There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This basically reverts commit b207cdb0.

Now is possible to use drv_{add,remove}_interface() and vif->debugfs_dir
to create/remove per interface debugfs files. Remove redundant
callbacks.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There is need create driver own per interface debugfs files. This is
currently done by drv_{add,remove}_interface_debugfs() callbacks. But it
is possible that after we remove interface from the driver (i.e.
on suspend) we call drv_remove_interface_debugfs() function. Fixing this
problem will require to add call drv_{add,remove}_interface_debugfs()
anytime we create and remove interface in mac80211. So it's better to
add debugfs dir dentry to vif structure to allow to create/remove
custom debugfs driver files on drv_{add,remove}_interface().
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some devices have multicast filter capability for each individual
virtual interface rather than just a global one. Add an interface
specific driver callback allowing such drivers to configure this.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The irqsafe version ieee80211_sta_eosp_irqsafe() exists, but
drivers must not mix calls to any irqsafe/non-irqsafe function.
Both ath9k and iwlwifi, the likely first users of this interface,
use non-irqsafe RX/TX/TX status so must also use a non-irqsafe
version of this function. Since no driver uses the _irqsafe()
version, remove that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement restricting peer VHT capabilities to the device's own
capabilities. This is useful when a single driver supports more
than one device and the devices have different capabilities
(often they will differ in the number of spatial streams), but
in particular is also necessary for VHT capability overrides to
work correctly -- otherwise it'd be possible to e.g. advertise,
due to overrides, that TX-STBC is not supported, but then still
use it to TX to the AP because it supports RX-STBC.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no driver using this flag, so it seems
that all drivers support HW crypto with WMM or
don't support it at all. Remove the flag and
code setting it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For HT and VHT the current bandwidth can change,
add the function ieee80211_vif_change_bandwidth()
to take care of this. It returns a failure if the
new bandwidth isn't compatible with the existing
channel context, the caller has to handle that.
When it happens, also inform the driver that the
bandwidth changed for this virtual interface (no
drivers would actually care today though.)

Changing to/from HT/VHT isn't allowed though.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Handle the operating mode notification action frame.
When the supported streams or the bandwidth change
let the driver and rate control algorithm know.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With VHT, a station can change the number of spatial
streams it can receive on the fly, not unlike spatial
multiplexing in HT. Prepare for that by tracking the
maximum number of spatial streams it can receive when
the connection is established.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.

To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.

If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.

Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.

While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.

Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.

Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Scans currently work by stopping the netdev tx queues but leaving the
mac80211 queues active. This stops the flow of incoming packets while
still allowing mac80211 to transmit nullfunc and probe request frames to
facilitate scanning. However, the driver may try to wake the mac80211
queues while in this state, which will also wake the netdev queues.

To prevent this, add a new queue stop reason,
IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx
queues for off-channel operation. This prevents the netdev queues from
waking when a driver wakes the mac80211 queues.

This also stops all frames from being transmitted, even those meant to
be sent off-channel. Add a new tx control flag,
IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted
when the queues are stopped only for the off-channel stop reason. Update
all locations transmitting off-channel frames to use this flag.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.

The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The functions were added for some sort of Bluetooth
coexistence, but aren't used, so remove them again.
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to be able to predict the next DTIM TBTT
in the driver, add the ability to use timing data
from beacons only with the new hardware flag
IEEE80211_HW_TIMING_BEACON_ONLY and the BSS info
value sync_dtim_count which is only valid if the
timing data came from a beacon. The data can only
come from a beacon, and if no beacon was received
before association it is updated later together
with the DTIM count notification.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add debugfs driver callbacks so drivers can add
debugfs entries for interfaces. Note that they
_must_ remove the entries again as add/remove in
the driver doesn't correspond to add/remove in
debugfs; the former is up/down while the latter
is netdev create/destroy.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With multi-channel, there's a corner case where a driver
doesn't receive a beacon soon enough to be able to sync
its timers with the AP. In this case, the only recovery
(after trying again) is to disconnect from the AP. Allow
calling ieee80211_connection_loss() for such cases. To
make that possible, modify the work function to not rely
on the IEEE80211_HW_CONNECTION_MONITOR flag but use new
state kept in the interface instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.

For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.

To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.

Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is basically a revert of:

commit 5b632fe8
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Mon Dec 3 12:56:33 2012 +0100

    mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL

We do not need this flag any longer, rt2x00 BAR/BA problem was fixed
correctly by wireless-testing commit:

commit 84e9e8eb
Author: Helmut Schaa <helmut.schaa@googlemail.com>
Date:   Thu Jan 17 17:34:32 2013 +0100

    rt2x00: Improve TX status handling for BlockAckReq frames
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.

Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.

When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.

In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When building the 80211 DocBook, scripts/kernel-doc reports
the following type of warnings:

Warning(include/net/cfg80211.h:334): No description found for return value of 'cfg80211_get_chandef_type'

These warnings are only reported when scripts/kernel-doc
runs in verbose mode.

To fix these use "Return:" to describe function return values.
Signed-off-by: NYacine Belkadi <yacine.belkadi.1@gmail.com>
[adjust for freq_reg_info() change]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use __aligned(...) instead of __attribute__((aligned(...)))
in mac80211 and cfg80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When TX aggregation is stopped, there are a few
different cases:
 - connection with the peer was dropped
 - session stop was requested locally
 - session stop was requested by the peer
 - connection was dropped while a session is stopping

The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.

Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.

In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During suspend/resume channel contexts might be
iterated even if they haven't been re-added to
the driver, keep track of this and skip them in
iteration. Also use the new status for sanity
checks.

Also clarify the fact that during HW restart all
contexts are iterated over (thanks Eliad.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit f0425bed "mac80211: retry sending
failed BAR frames later instead of tearing down aggr" caused regression
on rt2x00 hardware (connection hangs). This regression was fixed by
commit be03d4a4 "rt2x00: Don't let
mac80211 send a BAR when an AMPDU subframe fails". But the latter
commit caused yet another problem reported in
https://bugzilla.kernel.org/show_bug.cgi?id=42828#c22

After long discussion in this thread:
http://mid.gmane.org/20121018075615.GA18212@redhat.com
and testing various alternative solutions, which failed on one or other
setup, we have no other good fix for the issues like just revert both
mentioned earlier commits.

To do not affect other hardware which benefit from commit
f0425bed, instead of reverting it,
introduce flag that when used will restore mac80211 behaviour before
the commit.

Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
[replaced link with mid.gmane.org that has message-id]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of allocating a temporary buffer to build IEs
build them right into the SKB.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support to mac80211 for having drivers report
received VHT MCS information.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>