These ended up causing too many problems on older parts,
revert for now..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This enables the SM501 drivers for the R2D board. Additional
work needs to be done to migrate off of the VoyagerGX cchip
code to make use of the rest of the mfd infrastructure.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously this was using a hardcoded 32, use L1_CACHE_BYTES for
cacheline alignment instead.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When I run a preemptive kernel-2.6.20 for SH7780, a created
kthread(pdflush) can not exit by do_exit() in kernel_thread_helper. I
think that the created kthread should have a room for 'struct pt_regs'
space on the stack top, because __switch_to() will refer to the space as
follows using 'regs = task_pt_regs(prev)' and next condition may be true.
Signed-off-by: NHideo Saito <saito@densan.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There was a missing return in do_signal() that caused the saved
sigmask to be written back after having successfully delivered
the signal.
Signed-off-by: NRyusuke Sakato <sakato@hsdv.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This takes care of tearing down the UBC so it's not inadvertently
left configured at the next context switch time. Failure to do
this results in spurious SIGTRAPs in certain debug sequences.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch clears PCI errors after showing more debug informations.
Signed-off-by: NFlorian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds cardbus ressources for MTX1 boards which have a PCMCIA controller.
Signed-off-by: NFlorian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch removes unnecessary settings at setup time.
Signed-off-by: NFlorian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch has removed unused timer resource.
Moreover, the name of reserved resources ware changed.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

early_printk is a so much saner thing.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If R4k counter was used for hpt_timer and interrupt source,
c0_hpt_timer_init() initializes the c0_compare register.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick).  This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This was causing oprofile to fail on R10000, R12000, R14000.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Work around EBSA110 build errors by selecting NO_IOPORT.  EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

No need to stop tc35815 before resetting the board.  This fixes the
build of tc35815 as a module.  This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just leave them as zero if we couldn't calculate it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We mistakedly modify 'bus' in the innermost loop.  What
should happen is that at each register index iteration,
we start with the same 'bus'.

So preserve it's value at the top level, and use a loop
local variable 'dbus' for iteration.

This bug causes registers other than the first to be
decoded improperly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update help text with location of documentation
and duplicate the note on the speed of CRC
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Always allow backtrace when using oprofile on ARM, even if a PMU
isn't present.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use linux/delay.h not asm/delay.h
Signed-off-by: NTony Lindgren <tony@atomide.com>

Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing includes to board-nokia770 to make it
compile again.

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Workqueue changes for board-h4.c

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When I went to use dmtimer7 it did not seem to work.  I noticed that
the base addresses for dmtimers 7 and 8 were set wrong.  A simple patch
to correct a small error.  Confirmed to fix the problem on an OSK.
Signed-off-by: NMatthew Percival <matthew@capgo.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.

This one-liner fixe the trouble.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Teach OMAP2 gp timer that HZ isn't always 100.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix warning

arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix broken CONFIG_DEBUG_LL. In case of low level debugging
reconfigure some clocks early.

See

http://source.mvista.com/git/gitweb.cgi?p=linux-omap-2.6.git;a=commitdiff;h=3bfb289ccc6c4624fd5ff0381546935e105f4093

too.

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix warning

arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>