[Description]
This is for HW negative stress testing use.
force reset the dispclk and dppclk even the same clock already set in HW.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

id_to_offset does not point to the same reg offset that offset_to_id checks for,
causing unintended asserts
Signed-off-by: NMurton Liu <murton.liu@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

add dc_set_clock
add dc_get_clock

this is for testing and diagnostics to get/set DPPCLK and DISPCLK.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.

[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: NDerek Lai <Derek.Lai@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Implementation of stereo mux register is complete, but unused. Need to
call functions to write relevant configs.

[How]
Add function to write stereo config for enable/disable case and call in
stereo control interface.
Signed-off-by: NMurton Liu <murton.liu@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Alpha could be improperly applied (only affecting half the
frame) for some source pixel formats.

[How]
Change how alpha is enabled in MPC/DPP LB and change the
bottom plane blend mode in MPC.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For clarity, save the use_pitch_c logic to a bool
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NEric Bernstein <eric.bernstein@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add this register for future use
Signed-off-by: NNevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: NVitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
bypass CM block and MPC ogam for debug or triage use.

[How]
create a new flag cm_bypass_mode, which will set both CM_CONTROL
and MPCC_OGAM_MODE to bypass when set to 1.
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
Number of 3DLUT's in MPC are not equal to number of pipes.
Resource management is required.
Activate on FPGA entire tm solution  which includes
the following :hdr multiplier, shaper, 3dlut.
Signed-off-by: NVitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NGary Kattan <Gary.Kattan@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We want a debug option to disable timing sync for testing.

[How]
New dc debug option that must be false to call program_timing_sync
Signed-off-by: NJoshua Aberback <joshua.aberback@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
As a fail-safe, in case 'set FEC_READY' DPCD write fails, a HW shadow
register should be cleared and the internal FEC stat should be set to
'not ready'. This is to make sure HW settings will be consistent with
FEC_READY state on the RX.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NJoshua Aberback <Joshua.Aberback@amd.com>
Acked-by: NChris Park <Chris.Park@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]

1. Stack usage is pretty high as fixed31_32 struct is 8 bytes and we
have functions with >30 vars on the stack.

2. Optimize gamma calculation by reducing number of calls to
dc_fixpt_pow Our X points are divided into 32 regions wth 16 pts each.
Each region is 2x the previous, meaning x[i] = 2*x[i-16] for i>=16.
Using (2x)^gamma = 2^gamma * x^gamma, we can recursively compute powers
of gamma, we just need first 16 pts to start it up. dc_fixpt_pow() is
expensive, it computes x^y by doing exp(y*logx) Exp is done by Taylor
series approximation, and log by Newton-like approximation that also
uses exp internally. In short, it's significantly heavier than
run-of-the-mill addition/subtraction/multiply.
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.

[How]
Put back proper front end power off sequence
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Acked-by: NTony Cheng <Tony.Cheng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Right now we FEC_READY is set only before the final link training,
i.e. at mode set time. This means FEC_READY won't be set when doing
link training as a response to HPD. It also fails UCD400 FEC test in
DP compliance.

[how]
Move FEC_READY setup to link training.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NAbdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use helper to determine if HDMI signal when processing avmute.
Signed-off-by: NEric Bernstein <eric.bernstein@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Logic & structures for generic regs does not exist in DC currently.

[How]
Implement register masks/shifts and relevant functions for generic mux,
similar to existing HPD and DDC objects.

V2: fix includes for kalloc/free (Alex)
Signed-off-by: NMurton Liu <murton.liu@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NJoshua Aberback <Joshua.Aberback@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending

[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.

[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: NFatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: NJoshua Aberback <Joshua.Aberback@amd.com>
Acked-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
We initialize pp_smu twice

[how]
Remove second initialization of pp_smu
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
dcn20_clk_mgr_construct was not initializing pp_smu, and PME call gets
filtered out by the null check

[how]
initialize pp_smu dcn20_clk_mgr_construct
Signed-off-by: NSu Sung Chung <Su.Chung@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.

[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: NTai Man <taiman.wong@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
link_stream is never NULL here as we've dereferenced it a couple lines before
and have done so for a couple months now.

[How]
- Drop the NULL check.
- Initialize where we know link_stream is non-NULL
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Description]
Do not fill Null packet in the blank period for new packet gen
This is based on HW IP team recommended default setting change.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.

[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: NZi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When we recover from hang, we do not want to skip the audio enable call.

[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
DSC should be powered-on only on as-needed basis, i.e. if the mode
requires it

[how]
Loop over all the DSCs at driver init time and power-gate each
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NNevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Current default is sufficient for a flag that does not change.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00

[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: NDerek Lai <Derek.Lai@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
A hubp pointer was being passed to DCN1 functions, which
expect the enclosing structure (for the purpose of container_of macros)
to be dcn10_hubp, but the actual type was dcn20_hubp.

[How]
Copy existing DCN1 functions and alter them slightly for use with
dcn20_hubp.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Before accessing it's vtable, check that stream_encoder is non-null.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NEric Bernstein <Eric.Bernstein@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Need to implement register programming for HDR dynamic
metadata transmission and tests.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NEric Bernstein <Eric.Bernstein@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.

[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: NSivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We need to check the pipe crc source through debugfs for bypass mode test.

[How]
add implementation of amdgpu_dm_crtc_get_crc_sources and hook into drm_crtc
callback get_crc_sources.
Signed-off-by: NDingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We need to compare DPRX CRCs with framebuffer CRCs for digital bypass mode.

[How]
Hook into DRM to grab DP receiver CRCs through drm_dp_start_crc.
Signed-off-by: NDingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.

[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.

v2: fix include for udelay (Alex)
Signed-off-by: NJulian Parkin <julian.parkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Specifically to one panel,
TCON is able to accept active video signal quickly, but
the Source Driver requires 2-3 frames of extra time.

It is a Panel issue since TCON needs to take care of
all Sink requirements including Source Driver. But in
this case it does not.

Customer is asking to add fixed T7 delay as panel
workaround.

[How]
Add monitor specific patch to add T7 delay
Signed-off-by: NAnthony Koo <anthony.koo@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>