As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.

Change the order to close this race condition.

Fixes: 92571a1a ("lan78xx: Connect phy early")
Reported-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devlink maintains packets and bytes statistics for each trap. Since
eth_type_trans() was called to set the skb's protocol, the data pointer
no longer points to the start of the packet and the bytes accounting is
off by 14 bytes.

Fix this by pushing the skb's data pointer to the start of the packet.

Fixes: b5ce611f ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: NAlex Kushnarov <alexanderk@mellanox.com>
Tested-by: NAlex Kushnarov <alexanderk@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.

It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.

Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.

The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.

Fixes: 484bfa15 ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.

This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.

Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When commit 28b2e0d2 ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().

However, once commit 88d6272a ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().

This commit removes that initialization to restore the proper
functionality.

Fixes: 88d6272a ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.

Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.

This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.

Fixes: 9d162ed6 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.

To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.

Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.

Fix the warning (and possible bug) from sparse:

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17:    expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17:    got struct mac_device_info *hw
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.

Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.

Fixes: 1fa0f68c ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: NFlorin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.

v2: fix syntax error
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

disable ptp_ref_clk in suspend flow, and enable it in resume flow.

Fixes: f573c0b9 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: NBiao Huang <biao.huang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.

The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.

This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.

Fixes: 88d6272a ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Reviewed-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure res does not contain random value if the call to
sr_read_cmd fails for some reason.

Reported-by: syzbot+f1842130bbcfb335bac1@syzkaller.appspotmail.com
Signed-off-by: NValentin Vidic <vvidic@valentin-vidic.from.hr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.

Fixes: aa09677c ("net: bcmgenet: add MDIO routines")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tc_flow_parsers is not used outside of the driver, so
make it static to avoid the following sparse warning:

drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c:516:3: warning: symbol 'tc_flow_parsers' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpdma_chan_split_pool() function is not used outside of
the driver, so make it static to avoid the following sparse
warning:

drivers/net/ethernet/ti/davinci_cpdma.c:725:5: warning: symbol 'cpdma_chan_split_pool' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7f683b92 ("i825xx: switch to switch to dma_alloc_attrs")
switched dma allocation over to dma_alloc_attr, but didn't convert
the SNI part to request consistent DMA memory. This broke sni_82596
since driver doesn't do dma_cache_sync for performance reasons.
Fix this by using different DMA_ATTRs for lasi_82596 and sni_82596.

Fixes: 7f683b92 ("i825xx: switch to switch to dma_alloc_attrs")
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for NXP SJA1105 series Ethernet switch support.
It uses an expilict block comment for the SPDX License
Identifier.

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NNishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original design, mtk_phy_connect function will set ge_mode=1
if phy-mode is GMII(PHY_INTERFACE_MODE_GMII) and then set the correct
ge_mode to ETHSYS_SYSCFG0 register. This logic was broken after apply
mediatek PHYLINK patch(Fixes tag), the new mtk_mac_config function will
not set ge_mode=1 for GMII mode hence the final ETHSYS_SYSCFG0 setting
will be incorrect for mt7629 GMII mode. This patch add the missing logic
back to fix it.

Fixes: b8fc9f30 ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: NMarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects the SPDX License Identifier style
in header files related to Cavium Ethernet drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NNishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for Microchip KSZ series switch support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NNishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NET_VENDOR_BROADCOM is intended to control a kconfig menu only.
It should not have anything to do with code generation.
As such, it should not select DIMLIB for all drivers under
NET_VENDOR_BROADCOM.  Instead each driver that needs DIMLIB should
select it (being the symbols SYSTEMPORT, BNXT, and BCMGENET).

Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907021810220.13058@ramsan.of.borg/

Fixes: 4f75da36 ("linux/dim: Move implementation to .c files")
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Tal Gilboa <talgi@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phydev->dev_flags is entirely dependent on the PHY device driver which
is going to be used, setting the internal GENET PHY revision in those
bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver
being used.

Fixes: 487320c5 ("net: bcmgenet: communicate integrated PHY revision to PHY driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macvlan and multicast handling is now mixed up.
The explicit issue is that macvlan interface gets broken (no traffic)
after clearing MULTICAST flag on the real interface.

We now do separate logic and consider both ALLMULTI and MULTICAST
flags on the device.

Fixes: 11ba961c ("net: aquantia: Fix IFF_ALLMULTI flag functionality")
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Individual descriptors on LRO TCP session should be checked
for CRC errors. It was discovered that HW recalculates
L4 checksums on LRO session and does not break it up on bad L4
csum.

Thus, driver should aggregate HW LRO L4 statuses from all individual
buffers of LRO session and drop packet if one of the buffers has bad
L4 checksum.

Fixes: f38f1ee8 ("net: aquantia: check rx csum for all packets in LRO session")
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

>From HW specification to correctly reset HW caches (this is a required
workaround when stopping the device), register bit should actually
be toggled.

It was previosly always just set. Due to the way driver stops HW this
never actually caused any issues, but it still may, so cleaning this up.

Fixes: 7a1bb494 ("net: aquantia: fix potential IOMMU fault after driver unbind")
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chip temperature is a two byte word, colocated internally with cable
length data. We do all readouts from HW memory by dwords, thus
we should clear extra high bytes, otherwise temperature output
gets weird as soon as we attach a cable to the NIC.

Fixes: 8f894011 ("net: aquantia: add infrastructure to readout chip temperature")
Tested-by: NHolger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(kvalo: cherry picked from commit 1340cc63 in
wireless-drivers-next to wireless-drivers as this a frequently reported
regression)

Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.

Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037

Fixes: 4504f0e5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In nsim_fib_init(), if register_fib_notifier failed, nsim_fib_net_ops
should be unregistered before return.

In nsim_fib_exit(), unregister_fib_notifier should be called before
nsim_fib_net_ops be unregistered, otherwise may cause use-after-free:

BUG: KASAN: use-after-free in nsim_fib_event_nb+0x342/0x570 [netdevsim]
Read of size 8 at addr ffff8881daaf4388 by task kworker/0:3/3499

CPU: 0 PID: 3499 Comm: kworker/0:3 Not tainted 5.3.0-rc7+ #30
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Workqueue: ipv6_addrconf addrconf_dad_work [ipv6]
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xa9/0x10e lib/dump_stack.c:113
 print_address_description+0x65/0x380 mm/kasan/report.c:351
 __kasan_report+0x149/0x18d mm/kasan/report.c:482
 kasan_report+0xe/0x20 mm/kasan/common.c:618
 nsim_fib_event_nb+0x342/0x570 [netdevsim]
 notifier_call_chain+0x52/0xf0 kernel/notifier.c:95
 __atomic_notifier_call_chain+0x78/0x140 kernel/notifier.c:185
 call_fib_notifiers+0x30/0x60 net/core/fib_notifier.c:30
 call_fib6_entry_notifiers+0xc1/0x100 [ipv6]
 fib6_add+0x92e/0x1b10 [ipv6]
 __ip6_ins_rt+0x40/0x60 [ipv6]
 ip6_ins_rt+0x84/0xb0 [ipv6]
 __ipv6_ifa_notify+0x4b6/0x550 [ipv6]
 ipv6_ifa_notify+0xa5/0x180 [ipv6]
 addrconf_dad_completed+0xca/0x640 [ipv6]
 addrconf_dad_work+0x296/0x960 [ipv6]
 process_one_work+0x5c0/0xc00 kernel/workqueue.c:2269
 worker_thread+0x5c/0x670 kernel/workqueue.c:2415
 kthread+0x1d7/0x200 kernel/kthread.c:255
 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352

Allocated by task 3388:
 save_stack+0x19/0x80 mm/kasan/common.c:69
 set_track mm/kasan/common.c:77 [inline]
 __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:493
 kmalloc include/linux/slab.h:557 [inline]
 kzalloc include/linux/slab.h:748 [inline]
 ops_init+0xa9/0x220 net/core/net_namespace.c:127
 __register_pernet_operations net/core/net_namespace.c:1135 [inline]
 register_pernet_operations+0x1d4/0x420 net/core/net_namespace.c:1212
 register_pernet_subsys+0x24/0x40 net/core/net_namespace.c:1253
 nsim_fib_init+0x12/0x70 [netdevsim]
 veth_get_link_ksettings+0x2b/0x50 [veth]
 do_one_initcall+0xd4/0x454 init/main.c:939
 do_init_module+0xe0/0x330 kernel/module.c:3490
 load_module+0x3c2f/0x4620 kernel/module.c:3841
 __do_sys_finit_module+0x163/0x190 kernel/module.c:3931
 do_syscall_64+0x72/0x2e0 arch/x86/entry/common.c:296
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 3534:
 save_stack+0x19/0x80 mm/kasan/common.c:69
 set_track mm/kasan/common.c:77 [inline]
 __kasan_slab_free+0x130/0x180 mm/kasan/common.c:455
 slab_free_hook mm/slub.c:1423 [inline]
 slab_free_freelist_hook mm/slub.c:1474 [inline]
 slab_free mm/slub.c:3016 [inline]
 kfree+0xe9/0x2d0 mm/slub.c:3957
 ops_free net/core/net_namespace.c:151 [inline]
 ops_free_list.part.7+0x156/0x220 net/core/net_namespace.c:184
 ops_free_list net/core/net_namespace.c:182 [inline]
 __unregister_pernet_operations net/core/net_namespace.c:1165 [inline]
 unregister_pernet_operations+0x221/0x2a0 net/core/net_namespace.c:1224
 unregister_pernet_subsys+0x1d/0x30 net/core/net_namespace.c:1271
 nsim_fib_exit+0x11/0x20 [netdevsim]
 nsim_module_exit+0x16/0x21 [netdevsim]
 __do_sys_delete_module kernel/module.c:1015 [inline]
 __se_sys_delete_module kernel/module.c:958 [inline]
 __x64_sys_delete_module+0x244/0x330 kernel/module.c:958
 do_syscall_64+0x72/0x2e0 arch/x86/entry/common.c:296
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: 59c84b9f ("netdevsim: Restore per-network namespace accounting for fib entries")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pSeries machines on POWER9 processors can run with the XICS (legacy)
interrupt mode or with the XIVE exploitation interrupt mode. These
interrupt contollers have different interfaces for interrupt
management : XICS uses hcalls and XIVE loads and stores on a page.
H_EOI being a XICS interface the enable_scrq_irq() routine can fail
when the machine runs in XIVE mode.

Fix that by calling the EOI handler of the interrupt chip.

Fixes: f23e0643 ("ibmvnic: Clear pending interrupt after device reset")
Signed-off-by: NCédric Le Goater <clg@kaod.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__lpc_eth_shutdown is called after __lpc_eth_reset but it is already
calling __lpc_eth_reset. Avoid resetting the IP twice.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mariusz reported that invalid packets are sent after resume from
suspend if jumbo packets are active. It turned out that his BIOS
resets chip settings to non-jumbo on resume. Most chip settings are
re-initialized on resume from suspend by calling rtl_hw_start(),
so let's add configuring jumbo to this function.
There's nothing wrong with the commit marked as fixed, it's just
the first one where the patch applies cleanly.

Fixes: 7366016d ("r8169: read common register for PCI commit")
Reported-by: NMariusz Bialonczyk <manio@skyboo.net>
Tested-by: NMariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

reqsk_queue_empty() is called from inet_csk_listen_poll() while
other cpus might write ->rskq_accept_head value.

Use {READ|WRITE}_ONCE() to avoid compiler tricks
and potential KCSAN splats.

Fixes: fff1f300 ("tcp: add a spinlock to protect struct request_sock_queue")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

As mentioned in https://github.com/google/ktsan/wiki/READ_ONCE-and-WRITE_ONCE#it-may-improve-performance
a C compiler can legally transform

if (e->queue_index != queue_index)
	e->queue_index = queue_index;

to :

	e->queue_index = queue_index;

Note that the code using jiffies has no issue, since jiffies
has volatile attribute.

if (e->updated != jiffies)
    e->updated = jiffies;

Fixes: 83b1bc12 ("tun: align write-heavy flow entry members to a cache line")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Zhang Yu <zhangyu31@baidu.com>
Cc: Wang Li <wangli39@baidu.com>
Cc: Li RongQing <lirongqing@baidu.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support for Telit FN980 0x1050 composition

0x1050: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Without this patch, a command bit in the supported commands mask is only
ever set to unsupported during set online. If a command is ever marked as
unsupported (e.g. because of error during qeth_l2_vnicc_query_cmds),
subsequent successful initialization (offline/online) would not bring it
back.

Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>