We don't really have a max tx packet size limit, so allow configuring
the device with up to 64k tx MTU.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Join the move away from the obsolete info() macro, opencoding the
remaining uses. While we're at it, also get rid of the warn() macro
by promoting the three remaining uses to err().
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The N_GIGASET_M101 line discipline implemented by the ser_gigaset
driver does not transfer any data from/to userspace through the
tty interface. Therefore a poll method is not needed.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is_pure_response() does "ntohl(var) & const" and then
essentially just tests whether the result is 0 or not; this can be done
more efficiently by computing "var & htonl(const)" instead and doing the
byte swap at compile time instead of run time.

This change slightly shrinks the compiled code; eg on x86-64 we save a
couple of bswapl instructions:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function                                     old     new   delta
t3_sge_intr_msix_napi                        544     536      -8

and this also has the pleasant side effect of fixing a sparse warning:

    drivers/net/cxgb3/sge.c:2313:15: warning: restricted degrades to integer
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.

Suspend/resume alredy added.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the power management support into the physical
abstraction layer.

Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.

In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.

Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).

Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These warning originate from 50014f1b (ne2: convert to
net_device_ops) which did drop those functions.

drivers/net/ne2.c:140: warning: 'ne_open' declared 'static' but never defined
drivers/net/ne2.c:141: warning: 'ne_close' declared 'static' but never defined
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ixgbe_init_interrupt_scheme() is called from ixgbe_resume().  Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the calls necessary to enable advanced error reporting for igb on
systems with AER enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update FW loading path to accomodate in-kernel images location
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add consistency in alloc_ring() parameter checking
to avoid potential memory leaks.
alloc_ring() callers are correct fo far.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix t3_eth_xmit() missing into the netdev_ops structure.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some print_mac -> %pM conversions got lost in some merge or another...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a regression (introduced by
"p54: more definitions form lmac_longbow.h and pda.h")

It turned out that the "ret" variable wasn't initialized and
this caused the following warnings/errors to appear:

wmaster1: failed to set TX queue parameters for queue 2
wmaster1: failed to set TX queue parameters for queue 3
wmaster1: failed to set TX queue parameters for queue 1
wmaster1: failed to set TX queue parameters for queue 0
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX channel width of the BSS can be obtained only after association.
In all cases, default to HT20 if HT is enabled, and set
chan width to HT40 only if the BSS supports it.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge core.c and base.c
Remove Antenna Diversity (unused now).
Remove unused chainmask handling code.
Comment, indentation scrub.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make firmware caching on startup optional, and make it default.

When the option is not selected and PM_SLEEP is configured, then
cache firmware in the suspend pm_notifier. This configuration saves
about 64k RAM in normal use, but can lead to a situation where the
driver is configured to use a different firmware.

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Retrieval of external firmware has been resolved, and should work with
the standard orinoco resume algorithm.

This fixes an issue where priv->hw_unavailable indicates the card is
ready when firmware has not been loaded.

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This refactorring will make it easier to share logic with Symbol
firmware.

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We would get an oops on RX on -ENOMEM by passing
NULL to the hardware on ath_rx_buf_link(). The oops
would look something like this:

ath_rx_tasklet+0x515/0x53b
ath9k_tasklet+0x48
tasklet_action
__do_softirq
irq_exit
do_IRQ

RIP: ath_rx_buf_link+0x3a

We correct this by handling the requeue directly on
the ath_rx_tasklet() and trying to allocate an skb
*prior* to sending up the last hardware processed
skb. If we run out of memory this gauranteees we have
skbs to work with while it simply drops new received
frames.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch brings the ath5k eeprom parsing code in sync with the work
done on ath_info by Nick Kossifidis and integrates the missing parts
based on the code of the Atheros Legacy HAL release.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the rate control only with the tx status of first
AMPDU of an aggregation. This patch fixes frequent drops
in throughput.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This instructs FH to increment the retry count of a packet when
it is brought from the memory to TX-FIFO to save transactions
during aggregation flow.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch configures correctly TX DMA channel. It is not
the same as TX queue.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apply same idiom as in 5000 introduced by
'iwlwifi: define firmware file name once'
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds base band calibration support.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves iwl_clear_stations_table into iwl-sta.c
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes the ad-hoc mode by
1) Removing redundant clear_stations_table which prevented generation of
beacons.
2) Setting assoc_id to 1. It was never set so preventing tx flow
in iwl3945_tx_skb.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configure the mac address in add_interface and clear it in
remove_interface so that users can change the mac address
to something other than the one in the eeprom.  Also avoid
setting it at attach time so that we won't ack packets
until fully set up.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>