Chipid of 88pm8607 is 0x40 or 0x50.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds a Pulse Width Modulation driver for Analog Baseband
Chip AB8500.
Signed-off-by: NArun Murthy <arun.murthy@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: NMattias Wallin <mattias.wallin@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch removes the requirement that gpio base be supplied in
platform data.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.

Tested with the SDHI hardware block included in sh7724.
Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Tested-by: NArnd Hannemann <arnd@arndnet.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On AP4EVB the card detect pin of the top SD/MMC slot is not directly
connected to the tmio/mmcif controller but to a GPIO pin, so polling
needs to be done for SDHI1 and MMCIF in order to support hotplug for
that slot. SHDI1 and MMCIF share that slot, and the used controller
is selected by a DIP switch.
This patch adds a helper function to check if a card is present in that
particular slot, registers this function with SDHI1 and MMCIF and enables
polling for SDHI1.
Signed-off-by: NArnd Hannemann <arnd@arndnet.de>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: NArnd Hannemann <arnd@arndnet.de>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sdhi hardware, so that polling needs to be used
with tmio_mmc and card detection is handled in the platform code.
This patch allows to set tmio_mmc capabilities (to pass the
MMC_CAP_NEEDS_POLL flag) and exposes a get_cd hook for that purpose.
Signed-off-by: NArnd Hannemann <arnd@arndnet.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: NArnd Hannemann <arnd@arndnet.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds support for the RTC provided by the Maxim 8998 chip. This
driver was tested on a GONI board by using the rtc-test application from
the Documentation/rtc.txt.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use genirq and provide seperated file for interrupts support.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.

Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

There is no reason to get irq twice.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch fixes da903x_add_subdevs error path:
1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add codec IRQ resources that are used in 88pm860x codec driver.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

For the resources allocated in tps6586x_i2c_probe(),
we need to free it in tps6586x_i2c_remove().
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

use the new definitions on twl header for code
consistency.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

use the new definitions on twl header for code
consistency.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

use the new definitions on twl header for code
consistency.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some modules already need to talk to at least PROTECT_KEY
register, while at that, add defines to the entire register
space.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

LP3974 PMIC support. It has same functionality as max8998.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NRabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This switches the AB3100 core driver to using MFD cells for
subdevices instead of spawning common platform devices.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since there is no discardable probe() function in the I2C device
framework, let's just tag it __devinit and take the footprint hit
rather than seeing the compilation warnings every day.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Not sure where this went.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fixed warnings about unprototyped global functions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  initramfs: Fix build break on symbol-prefixed archs
  initramfs: fix initramfs size calculation
  initramfs: generalize initramfs_data.xxx.S variants
  scripts/kallsyms: Enable error messages while hush up unnecessary warnings
  scripts/setlocalversion: update comment
  kbuild: Use a single clean rule for kernel and external modules
  kbuild: Do not run make clean in $(srctree)
  scripts/mod/modpost.c: fix commentary accordingly to last changes
  kbuild: Really don't clean bounds.h and asm-offsets.h

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: max8952 - fix max8952_set_voltage
  regulator: max8952 - fix max8952_pmic_probe error path
  regulator: fix build when CONFIG_REGULATOR_DUMMY=n
  regulator: avoid deadlock when disabling regulator with supply
  regulator: Add option for machine drivers to enable the dummy regulator
  Regulator: lp3972 cleanup
  Regulator: LP3972 PMIC regulator driver
  MAX8952 PMIC Driver Initial Release

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  nfs4: The difference of 2 pointers is ptrdiff_t
  nfs: testing the wrong variable
  nfs: handle lock context allocation failures in nfs_create_request
  Fixed Regression in NFS Direct I/O path

In current implementation, vid is declared as u8,
then "vid == -1" is always false, and "vid >= 0" is always true.
Thus change it to s8.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Commit f03f91826 (regulator: Add option for machine drivers
to enable the dummy regulator) in the regulators tree
seems to have introduced the following build break when
CONFIG_REGULATOR_DUMMY is disabled. Fix this.

  CC      drivers/regulator/dummy.o
drivers/regulator/dummy.c:41: error: redefinition of 'regulator_dummy_init'
drivers/regulator/dummy.h:28: note: previous definition of 'regulator_dummy_init' was here
make[2]: *** [drivers/regulator/dummy.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

I have a regulator A that sets regulator B as its supply. When I call
set_supply to add B as the supply for A, regulator A gets added to the
supply_list for regulator B.

When I call regulator_disable(A), I end up with a call chain like this:

regulator_disable(A)
> mutex_lock(A)
> _regulator_disable(A)
>> _regulator_disable(B)
>>> _notifier_call_chain(B)
>>>> mutex_lock(A)

Which results in dead lock since we are trying to acquire the mutex lock
for regulator A which we already hold.

This patch addresses this issue by moving the call to disable regulator
B outside of the lock aquired inside the initial call to
regulator_disable.

This change also addresses the issue of not acquiring the mutex for
regulator B before calling _regulator_disable(B).
Signed-off-by: NJeffrey Carlyle <jeff.carlyle@motorola.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.

It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch includes below fixes based on Mark's comment.
 - Return actual error if i2c_smbus_read_byte_data() fail
 - Add spaces around bitwise AND operator(&) to improve readability
 - Add comment to explain why we need to update voltage change control register
   for LDO1 and LDO5
 - Logging the value for diagnostics if chip reported incorrect voltage value
 - Add __devinit annotation for setup_regulators()
 - Show system control register1 value if the value is mismatched
 - Logging the value for diagnostics if failed to detect device
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.

If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.

We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
	- Style correction
	- Can accept platform_data with invalid GPIOs
	- Removed unnecessary features
	- Improved error handling
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>