We're talking about Spread Spectrum Clocks here, thus SSC.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So WARN in case they're not. It also does not make any sense to
wait_for_vblank at this point.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And also properly wait for its idle bit.

You may notice that DDI_BUF_CTL is enabled in .enable but disabled in
.post_disable instead of .disable. Yes, the mode set sequence is not
exactly symmetrical, but let's assume the spec is correct unless we
can prove it's wrong.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Introduced in commit 87f8020e:
  drm/i915: implement WaDisableEarlyCull for VLV and IVB

Notice that the original patch sent to the mailing list did not
include the Haswell chunk, it was added later.

The bit set by the commit does not exist on Haswell machines (at least
that's what the documentation says). Also, the commit gives me a GPU
hang every time we're loading the driver. So let's revert the Haswell
chunk, making the patch do only what its title actually says.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just set the only bit we need, everything else is either ignored on
HDMI or should be set to zero.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Problems with the previous code:
  - HDMI just uses WRPLL1 for everything, so dual head cases might not
    work sometimes.
  - At encoder->mode_set we just write the PLL register without doing
    any kind of check (e.g., check if the PLL is already being used).
  - There is no way to fail and return error codes at
    encoder->mode_set.
  - We write to PORT_CLK_SEL at mode_set and we never disable it.
  - Machines hang due to wrong clock enable/disable sequence.

So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
  - Check PLL availability at ironlake_crtc_mode_set.
  - Try to use both WRPLLs.
  - Check if PLLs are used before actually trying to use them, and
    properly fail with error messages.
  - Enable/disable PORT_CLK_SEL at the right place.
  - Add some WARNs to check for bugs.

The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's a copy of ironlake_set_pipeconf with 2 differences:
  - There is no BPC field to set.
  - The interlaced mask is now 2 bits instead of 3.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On ironlake_crtc_mode_set, WARN if not using IBX or CPT.

On haswell_crtc_mode_set, only run IBX/CPT code on IBX/CPT. I am still
not sure whether IBX/CPT will be possible with a Haswell CPU, so leave
the code there for now and put a WARN in case we spot it.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's just a copy of ironlake_crtc_mode_set.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously we were enabling it at mode_set but never disabling. Let's
follow the mode set sequence.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And the right time is exactly after/before changing PIPE_CONF. See the
documentation about the mode set sequence.

This code is not inside any encoder-specific callback because
DDI_FUNC_CTL is part of the pipe, so it is used by all encoders.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Right now, we're trying to enable LCPLL at every mode set, but we're
never disabling it. Also, we really don't want to be disabling LCPLL
since it requires a very complex disable/enable sequence. This
register should really be set by the BIOS and we shouldn't be touching
it. Still, let's try to check its value and print some errors in case
we find something wrong. We're also adding intel_ddi_get_cdclk_freq
which will be used later in other places.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By using round_jiffies() we can align the wakeup of our worker to the
nearest second in order to batch wakeups and reduce system load, which
is useful for unimportant coarse tasks like our retire_requests.

v2: round_jiffies_relative() already returns the relative timeout value,
so no need to incorrectly perform the subtraction twice. The timer
interface still leaves the possibility for the value of jiffies to
change be we program the timer.
Suggested-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

round_jiffies() aligns the wakeup time to the nearest second in order to
batch wakeups and reduce system load, which is useful for unimportant
coarse timers like our hangcheck.

v2: round_jiffies_relative() returns the relative jiffie value, whereas
we need the absolute value for the timer.
Suggested-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This workaround is only valid for IVB and VLV and the write triggers an
error on HSW.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanonI@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For the next person that checks these kind of things, without having to
dig up the register definition.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove duplicated include.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There's is another register (a read only, so no harm done) at 0x42020 on
Haswell GPUs. Let's just remove the write from the copy&paste that
introduced haswell_init_clock_gating().

A note for the interested reader, it does seem we have a duplication of
the 0x42020 register definition, hence the removal of 2 writes. That
duplication could be the object of a later patch.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Workaround for a culling optimization.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Also apply to haswell, spotted by Damien.]
Reviewed-by: N"Lespiau, Damien" <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

References: https://bugs.freedesktop.org/show_bug.cgi?id=50250Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I'm official fed up with the yelling and useless indirection.

Let it burn!
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Version 2: call intel_set_pipe_timings from both i9xx_crtc_mode_set
and ironlake_crtc_mode_set, instead of just ironlake, as requested by
Daniel Vetter.

The problem caused by calling this function from i9xx_crtc_mode_set
too is that now on i9xx we write to PIPESRC before writing to DSPSIZE
and DSPPOS. I could not find any evidence in our documentation that
this won't work, and the docs actually say the pipe registers should
be set before the plane registers.

Version 3: don't remove pipeconf bits on i9xx_crtc_mode_set.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make it easier to track backlight set requests coming through ASLE instead
of the driver's own backlight sysfs interface. We've had enough of
backlight issues to warrant some extra debug logs in the area.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fixed correct min, max vco limits and dip ctl reg
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Eventhough Valleyview display block is derived from Cantiga, VLV
supports eDP. So, added eDP checks in i9xx_crtc_mode_set path.

v2: use different DPIO_DIVISOR values for VGA, DP and eDP
v3: fix DPIO value calculation to use same values for all display
interfaces
v4: removed unconditional enabling of 6bpc dithering based on comments
from Daniel & Jani Nikula. Also changed the display enabling order to
force eDP detection first.
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In valleyview voltageswing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric.

Cleaned up DPLL calculations for Valleyview to support multi display
configurations.

v2: Based on Daniel's feedbacak, moved crt hotplug detect work around as separate
patch. Also moved i9xx_update_pll_dividers to i8xx_update_pll and
i9xx_update_pll.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: drop spurious whitespace changes.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

m n tu register offset has changed in Valleyview. Also fixed DP limit
frequencies.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added DPIO data lane register definitions for Valleyview
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fixed SDVOB and SDVOC bit definitions for Valleyview.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Set hrawclk to 200 MHz and aux divider clock to 100 MHz for Valleyview.
This enables the aux transactions in Valleyview.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To match IVB.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Note with a comment anything newer than DP 1.1a.

Obviously this needs some work still...
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If there's no downstream device, DPCD success is good enough.  If
there's a hotplug-capable downstream device, count the number of
connected sinks in DP_SINK_STATUS and return success if it's non-zero.
Otherwise, probe DDC and report appropriately.

v2: Check DP_SINK_STATUS instead of something unrelated to sink status.
Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Fix parenthesis mismatch, spotted by Jani Nikula
Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Fixup merge conflict and MAX_DOWNSTREAM #define as spotted by
Jani.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Sources: DP, eDP, and DP interop specs, and a VESA slideshow about DP
1.2 for the MST bits.
Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The last patches moved a lot of code from ironlake_crtc_mode_set to
sub-functions, so these variables became useless. You could get
warnings by enabling -Wunused-but-set-variable.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Too many lines just to compute the value of a single variable, so
move this to its own function.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The set_m_n code was spread all over the mode_set function.

Version 2:
Don't set the DP M/N registers on ironlake_set_m_n. Daniel Vetter has
plans to add some encoder-specific callbacks. Also, on this version we
don't change the order we're writing the registers, making the code
change safer.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>