi()
and use it instead.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Matias Alejandro Torres <torresmat@gmail.com>
Cc: Greg K-H <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.

The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: NLuugi Marsan <luugi.marsan@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

MSI doesn't work on RS400-200 and RS480 requiring pci=nomsi kernel
boot parameter for ahci to work.  This patch disables MSI on those
chips.

  http://thread.gmane.org/gmane.linux.ide/17820
  http://thread.gmane.org/gmane.linux.ide/17516
  https://bugzilla.novell.com/show_bug.cgi?id=263893Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.

This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.

For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.

In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It was found that the Toshiba laptops with hidden Intel SMBus have SMM
code handling the thermal management which accesses the SMBus. Thus it
is not safe to unhide it and let Linux access it. We have to leave the
SMBus hidden. SMM is a pain, really.

This fixes bugs #6315 and #6395, for good this time.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled.  Currently the code has been
calling disable_msi_mode to try and achieve that.  However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.

Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.

pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit.  A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering.  So the call
in pci_disable_device to disable msi capabilities was redundant.

quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make jmiron_ata quirk update pdev->class after programming the device
and update ahci and pata_jmicron such that they match class code
instead of checking function number manually.  For ahci, it matches
for vendor and class.  For pata_jmicron, it matches vendor, device and
class as IDE class isn't as well defined as AHCI class.

This makes jmicron device matching more conventional and script
friendly.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reimplement jmicron ATA quirk.

* renamed to quirk_jmicron_ata()
* quirk is invoked only for the affected controllers
* programming is stricter.  e.g. conf5 bit24 is cleared if
  unnecessary.
* code factored for readability
* JMB360 and JMB368 are programmed into proper mode

Verified on JMB360, 363 and 368.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NConke Hu <conke.hu@amd.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I don't see any reason why we need pci_msi_quirk, quirk code can just
call pci_no_msi() instead.

Remove the check of pci_msi_quirk in msi_init(). This is safe as all
calls to msi_init() are protected by calls to pci_msi_supported(),
which checks pci_msi_enable, which is disabled by pci_no_msi().

The pci_disable_msi routines didn't check pci_msi_quirk, only
pci_msi_enable, but as far as I can see that was a bug not a feature.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since 2.6.0-test10, all quirk_sis_96x_compatible() had any effect on
was a printk().

This patch therefore removes it.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NMark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Speed up the Intel SMBus PCI quirk by avoiding tests which can only
fail. This also makes the compiled code significantly smaller when
using gcc 3.2/3.4. gcc 4.x appears to optimize the code by itself so
this change doesn't make a difference there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There's an existing quirk for the kernel to use 1k IO space granularity
on the Intel P64H2.  It turns out however that pci_setup_bridge() in
drivers/pci/setup-bus.c reads in the IO base and limit address register
masks it off to the nearest 4k, and writes it back.  This causes the
kernel to be on 1k boundaries and the hardware to be 4k aligned.  The
patch below fixes the problem. 
Signed-off-by: NDan Yeisley <dan.yeisley@unisys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains the following cleanups:
- move all EXPORT_SYMBOL's directly below the code they are exporting
- move all DECLARE_PCI_FIXUP_*'s directly below the functions they
  are calling
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is the driver for the Toshiba TC86C001 GOKU-S PCI IDE controller,
completely reworked from the original brain-damaged Toshiba's 2.4 version.

This single channel UltraDMA/66 controller is very simple in programming,
yet Toshiba managed to plant many interesting bugs in it.  The particularly
nasty "limitation 5" (as they call the errata) caused me to abuse the IDE
core in a possibly most interesting way so far.  However, this is still
better than the #ifdef mess in drivers/ide/ide-io.c that the original
version included (well, it had much more mess)...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAlan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set.  This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.

The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits.  If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.

This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add special handling for the VT82C686.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix VIA quirks that were recently broken by Alan Cox in the upstream
kernel (commit 1597cacb).

My understanding is that pci_find_present() doesn't work yet at the time
the quirks are run.  So I used a two-step quirk as is done for some other
quirks already.  First we detect the VIA south bridges and set the right
low and high device limits, then we are ready to actually run the quirks on
the affected devices.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NNick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Unhide the SMBus on the Asus P4P800-X (and probably some other
models of the family.) This gives access to the memory module SPD
EEPROMs.

Thanks to Winbond for supporting the lm-sensors project with the
donation of this motherboard.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

o MODPOST generates warnings for i386 if kernel is compiled with
  CONFIG_RELOCATABLE=y

WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc_ich6' (at offset 0xc0217d58) and 'quirk_cardbus_legacy'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc' (at offset 0xc0217fd9) and 'pci_match_id'

o Two quirk functions which are non __init, are accessing data which is
  of type __init.
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

The sis96x SMBus PCI device depends on two different quirks to run
in a specific order.  Apart from being fragile, this was found to
actually break on (at least) recent FC4, FC5, and FC6 kernels.  This
patch fixes the quirks so that they work without relying on the
compiler and/or linker to put them in any specific order.

  http://lists.lm-sensors.org/pipermail/lm-sensors/2006-April/015962.html
  https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=189719

I tested this patch.
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Greg K-H <greg@kroah.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

pci_get_slot() may return NULL if nothing was found.  quirk_nvidia_ck804()
does not check the value returned from pci_get_slot(), so it may end up
causing a NULL pointer deref.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is designed to fix:
- Disk eating corruptor on KT7 after resume from RAM
- VIA IRQ handling
- VIA fixups for bus lockups after resume from RAM

The core of this is to add a table of resume fixups run at resume time.
We need to do this for a variety of boards and features, but particularly
we need to do this to get various critical VIA fixups done on resume.

The second part of the problem is to handle VIA IRQ number rules which
are a bit odd and need special handling for PIC interrupts. Various
patches broke various boxes and while this one may not be perfect
(hopefully it is) it ensures the workaround is applied to the right
devices only.

From: Jean Delvare <khali@linux-fr.org>

Now that PCI quirks are replayed on software resume, we can safely
re-enable the Asus SMBus unhiding quirk even when software suspend support
is enabled.

[akpm@osdl.org: fix const warning]
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>