Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.

So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xs4all.nl>.
Reported-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for onboard gpio buzzer. It works using
the gpio-beeper driver. Pinmux entries for GPIO
controlling the buzzer are also added.
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add dra7 iodelay configuration.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

The interrupt for power button is static data that comes from the
datasheet, there is no reason to need to define this value on every
board so seams reasonable put this information into the common tps65217
file.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The interrupt specifiers for USB and AC charger input are static data that
comes from the datasheet, there is no reason to need to define these values
on every board so seem reasonable put this information into the common
tps65217 file.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replace deprecated "vmmc_aux" with the generic "vqmmc" binding for
MMC IO supply.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The GPIO polarity for MMC1 card detect is set to '0' which means
active-high. However the polarity should be active-low. Fix it
here.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The GPIO polarity for MMC1 card detect is set to '0' which means
active-high. However the polarity should be active-low. Fix it
here.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This reverts commits 2c0cba48 ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0f ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use 'clock-frequency' binding for the i2c node that will put the I2C driver
into the standard operating mode. 'speed-mode' was not a valid binding for
the I2C driver, remove it.
Signed-off-by: NAlan Tull <atull@kernel.org>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Add DT alias for the second ethernet present on mainboard rev 1.10.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Drop the LED node from VINing FPGA DT because the LED wiring is
different on each mainboard revision. This wiring is therefore
handled in mainboard DT Overlays.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Remove the EEPROMs attached to the I2C expander ports which
lead to the backplane slots from the main VIN|ING DTS file.
These EEPROMs are bound using separate DTO files, which lets
us handle both two-slot and six-slot configuration of the
backplane.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Enable the QSPI node and add the flash chips.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

The ethernet block clock phandle must point to the clock node which
represents the clock which directly supply the ethernet block. This
is emac_x_clk , not emacx_clk , so fix this.

From: Pavel Machek <pavel@denx.de>
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>

commit 94647a30 ("ARM: dts: omap3-overo: Enable WiFi/BT combo")
while enabling WiFi/BT combo added regulator to trigger the nReset
signal of the Bluetooth module in vqmmc-supply. However BT should be
handled by UART. Moreover "vqmmc" is not a defined binding for
omap_hsmmc. While "vqmmc" in mmc2 hasn't caused any issues so far,
mmc2 will start to mis-behave once omap_hsmmc defines "vqmmc"
binding.

Remove "vqmmc-supply" property in mmc2 here.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add Smart Power System node for PM domains.
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Use a custom S500 enable-method for all CPUs.
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Add "max-frequency" property to MMC dt nodes and set the
maximum frequency to 192MHz for MMC1/MMC2, 64MHz for MMC3
and 192MHz for MMC4. pdata quirks must be utilized to
detect presence of rev 1.1/1.0 of silicon and adjust
maximum frequencies as per restrictions documented in i843.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On DRA75x EVM, MMC2 vdd/ios are connected to a common supply fixed at 1.8V
not 3.3V

Fixes: 6cf02dbb ("ARM: dts: dra7-evm: Add mmc2 node for eMMC support")
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The dt binding documentation of omap-hsmmc recommends using
"vmmc_aux" for IO supply lines. However
commit 0af28cc9 ("ARM: dts: am57xx-beagle-x15: Add support
for rev B1") added it as "vmmc-aux". Now that anyways it
needs to be fixed, use the generic "vqmmc" binding instead of
the deprecated "vmmc_aux".

Fixes: commit 0af28cc9 ("ARM: dts: am57xx-beagle-x15: Add
support for rev B1")
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add vqmmc-supply property to mmc1 dt node and populate
it with ldo1_reg to reflect ldo1_out is connected to mmc1 IO lines.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add vqmmc-supply property to mmc1 dt node and populate
it with ldo1_reg to reflect ldo1_out is connected to mmc1 IO lines.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On dra72/dra71 evms, mmc2 vdd/ios are connected to a common 1.8V supply
not 3.3V. Also the regulator that supplies 1.8V is different on dra71-evm
so move the supply property from common dtsi to evm specific dts files.

Fixes: a4240d3a ("ARM: dts: Add support for dra72-evm rev C (SR2.0)")
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add Device Trees for Actions Semiconductor S500 SoC and LeMaker Guitar SoM
and base board.
Signed-off-by: NAndreas Färber <afaerber@suse.de>

The cm-fx6 module has an on-board AW-NH387 WiFi/BT module which is
based on Marvell's SD8787 chip and is connected to the usdhc1
controller.

Unfortunately, the chip gets unresponsive if the Bluetooth AMP
(Alternate Mac/Phy) function gets probed but the loaded firmware
doesn't support it. For instance, this is the case for the most
recent firmware in linux-firmware (Version 14.66.35.p52).

Thus, just add the required nodes but leave the usdhc1 node disabled
explicitly. Users who disabled the Bluetooth (AMP) support of their
OS can then conveniently enable WiFi (or even plain Bluetooth) support
with a simple device tree overlay/bootloader configuration.
Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The "test" and "conf" nand partitions partly overlap:

Creating 6 MTD partitions on "orion_nand":
0x000000000000-0x000000090000 : "uboot"
0x000000090000-0x0000000d4000 : "env"
0x0000000d4000-0x0000000f8000 : "test"
0x0000000f4000-0x0000004f4000 : "conf"

That is unlikely to be desired, and not matching the partition map used in
u-boot - So adjust the test partition size to fix this.
Signed-off-by: NPeter Korsgaard <peter@korsgaard.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.

But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.

So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The Linksys WRT3200ACM (Rango) is the lates Armada-385 based router in
the Linksys WRT AC Series which got released in October 2016.

Key differences to the earlier Armada-385 based devices in the series is
a bigger flash chip, next generation wireless modules (Marvell 88W8964)
in the mini pcie slots as well as a Marvell SD8887. Finally the CPU is
clocked at 1866 GHz by default.

The file armada-385-linksys-rango.dts is loosly based off of a DTS
authored by Imre Kaloz.

As Rango is part of the armada-385-linksys family of boards use the
armada-385-linksys.dtsi as basis. As for functional differences to Imre
Kaloz dts, the wlan LEDs aren't connected to the expander chip pca9635
but directly to GPIOs. Then mpp47 controls the USB2.0 port and not the
USB3.0 port, so use the correct GPIO mpp44 for it. Finally use
non-removable instead of broken-cd with the sdhci node to avoid polling.

Other changes can be categorized as just cleanup / reorganization due to
using the armada-385-linksys.dtsi.

URL: https://github.com/openwrt/openwrt/blob/0abc3fa5a996daf7dafdc7794ccfe3fa7e955c5a/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-linksys-rango.dtsSigned-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Buttons don't have a reg property; drop pseudo address and fixup names
of individual button nodes. Also drop #address-cells and #size-cells
properties.
Signed-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

A pin group per node is sufficient, further specialization only serves
as documentation which can be a comment just as well. This simplifies
configuring pins for nodes in dependants.

Also use labels which end up right by the node they are intended for.
Signed-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Move the partition layout to individual boards. The Linksys WRT 3200 ACM
(Rango) comes with a 256MiB nand flash chip and different layout.
Signed-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Use IEEE 1541-2002 unit prefixes for sizes.
Signed-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The new ones work so there is little reason to keep the legacy bindings.
Use the rework as the opportunity to drop the legacy node.
Signed-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>