Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 24 7月, 2015 5 次提交
    • C
      tty/serial: at91: add support to FIFOs · b5199d46
      由 Cyrille Pitchen 提交于 
      Depending on the hardware, TX and RX FIFOs may be available. The RX
FIFO can avoid receive overruns, especially when DMA transfers are
not used to read data from the Receive Holding Register. For heavy
system load, The CPU is likely not be able to fetch data fast enough
from the RHR.

In addition, the RX FIFO can supersede the DMA/PDC to control the RTS
line when the Hardware Handshaking mode is enabled. Two thresholds
are to be set for that purpose:
- When the number of data in the RX FIFO crosses and becomes lower
  than or equal to the low threshold, the RTS line is set to low
  level: the remote peer is requested to send data.
- When the number of data in the RX FIFO crosses and becomes greater
  than or equal to the high threshold, the RTS line is set to high
  level: the remote peer should stop sending new data.
- low threshold <= high threshold
Once these two thresholds are set properly, this new feature is
enabled by setting the FIFO RTS Control bit of the FIFO Mode Register.

FIFOs also introduce a new multiple data mode: the USART works either
in multiple data mode or in single data (legacy) mode.

If MODE9 bit is set into the Mode Register or if USMODE is set to
either LIN_MASTER, LIN_SLAVE or LON_MODE, FIFOs operate in single
data mode. Otherwise, they operate in multiple data mode.

In this new multiple data mode, accesses to the Receive Holding
Register or Transmit Holding Register slightly change.

Since this driver implements neither the 9bit data feature (MODE9 bit
set into the Mode Register) nor LIN modes, the USART works in
multiple data mode whenever FIFOs are available and enabled. We also
assume that data are 8bit wide.

In single data mode, 32bit access CAN be used to read a single data
from RHR or write a single data into THR.
However in multiple data mode, a 32bit access to RHR now allows us to
read four consecutive data from RX FIFO. Also a 32bit access to THR
now allows to write four consecutive data into TX FIFO. So we MUST
use 8bit access whenever only one data have to be read/written at a
time.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b5199d46
    • C
      tty/serial: at91: fix some macro definitions to fit coding style · 3fad3860
      由 Cyrille Pitchen 提交于 
      This patch updates macro definitions in atmel_serial.h to fit the
80 column rule.

Please note that some deprecated comments such as "[AT91SAM9261 only]"
are removed as the corresponding bits also exist in some later chips.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      3fad3860
    • J
      tty: linux/gsmmux.h needs linux/types.h · 45c6df44
      由 Jiri Slaby 提交于 
      We use __u8 in linux/gsmmux.h, so include linux/types.h to have that
defined.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      45c6df44
    • V
      tty/early: make serial8250_early_{in,out} static again · f3fb7ef3
      由 Vineet Gupta 提交于 
      Commit ed71871b ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override

However recent updates to core, specifically ebc5e200 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3f
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.

Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: NNoam Camus <noamc@ezchip.com>
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      f3fb7ef3
    • P
      serial: 8250: Split base port operations from universal driver · b6830f6d
      由 Peter Hurley 提交于 
      Refactor base port operations into new file; 8250_port.c.

Legacy irq handling, RSA port support, port storage for universal
driver, driver definition, module parameters and linkage remain in
8250_core.c

The source file split and resulting modules is diagrammed below:

  8250_core.c ====>   8250_core.c __
              \                     \
               \                     +-- 8250.ko (alias 8250_core)
                \     8250_pnp.c  __/     (universal driver)
                 \
                  =>  8250_port.c __
                                    \
                                     +-- 8250_base.ko
                      8250_dma.c  __/     (port operations)
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b6830f6d
  3. 18 7月, 2015 7 次提交
  5. 16 7月, 2015 1 次提交
  7. 15 7月, 2015 2 次提交
  9. 13 7月, 2015 3 次提交
  11. 10 7月, 2015 5 次提交
    • P
      KVM: count number of assigned devices · 5544eb9b
      由 Paolo Bonzini 提交于 
      If there are no assigned devices, the guest PAT are not providing
any useful information and can be overridden to writeback; VMX
always does this because it has the "IPAT" bit in its extended
page table entries, but SVM does not have anything similar.
Hook into VFIO and legacy device assignment so that they
provide this information to KVM.
Reviewed-by: NAlex Williamson <alex.williamson@redhat.com>
Tested-by: NJoerg Roedel <jroedel@suse.de>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      5544eb9b
    • E
      cdc_ncm: Add support for moving NDP to end of NCM frame · 4a0e3e98
      由 Enrico Mioso 提交于 
      NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.

This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).

V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4a0e3e98
    • T
      blkcg: fix blkcg_policy_data allocation bug · 06b285bd
      由 Tejun Heo 提交于 
      e48453c3 ("block, cgroup: implement policy-specific per-blkcg
data") updated per-blkcg policy data to be dynamically allocated.
When a policy is registered, its policy data aren't created.  Instead,
when the policy is activated on a queue, the policy data are allocated
if there are blkg's (blkcg_gq's) which are attached to a given blkcg.
This is buggy.  Consider the following scenario.

1. A blkcg is created.  No blkg's attached yet.

2. The policy is registered.  No policy data is allocated.

3. The policy is activated on a queue.  As the above blkcg doesn't
   have any blkg's, it won't allocate the matching blkcg_policy_data.

4. An IO is issued from the blkcg and blkg is created and the blkcg
   still doesn't have the matching policy data allocated.

With cfq-iosched, this leads to an oops.

It also doesn't free policy data on policy unregistration assuming
that freeing of all policy data on blkcg destruction should take care
of it; however, this also is incorrect.

1. A blkcg has policy data.

2. The policy gets unregistered but the policy data remains.

3. Another policy gets registered on the same slot.

4. Later, the new policy tries to allocate policy data on the previous
   blkcg but the slot is already occupied and gets skipped.  The
   policy ends up operating on the policy data of the previous policy.

There's no reason to manage blkcg_policy_data lazily.  The reason we
do lazy allocation of blkg's is that the number of all possible blkg's
is the product of cgroups and block devices which can reach a
surprising level.  blkcg_policy_data is contrained by the number of
cgroups and shouldn't be a problem.

This patch makes blkcg_policy_data to be allocated for all existing
blkcg's on policy registration and freed on unregistration and removes
blkcg_policy_data handling from policy [de]activation paths.  This
makes that blkcg_policy_data are created and removed with the policy
they belong to and fixes the above described problems.
Signed-off-by: NTejun Heo <tj@kernel.org>
Fixes: e48453c3 ("block, cgroup: implement policy-specific per-blkcg data")
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
      06b285bd
    • T
      blkcg: implement all_blkcgs list · 7876f930
      由 Tejun Heo 提交于 
      Add all_blkcgs list goes through blkcg->all_blkcgs_node and is
protected by blkcg_pol_mutex.  This will be used to fix
blkcg_policy_data allocation bug.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
      7876f930
    • I
      libceph: enable ceph in a non-default network namespace · 757856d2
      由 Ilya Dryomov 提交于 
      Grab a reference on a network namespace of the 'rbd map' (in case of
rbd) or 'mount' (in case of ceph) process and use that to open sockets
instead of always using init_net and bailing if network namespace is
anything but init_net.  Be careful to not share struct ceph_client
instances between different namespaces and don't add any code in the
!CONFIG_NET_NS case.

This is based on a patch from Hong Zhiguo <zhiguohong@tencent.com>.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>
      757856d2
  13. 09 7月, 2015 2 次提交
  15. 08 7月, 2015 3 次提交
    • T
      hotplug: Prevent alloc/free of irq descriptors during cpu up/down · a8994181
      由 Thomas Gleixner 提交于 
      When a cpu goes up some architectures (e.g. x86) have to walk the irq
space to set up the vector space for the cpu. While this needs extra
protection at the architecture level we can avoid a few race
conditions by preventing the concurrent allocation/free of irq
descriptors and the associated data.

When a cpu goes down it moves the interrupts which are targeted to
this cpu away by reassigning the affinities. While this happens
interrupts can be allocated and freed, which opens a can of race
conditions in the code which reassignes the affinities because
interrupt descriptors might be freed underneath.

Example:

CPU1				CPU2
cpu_up/down
 irq_desc = irq_to_desc(irq);
				remove_from_radix_tree(desc);
 raw_spin_lock(&desc->lock);
				free(desc);

We could protect the irq descriptors with RCU, but that would require
a full tree change of all accesses to interrupt descriptors. But
fortunately these kind of race conditions are rather limited to a few
things like cpu hotplug. The normal setup/teardown is very well
serialized. So the simpler and obvious solution is:

Prevent allocation and freeing of interrupt descriptors accross cpu
hotplug.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: xiao jin <jin.xiao@intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Link: http://lkml.kernel.org/r/20150705171102.063519515@linutronix.de
      a8994181
    • T
      tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build · 37b64a42
      由 Thomas Gleixner 提交于 
      Making tick_broadcast_oneshot_control() independent from
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST broke the build for
CONFIG_GENERIC_CLOCKEVENTS=n because the function is not defined
there.

Provide a proper stub inline.

Fixes: f32dd117 'tick/broadcast: Make idle check independent from mode and config'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
      37b64a42
    • T
      tick/broadcast: Make idle check independent from mode and config · f32dd117
      由 Thomas Gleixner 提交于 
      Currently the broadcast busy check, which prevents the idle code from
going into deep idle, works only in one shot mode.

If NOHZ and HIGHRES are off (config or command line) there is no
sanity check at all, so under certain conditions cpus are allowed to
go into deep idle, where the local timer stops, and are not woken up
again because there is no broadcast timer installed or a hrtimer based
broadcast device is not evaluated.

Move tick_broadcast_oneshot_control() into the common code and provide
proper subfunctions for the various config combinations.

The common check in tick_broadcast_oneshot_control() is for the C3STOP
misfeature flag of the local clock event device. If its not set, idle
can proceed. If set, further checks are necessary.

Provide checks for the trivial cases:

 - If broadcast is disabled in the config, then return busy

 - If oneshot mode (NOHZ/HIGHES) is disabled in the config, return
   busy if the broadcast device is hrtimer based.

 - If oneshot mode is enabled in the config call the original
   tick_broadcast_oneshot_control() function. That function needs
   extra checks which will be implemented in seperate patches.

[ Split out from a larger combo patch ]
Reported-and-tested-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Suzuki Poulose <Suzuki.Poulose@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Catalin Marinas <Catalin.Marinas@arm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1507070929360.3916@nanos
      f32dd117
  17. 07 7月, 2015 2 次提交
    • S
      ACPI / scan: Add support for ACPI _CLS device matching · 26095a01
      由 Suthikulpanit, Suravee 提交于 
      Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.

To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.

    acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
    # cat /sys/devices/platform/AMDI0600:00/modalias
    acpi:AMDI0600:010601:

where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code

Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.

    static const struct acpi_device_id ahci_acpi_match[] = {
        { ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
        {},
    };

In this case, the corresponded entry in modules.alias file would be:

    alias acpi*:010601:* ahci_platform
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      26095a01
    • R
      ACPI / PNP: Reserve ACPI resources at the fs_initcall_sync stage · 0294112e
      由 Rafael J. Wysocki 提交于 
      This effectively reverts the following three commits:

 7bc10388 ACPI / resources: free memory on error in add_region_before()
 0f1b414d ACPI / PNP: Avoid conflicting resource reservations
 b9a5e5e1 ACPI / init: Fix the ordering of acpi_reserve_resources()

(commit b9a5e5e1 introduced regressions some of which, but not
all, were addressed by commit 0f1b414d and commit 7bc10388
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.

The story is as follows.  First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes.  Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.

The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e1).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d.

That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook.  That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d wouldn't be
necessary any more.

For this reason, the changes made by commit 0f1b414d are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e1 that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: NRoland Dreier <roland@purestorage.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      0294112e
  19. 06 7月, 2015 1 次提交
    • P
      module: relocate module_init from init.h to module.h · 0fd972a7
      由 Paul Gortmaker 提交于 
      Modular users will always be users of init functionality, but
users of init functionality are not necessarily always modules.

Hence any functionality like module_init and module_exit would
be more at home in the module.h file.  And module.h should
explicitly include init.h to make the dependency clear.

We've already done all the legwork needed to ensure that this
move does not cause any build regressions due to implicit
header file include assumptions about where module_init lives.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
      0fd972a7
  21. 05 7月, 2015 2 次提交
  23. 04 7月, 2015 3 次提交
  25. 03 7月, 2015 1 次提交
    • J
      irqchip: Move IRQCHIP_DECLARE macro to include/linux/irqchip.h · 91e20b50
      由 Joel Porquet 提交于 
      At the moment the IRQCHIP_DECLARE macro is only declared locally in
drivers/irqchip/irqchip.h. It prevents from using it directly in arch/*
directories whenever irqchip drivers only exist there, which happens in a few
cases (e.g. arc, arm, microblaze and mips).

This patch makes the macro to be globally defined, i.e. in
include/linux/irqchip.h, and thus usable for arch-specific declarations of
irqchip drivers. In this way, it is very similar to what clocksource does (ie
CLOCKSOURCE_OF_DECLARE is defined in include/linux/clocksource.h).

For now, this patch only moves the declaration of the macro
IRQCHIP_DECLARE to the global header 'include/linux/irqchip.h' and make
'drivers/irqchip/irqchip.h' include 'include/linux/irqchip.h'. Later, other
patches will get rid of 'drivers/irqchip/irqchip.h' and modify all the impacted
irqchip drivers.
Signed-off-by: NJoel Porquet <joel@porquet.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1435865565-14114-1-git-send-email-joel@porquet.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      91e20b50
  27. 02 7月, 2015 3 次提交
    • T
      writeback: don't embed root bdi_writeback_congested in bdi_writeback · a13f35e8
      由 Tejun Heo 提交于 
      52ebea74 ("writeback: make backing_dev_info host cgroup-specific
bdi_writebacks") made bdi (backing_dev_info) host per-cgroup wb's
(bdi_writeback's).  As the congested state needs to be per-wb and
referenced from blkcg side and multiple wbs, the patch made all
non-root cong's (bdi_writeback_congested's) reference counted and
indexed on bdi.

When a bdi is destroyed, cgwb_bdi_destroy() tries to drain all
non-root cong's; however, this can hang indefinitely because wb's can
also be referenced from blkcg_gq's which are destroyed after bdi
destruction is complete.

To fix the bug, bdi destruction will be updated to not wait for cong's
to drain, which naturally means that cong's may outlive the associated
bdi.  This is fine for non-root cong's but is problematic for the root
cong's which are embedded in their bdi's as they may end up getting
dereferenced after the containing bdi's are freed.

This patch makes root cong's behave the same as non-root cong's.  They
are no longer embedded in their bdi's but allocated separately during
bdi initialization, indexed and reference counted the same way.

* As cong handling is the same for all wb's, wb->congested
  initialization is moved into wb_init().

* When !CONFIG_CGROUP_WRITEBACK, there was no indexing or refcnting.
  bdi->wb_congested is now a pointer pointing to the root cong
  allocated during bdi init and minimal refcnting operations are
  implemented.

* The above makes root wb init paths diverge depending on
  CONFIG_CGROUP_WRITEBACK.  root wb init is moved to cgwb_bdi_init().

This patch in itself shouldn't cause any consequential behavior
differences but prepares for the actual fix.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NJon Christopherson <jon@jons.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100681Tested-by: NJon Christopherson <jon@jons.org>

Added <linux/slab.h> include to backing-dev.h for kfree() definition.
Signed-off-by: NJens Axboe <axboe@fb.com>
      a13f35e8
    • A
      NTB: Move files in preparation for NTB abstraction · ec110bc7
      由 Allen Hubbe 提交于 
      This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer.  Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>
      ec110bc7
    • N
      bufferhead: Add _gfp version for sb_getblk() · bd7ade3c
      由 Nikolay Borisov 提交于 
      sb_getblk() is used during ext4 (and possibly other FSes) writeback
paths. Sometimes such path require allocating memory and guaranteeing
that such allocation won't block. Currently, however, there is no way
to provide user flags for sb_getblk which could lead to deadlocks.

This patch implements a sb_getblk_gfp with the only difference it can
accept user-provided GFP flags.
Signed-off-by: NNikolay Borisov <kernel@kyup.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
      bd7ade3c