In order to make sure API users don't try to use SGIDs which don't
conform to the routing table, validate the route before searching
the RoCE GID table.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In order to support multiple GID types, we need to store the gid_type
with each GID. This is also aligned with the RoCE v2 annex "RoCEv2 PORT
GID table entries shall have a "GID type" attribute that denotes the L3
Address type". The currently supported GID is IB_GID_TYPE_IB which is
also RoCE v1 GID type.

This implies that gid_type should be added to roce_gid_table meta-data.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

It was found by Saurabh Sengar that the netlink code tried to allocate
memory with GFP_KERNEL while holding a spinlock. While it is possible
to fix the issue by replacing GFP_KERNEL with GFP_ATOMIC, it is better
to get rid of the spinlock while sending the packet. However, in order
to protect against a race condition that a quick response may be received
before the request is put on the request list, we need to put the request
on the list first.
Signed-off-by: NKaike Wan <kaike.wan@intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reported-by: NSaurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

mm, page_alloc: distinguish between being unable to sleep, unwilling to sleep and avoiding waking kswapd

__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts.  They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve".  __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".

Over time, callers had a requirement to not block when fallback options
were available.  Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.

This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative.  High priority users continue to use
__GFP_HIGH.  __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim.  __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim.  __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.

This patch then converts a number of sites

o __GFP_ATOMIC is used by callers that are high priority and have memory
  pools for those requests. GFP_ATOMIC uses this flag.

o Callers that have a limited mempool to guarantee forward progress clear
  __GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
  into this category where kswapd will still be woken but atomic reserves
  are not used as there is a one-entry mempool to guarantee progress.

o Callers that are checking if they are non-blocking should use the
  helper gfpflags_allow_blocking() where possible. This is because
  checking for __GFP_WAIT as was done historically now can trigger false
  positives. Some exceptions like dm-crypt.c exist where the code intent
  is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
  flag manipulations.

o Callers that built their own GFP flags instead of starting with GFP_KERNEL
  and friends now also need to specify __GFP_KSWAPD_RECLAIM.

The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.

The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL.  They may
now wish to specify __GFP_KSWAPD_RECLAIM.  It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: NMel Gorman <mgorman@techsingularity.net>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Acked-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The GID cache accompanies every GID with attributes.
The GID attributes link the GID with its netdevice, which could be
resolved to smac and vlan id easily. Since we've added the netdevice
(ifindex and net) to the path record, storing the L2 attributes is
duplicated data and hence these attributes are removed.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-By: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Smac and vlan id could be resolved from the GID attribute, and thus
these attributes aren't needed anymore. Removing them.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-By: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In order to find the sgid_index, one could just query the IB cache
with the correct GID and netdevice. Therefore, instead of storing
the L2 attributes directly in the path, we only store the
ifindex and net and use them later to get the sgid_index.
The vlan_id and smac L2 attributes are removed in a later patch.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-By: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Adding an ability to query the IB cache by a netdev and get the
attributes of a GID. These parameters are necessary in order to
successfully resolve the required GID (when the netdevice is known)
and get the Ethernet L2 attributes from a GID.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-By: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The flags to ibnl_put_msg should be NLM_F_REQUEST instead of GFP_KERNEL.
Signed-off-by: NKaike Wan <kaike.wan@intel.com>
Signed-off-by: NJohn Fleck <john.fleck@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch routes a SA pathrecord query to netlink first and processes the
response appropriately. If a failure is returned, the request will be sent
through IB. The decision whether to route the request to netlink first is
determined by the presence of a listener for the local service netlink
multicast group. If the user-space local service netlink multicast group
listener is not present, the request will be sent through IB, just like
what is currently being done.
Signed-off-by: NKaike Wan <kaike.wan@intel.com>
Signed-off-by: NJohn Fleck <john.fleck@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Replace kmalloc with kzalloc so that all uninitialized fields in SA query
will be zero-ed out to avoid unintentional consequence. This prepares the
SA query structure to accept new fields in the future.
Signed-off-by: NKaike Wan <kaike.wan@intel.com>
Signed-off-by: NJohn Fleck <john.fleck@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

An ib_client callback that is called with the lists_rwsem locked only for
read is protected from changes to the IB client lists, but not from
ib_unregister_device() freeing its client data. This is because
ib_unregister_device() will remove the device from the device list with
lists_rwsem locked for write, but perform the rest of the cleanup,
including the call to remove() without that lock.

Mark client data that is undergoing de-registration with a new going_down
flag in the client data context. Lock the client data list with lists_rwsem
for write in addition to using the spinlock, so that functions calling the
callback would be able to lock only lists_rwsem for read and let callbacks
sleep.

Since ib_unregister_client() now marks the client data context, no need for
remove() to search the context again, so pass the client data directly to
remove() callbacks.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Persuant to Liran's comments on node_type on linux-rdma
mailing list:

In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".

In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).

The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-By: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Tested-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NHal Rosenstock <hal@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In preparation to support the new OPA MAD Base version, add a base version
parameter to ib_create_send_mad and set it to IB_MGMT_BASE_VERSION for current
users.

Definition of the new base version and it's processing will occur in later
patches.
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Registering an event handler is done for a device. This device may have
one RoCE port (no SA cap) and one InfiniBand port (has SA cap).
Therefore, warning from the event handler about a specific port that
doesn't have SA cap is correct but pollutes the kernel log without a
need.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Introduce helper rdma_cap_eth_ah() to help us check if the port of an
IB device support Ethernet Address Handler.
Signed-off-by: NMichael Wang <yun.wang@profitbricks.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Tested-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: NDoug Ledford <dledford@redhat.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Introduce helper rdma_cap_ib_sa() to help us check if the port of an
IB device support Infiniband Subnet Administration.
Signed-off-by: NMichael Wang <yun.wang@profitbricks.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Tested-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: NDoug Ledford <dledford@redhat.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use raw management helpers to reform IB-core sa_query.
Signed-off-by: NMichael Wang <yun.wang@profitbricks.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Tested-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: NDoug Ledford <dledford@redhat.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Registrations options are specified through flags.  Definitions of flags will
be in subsequent patches.
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Properly convert gfp_t & result to bool to fix:

    drivers/infiniband/core/sa_query.c:621:33: warning: incorrect type in initializer (different base types)
    drivers/infiniband/core/sa_query.c:621:33:    expected bool [unsigned] [usertype] preload
    drivers/infiniband/core/sa_query.c:621:33:    got restricted gfp_t
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.

When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.

Thus, those attributes were added to the following structures:

* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id

For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.

On the active side, the CM fills. its internal structures from the
path provided by the ULP.  We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).

On the passive side, the CM fills its internal structures from the WC
associated with the REQ message.  We add there taking the ETH L2
attributes from the WC.

When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.

ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB.  Vendor drivers are modified to support the new
function signature.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Allow converting from struct ib_sa_path_rec to the IB defined SA path
record wire format.  This will be used to report path data from the
rdma cm into user space.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Convert to the much saner new idr interface.

v2: Mike triggered WARN_ON() in idr_preload() because send_mad(),
    which may be used from non-process context, was calling
    idr_preload() unconditionally.  Preload iff @gfp_mask has
    __GFP_WAIT.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Reported-by: N"Marciniszyn, Mike" <mike.marciniszyn@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This query is needed for SRIOV alias GUID support.

The query is implemented per the IB Spec definition
in section 15.2.5.18 (GuidInfoRecord).
Signed-off-by: NErez Shitrit <erezsh@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Commit f0626710 ("RDMA: Update workqueue usage") introduced ib_wq
and removed the use of flush_scheduled_work(); however, during the merge
process one chunk was lost in ib_sa_remove_one().  Fix it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

* ib_wq is added, which is used as the common workqueue for infiniband
  instead of the system workqueue.  All system workqueue usages
  including flush_scheduled_work() callers are converted to use and
  flush ib_wq.

* cancel_delayed_work() + flush_scheduled_work() converted to
  cancel_delayed_work_sync().

* qib_wq is removed and ib_wq is used instead.

This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for IBoE device binding and IP --> GID resolution.  Path
resolving and multicast joining are implemented within cma.c by
filling in the responses and running callbacks in the CMA work queue.

IP --> GID resolution always yields IPv6 link local addresses; remote
GIDs are derived from the destination MAC address of the remote port.
Multicast GIDs are always mapped to multicast MACs as is done in IPv6.
(IPv4 multicast is enabled by translating IPv4 multicast addresses to
IPv6 multicast as described in
<http://www.mail-archive.com/ipng@sunroof.eng.sun.com/msg02134.html>.)

Some helper functions are added to ib_addr.h.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Since IBoE is using Ethernet as its link layer, there is no central
management entity so there is need for QP0.  QP1 is still needed since
it handles communications between CM agents.  This patch will skip QP0
and create only QP1 for IBoE ports.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Export rdma_set_ib_paths to user space to allow applications to
manually set the IB path used for connections.  This allows
alternative ways for a user space application or library to obtain
path record information, including retrieving path information
from cached data, avoiding direct interaction with the IB SA.
The IB SA is a single, centralized entity that can limit scaling
on large clusters running MPI applications.

Future changes to the rdma cm can expand on this framework to
support the full range of features allowed by the IB CM, such as
separate forward and reverse paths and APM.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-By: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Rather than just defining static spinlock_t variables and then
initializing them later in init functions, simply define them with
DEFINE_SPINLOCK() and remove the calls to spin_lock_init().  This cleans
up the source a tad and also shrinks the compiled code; eg on x86-64:

add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-40 (-40)
function                                     old     new   delta
ib_uverbs_init                               336     326     -10
ib_mad_init_module                           147     137     -10
ib_sa_init                                   123     103     -20
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Our testing uncovered a race condition in ib_sa_event():

	spin_lock_irqsave(&port->ah_lock, flags);
	if (port->sm_ah)
		kref_put(&port->sm_ah->ref, free_sm_ah);
	port->sm_ah = NULL;
	spin_unlock_irqrestore(&port->ah_lock, flags);

	schedule_work(&sa_dev->port[event->element.port_num -
				    sa_dev->start_port].update_task);

If two events occur back-to-back (e.g., client-reregister and LID
change), both may pass the spinlock-protected code above before the
scheduled work updates the port->sm_ah handle.  Then if the scheduled
work ends up running twice, the second operation will then find a
non-NULL port->sm_ah, and will simply overwrite it in update_sm_ah --
resulting in an AH leak.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If update_sm_ah() fails, it leaves the port's sm_ah as NULL.  Then if
the device or module is removed, ib_sa_remove_one() will dereference a
NULL pointer when it calls kref_put().  Fix this by testing if sm_ah
is NULL before dropping the reference.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

They don't get updated by git and so they're worse than useless.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch solves a race that occurs after an event occurs that causes
the SA query module to flush its SM address handle (AH).  When SM AH
becomes invalid and needs an update it is handled by the global
workqueue.  On the other hand this event is also handled in the IPoIB
driver by queuing work in the ipoib_workqueue that does multicast
joins.  Although queuing is in the right order, it is done to 2
different workqueues and so there is no guarantee that the first to be
queued is the first to be executed.

This causes a problem because IPoIB may end up sending an request to
the old SM, which will take a long time to time out (since the old SM
is gone); this leads to a much longer than necessary interruption in
multicast traffer.

The patch sets the SA query module's SM AH to NULL when the event
occurs, and until update_sm_ah() is done, any request that needs sm_ah
fails with -EAGAIN return status.

For consumers, the patch doesn't make things worse.  Before the patch,
MADs are sent to the wrong SM so the request gets lost.  Consumers can
be improved if they examine the return code and respond to EAGAIN
properly but even without an improvement the situation is not getting
worse.
Signed-off-by: NMoni Levy <monil@voltaire.com>
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The QoS annex defines new fields for path records.  Add them to the
ib_sa for consumers that want to use them.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ib_create_send_mad() returns an error code pointer on error, not NULL.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Now that ib_find_pkey() ignores the membership bit of P_Keys, there's no
need for ib_sa to look for both 0x7fff and 0xffff in a port's P_Key table.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

MADs sent to the SA should use the the default P_Key (0x7fff/0xffff).
There's no requirement that the default P_Key is stored at index 0 in
the local P_Key table, so add code to the sa_query module to look up
the index of the default P_Key when creating an address handle for the
SA (which is done any time the P_Key table might change), and use this
index for all SA queries.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A few files had 0xa0 characters in comments.  Remove them so that the 
files are clean ASCII text.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.

In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.

My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:

arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c

I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.

Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
  [PATCH] scatterlist.h needs types.h
  http://lkml.org/lkml/2007/3/01/141Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>