While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.

This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* use irq_handler_t where appropriate

* no need to use 'irq' function arg, its already stored in a data struct

* rename irq handler 'irq' argument to 'dummy', where the function
  has been analyzed and proven not to use its first argument.

* remove always-false "dev_id == NULL" test from irq handlers

* remove pointless casts from void*

* declance: irq argument is not const

* add KERN_xxx printk prefix

* fix minor whitespace weirdness
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.

The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.

This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().

Unfortunately, this trips up the semaphore used here in the Intel
drivers.  If you hit this case, when you try to bring the interface
back up it won't enable interrupts.  A reload of the driver module
fixes it of course.

So what we do is make sure all the sequences now go:

	napi_disable();
	atomic_set(&adapter->irq_sem, 0);
	*_irq_disable();

which makes sure the counter is always in the correct state.

Reported by Robert Olsson.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a regression added by changeset
53e52c72 ("[NET]: Make ->poll()
breakout consistent in Intel ethernet drivers.")

As pointed out by Jesse Brandeburg, for three of the drivers edited
above there is breakout logic in the *_clean_tx_irq() code to prevent
running TX reclaim forever.  If this occurs, we have to elide NAPI
poll completion or else those TX events will never be serviced.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>

This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.

Now they will all break out when the amount of RX work done is less
than 'budget'.

At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this).  But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NAuke Kok <auke-jan.h.kok@intel.com>

Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.

Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make strings const if possible, and fix includes so forward definitions
are seen.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.

This version of the driver is largely the same as the last release:

  * Driver uses a single RX and single TX queue, each using 1 MSI-X
  irq vector.
  * Driver runs in NAPI mode only
  * Driver is largely multiqueue-ready (TM)

Changes since 20070803:
  * removed wrappers for hardware functions
  * incorporated e1000e-style HW api reorganization code
  * sparse/checkpatch cleanups, namespace cleanups
  * driver prints out extra debugging information at load time
    identifying adapter board number, mac, phy types
  * removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
  * driver update to 1.1.18
  * removed ixgbe.txt which contained no useful info anymore

[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NAyyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>