On gen11 writing to read only ppgtt page causes a gpu hang.
This behaviour is different than with previous gen where
read only ppgtt access is supported. On those, the write
is just dropped without visible side effects.

Disable ro ppgtt support on gen11 until a solution can
be found to bring it into line with its predecessors.

References: HSDES#1807136187
References: https://bugzilla.freedesktop.org/show_bug.cgi?id=108569
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190411083034.28311-1-mika.kuoppala@linux.intel.com

As i915_requests are put into an RCU-freelist, they may get reused
before debugobjects notice them as being freed. On cleanup, explicitly
call i915_sw_fence_fini() so that the debugobject is properly tracked.
Reported-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: b7404c7e ("drm/i915: Bump ready tasks ahead of busywaits")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190411122445.20060-1-chris@chris-wilson.co.uk

No point in duplicating all this code when we can just
use a variable to hold the output bpp (the only thing
that differs between the two branches).

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.comk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326144903.6617-2-ville.syrjala@linux.intel.comReviewed-by: NManasi Navare <manasi.d.navare@intel.com>

6bpc is only legal for RGB and RAW pixel encodings. For the rest
the minimum is 8bpc. Set our lower limit accordingly.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326142556.21176-6-ville.syrjala@linux.intel.comReviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

Now when we can support variable csb fifo sizes, disable legacy mode.
By disabling legacy we hope to get better hw testing coverage by
assuming everyone else have switched over.

v2: rebase

References: https://bugs.freedesktop.org/show_bug.cgi?id=110338
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Kelvin Gardiner <kelvin.gardiner@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405204657.12887-2-chris@chris-wilson.co.uk

Make csb entry count variable in preparation for larger
CSB status FIFO size found on gen11+ hardware.

v2: adapt to hwsp access only (Chris)
    non continuous mmio (Daniele)
v3: entries (Chris), fix macro for checkpatch
v4: num_entries (Chris)
v5: consistency on num_entries

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405204657.12887-1-chris@chris-wilson.co.uk

With gen11 the interrupt registers are shared between 2 engines,
with Engine1 instance being upper word and Engine0 instance being
lower. Annoyingly gen11 selected the pm interrupts to be in the
Engine1 instance.

Rectify the situation by shifting the access accordingly,
based on gen.

v2: comments, warn on overzealous rps_events

Bugzilla: https://bugzilla.freedesktop.org/show_bug.cgi?id=108059
Testcase: igt/i915_pm_rps@min-max-config-loaded
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410105923.18546-6-mika.kuoppala@linux.intel.com

There is no video turbo mode for gen11, so don't set it.

v2: inline (Chris)
v3: brackets (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410132436.23679-1-mika.kuoppala@linux.intel.com

Enable media sampler powergate as recommended.

v2: use REG_BIT (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410105923.18546-3-mika.kuoppala@linux.intel.com

On gen11 the recommended rc6 threshold differs from previous
gens, apply it. Move the write to a correct spot in sequence.

v2: do write in 2b, fix bspec ref (Michal)

Bspec: 33149
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410105923.18546-2-mika.kuoppala@linux.intel.com

In order not to inflate gen9 rc6 enabling sequence with
gen11 specifics, use a separate function for it.
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410105923.18546-1-mika.kuoppala@linux.intel.com

Consider two tasks that are running in parallel on a pair of engines
(vcs0, vcs1), but then must complete on a shared engine (rcs0). To
maximise throughput, we want to run the first ready task on rcs0 (i.e.
the first task that completes on either of vcs0 or vcs1). When using
semaphores, however, we will instead queue onto rcs in submission order.

To resolve this incorrect ordering, we want to re-evaluate the priority
queue when each of the request is ready. Normally this happens because
we only insert into the priority queue requests that are ready, but with
semaphores we are inserting ahead of their readiness and to compensate
we penalize those tasks with reduced priority (so that tasks that do not
need to busywait should naturally be run first). However, given a series
of tasks that each use semaphores, the queue degrades into submission
fifo rather than readiness fifo, and so to counter this we give a small
boost to semaphore users as their dependent tasks are completed (and so
we no longer require any busywait prior to running the user task as they
are then ready themselves).

v2: Fixup irqsave for schedule_lock (Tvrtko)

Testcase: igt/gem_exec_schedule/semaphore-codependency
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190409152922.23894-1-chris@chris-wilson.co.uk

On resume, we know that the only pinned contexts in danger of seeing
corruption are the kernel context, and so we do not need to walk the
list of all GEM contexts as we tracked them on each engine.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410190120.830-1-chris@chris-wilson.co.uk

Currently we use force_dsc_enable to force DSC from IGT, but
we dont expose this value to userspace through debugfs.
This patch exposes this through the same dsc_fec_support
debugfs node per connector so that we can restore its value
back after the tests are completed.
Suggested-by: NImre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405224821.32435-1-manasi.d.navare@intel.com

There is a chance we can see spurious interrupts in live
now. We have more engines enabled and that with more elaborate
access patterns with pm and display, increases the chances
hardware just makes a social call, without anything to work on.

Remove the error as we have tests to actually probe if
we really miss interrupt, instead of getting spurious ones.

Note that now we do write to intr_dw even with a zero
value. This is considered advantegous as the write
is an ack that sw is done.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410132124.21795-2-mika.kuoppala@linux.intel.com

Unlike previous gens, we already hold the irq_lock on
entering the rps handler so we can't use it as it is.

Make a gen11 specific rps interrupt handler without
locking.

v2: return early (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410132124.21795-1-mika.kuoppala@linux.intel.com

snd_hdac_display_power() doesn't handle the concurrent calls carefully
enough, and it may lead to the doubly get_power or put_power calls,
when a runtime PM and an async work get called in racy way.

This patch addresses it by reusing the bus->lock mutex that has been
used for protecting the link state change in ext bus code, so that it
can protect against racy display state changes.  The initialization of
bus->lock was moved from snd_hdac_ext_bus_init() to
snd_hdac_bus_init() as well accordingly.

Testcase: igt/i915_pm_rpm/module-reload #glk-dsi
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/s5h8swiunph.wl-tiwai@suse.de

Commit 7769db58 ("drm/i915/dp: optimize eDP 1.4+ link config fast
and narrow") started to optize the eDP 1.4+ link config, both per spec
and as preparation for display stream compression support.

Sadly, we again face panels that flat out fail with parameters they
claim to support. Revert, and go back to the drawing board.

v2: Actually revert to max params instead of just wide-and-slow.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109959
Fixes: 7769db58 ("drm/i915/dp: optimize eDP 1.4+ link config fast and narrow")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.0+
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Tested-by: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Tested-by: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Tested-by: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405075220.9815-1-jani.nikula@intel.com

Re-enable clock gating of DDI clocks.

v2: Fix the default ddi clk state for mipi-dsi (Imre)

Fixes: 1026bea0 ("drm/i915/icl: Ungate DSI clocks")
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-2-git-send-email-vandita.kulkarni@intel.com

IO enable sequencing needs ddi clocks enabled.
These clocks will be gated at a later point in
the enable sequence.

v2: Fix the commit header (Uma)
v3: Remove the redundant read (Ville)

Fixes: 949fc52a ("drm/i915/icl: add pll mapping for DSI")
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-1-git-send-email-vandita.kulkarni@intel.com

Circumvent the dance we currently perform to find the preempt_client and
lookup its HW context for this engine, as we know we have already pinned
the preempt_context on the engine.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190408091728.20207-15-chris@chris-wilson.co.uk

A couple of machines in the farm show quite frequent errors in the
powerwells not being released. Either there is an external agent
interferring with the powerwells, or the powerwell doesn't quite behave
as we anticipate -- either way, the test is not reliable enough to be
enabled by default in CI. It has served its immediate purpose in
providing coverage as we made tweaks to forcewake, so keep it available
for future testing.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110210Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407192649.14750-1-chris@chris-wilson.co.uk

This interlaced mode restriction applies to all gens, not only to
Haswell.

Also while at it updating the debug message to.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-4-jose.souza@intel.com

Even when driver is reloaded and hits this scenario the PSR mutex
should be initialized, otherwise reading PSR debugfs status will
execute mutex_lock() over a mutex that was not initialized.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-3-jose.souza@intel.com

PSR support for VLV and CHV was dropped in commit ce3508fd
("drm/i915/psr: Nuke PSR support for VLV and CHV") so no need to keep
this registers around.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-2-jose.souza@intel.com

Turn out it is not a DMC bug it is actually a HW one, so this
workaround will be needed for current gens, lets update the comment
and remove the FIXME.

BSpec: 7723
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-1-jose.souza@intel.com

The timeline is strictly ordered, so by inserting the timeline->barrier
request into the timeline->last_request it naturally provides the same
barrier. Consolidate the pair of barriers into one as they serve the
same purpose.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190408091728.20207-4-chris@chris-wilson.co.uk

In order to avoid the malloc inside i915_globals_park() occurring
underneath a lock connected to the shrinker (thus causing circular
lockdeps warnings), move the rcu_worker to a global.

<4> [39.085073] ======================================================
<4> [39.085273] WARNING: possible circular locking dependency detected
<4> [39.085552] 5.1.0-rc3-CI-Trybot_4088+ #1 Tainted: G     U
<4> [39.085752] ------------------------------------------------------
<4> [39.085949] kswapd0/32 is trying to acquire lock:
<4> [39.086121] 00000000004b5f91 (wakeref#3){+.+.}, at: intel_engine_pm_put+0x1b/0x40 [i915]
<4> [39.086493]
but task is already holding lock:
<4> [39.086682] 00000000dd009a9a (fs_reclaim){+.+.}, at: __fs_reclaim_acquire+0x0/0x30
<4> [39.086910]
which lock already depends on the new lock.

<4> [39.087139]
the existing dependency chain (in reverse order) is:
<4> [39.087356]
-> #2 (fs_reclaim){+.+.}:
<4> [39.087604]        fs_reclaim_acquire.part.24+0x24/0x30
<4> [39.087785]        kmem_cache_alloc_trace+0x2a/0x290
<4> [39.087998]        i915_globals_park+0x22/0xa0 [i915]
<4> [39.088478]        idle_work_handler+0x1df/0x220 [i915]
<4> [39.089016]        process_one_work+0x245/0x610
<4> [39.089447]        worker_thread+0x37/0x380
<4> [39.089956]        kthread+0x119/0x130
<4> [39.090374]        ret_from_fork+0x3a/0x50
<4> [39.090868]
-> #1 (wakeref#4){+.+.}:
<4> [39.091569]        __mutex_lock+0x8c/0x960
<4> [39.092054]        atomic_dec_and_mutex_lock+0x33/0x50
<4> [39.092521]        intel_gt_pm_put+0x1b/0x40 [i915]
<4> [39.093047]        intel_engine_park+0xeb/0x1d0 [i915]
<4> [39.093514]        __intel_wakeref_put_once+0x10/0x30 [i915]
<4> [39.094062]        i915_request_retire+0x477/0xaf0 [i915]
<4> [39.094547]        ring_retire_requests+0x86/0x160 [i915]
<4> [39.095110]        i915_retire_requests+0x58/0xc0 [i915]
<4> [39.095587]        i915_gem_wait_for_idle.part.22+0xb2/0xf0 [i915]
<4> [39.096142]        switch_to_kernel_context_sync+0x2a/0x70 [i915]
<4> [39.096633]        i915_gem_init+0x59c/0x9c0 [i915]
<4> [39.097174]        i915_driver_load+0xd96/0x1880 [i915]
<4> [39.097640]        i915_pci_probe+0x29/0xa0 [i915]
<4> [39.098145]        pci_device_probe+0xa1/0x120
<4> [39.098607]        really_probe+0xf3/0x3e0
<4> [39.099031]        driver_probe_device+0x10a/0x120
<4> [39.099599]        device_driver_attach+0x4b/0x50
<4> [39.100033]        __driver_attach+0x97/0x130
<4> [39.100525]        bus_for_each_dev+0x74/0xc0
<4> [39.100954]        bus_add_driver+0x13f/0x210
<4> [39.101441]        driver_register+0x56/0xe0
<4> [39.101891]        do_one_initcall+0x58/0x2e0
<4> [39.102319]        do_init_module+0x56/0x1ea
<4> [39.102805]        load_module+0x2701/0x29e0
<4> [39.103231]        __se_sys_finit_module+0xd3/0xf0
<4> [39.103727]        do_syscall_64+0x55/0x190
<4> [39.104153]        entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4> [39.104736]
-> #0 (wakeref#3){+.+.}:
<4> [39.105437]        lock_acquire+0xa6/0x1c0
<4> [39.105923]        __mutex_lock+0x8c/0x960
<4> [39.106345]        atomic_dec_and_mutex_lock+0x33/0x50
<4> [39.106897]        intel_engine_pm_put+0x1b/0x40 [i915]
<4> [39.107375]        i915_request_retire+0x477/0xaf0 [i915]
<4> [39.107930]        ring_retire_requests+0x86/0x160 [i915]
<4> [39.108412]        i915_retire_requests+0x58/0xc0 [i915]
<4> [39.108934]        i915_gem_shrink+0xd8/0x5b0 [i915]
<4> [39.109431]        i915_gem_shrinker_scan+0x59/0x130 [i915]
<4> [39.109884]        do_shrink_slab+0x131/0x3e0
<4> [39.110380]        shrink_slab+0x228/0x2c0
<4> [39.110810]        shrink_node+0x177/0x460
<4> [39.111317]        balance_pgdat+0x239/0x580
<4> [39.111743]        kswapd+0x186/0x570
<4> [39.112221]        kthread+0x119/0x130
<4> [39.112641]        ret_from_fork+0x3a/0x50
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190408091728.20207-3-chris@chris-wilson.co.uk

Replace the WARN with a simple if() + error message to squech the sparse
warning that entire wait_for() macro was being stringified:

drivers/gpu/drm/i915/intel_guc_submission.c:658:9: error: too long token expansion
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190408091728.20207-2-chris@chris-wilson.co.uk

We can unconditionally release the power references during encoder
disabling. The references for each port used by the encoder are
guaranteed to be enabled at this point.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405153657.20921-2-imre.deak@intel.com

Push getting the reference for the encoders' power domains into the
encoder get_power_domains() hook instead of doing this from the caller.
This way the encoder can store away the corresponding wakerefs.

This fixes the DSI encoder disabling, which didn't release these
power references it acquired during HW state readout.

Note that longtime ownership for the corresponding wakerefs can be thus
acquired / released in two ways. Nevertheless there is always only one
owner for them:

After HW readout (booting/system resume):
- encoder->get_power_domains() acquires
- encoder->disable*() releases

After a modeset (calling intel_atomic_commit()):
- encoder->enable*() acquires
- encoder->disable*() releases

* can be any of the encoder enable/disable hooks.

v2:
- Check that the DSI io_wakerefs are unset both during encoder HW
  readout and enabling. (Chris)

Fixes: 0e6e0be4 ("drm/i915: Markup paired operations on display power domains")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407124655.31536-1-imre.deak@intel.com

While transitioning to having better clarity between the modules, it's
desirable to have the function name prefixes reflect the
module. Functions in intel_foo.c should be prefixed intel_foo_.

Expose only one CDCLK init/uninit function from intel_cdclk.c instead of
one per platform. Obviously this adds one "unnecessary" if ladder within
the entry points. However it should be considered more of a CDCLK
implementation detail how this is done per platform, instead of exposing
the fact. In other words, abstract the CDCLK module better.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f63ed6e129098a32c63735be6cffa4756e7947af.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c128d7be3f621391e571e86b03f302f3ffd0ed2b.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/679c857a1933ee3d0706f978ab05ca880cd30a00.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1ccf9000ad33b895aea06be41053a5b7bac8459e.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5d54d02cf7b7bfe3f78ed60d28534c5726371af3.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f44c21e3d154e47233ebef4267ce1a924fa38df7.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b106b21ef11ff7fc34537b2c029a1332c8573fcc.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.

v2: revert intel_plane_destroy_state() movement within intel_atomic_plane.c
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fd56c1cbba22b9f195ad944d79f7977423b2b533.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/357856c31e309f0af8eed0d800623a5253ff3a37.1554461791.git.jani.nikula@intel.com