Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 03 2月, 2021 9 次提交
  3. 02 2月, 2021 3 次提交
  5. 01 2月, 2021 1 次提交
  7. 31 1月, 2021 1 次提交
    • C
      neighbour: Prevent a dead entry from updating gc_list · eb4e8fac
      由 Chinmay Agarwal 提交于 
      Following race condition was detected:
<CPU A, t0> - neigh_flush_dev() is under execution and calls
neigh_mark_dead(n) marking the neighbour entry 'n' as dead.

<CPU B, t1> - Executing: __netif_receive_skb() ->
__netif_receive_skb_core() -> arp_rcv() -> arp_process().arp_process()
calls __neigh_lookup() which takes a reference on neighbour entry 'n'.

<CPU A, t2> - Moves further along neigh_flush_dev() and calls
neigh_cleanup_and_release(n), but since reference count increased in t2,
'n' couldn't be destroyed.

<CPU B, t3> - Moves further along, arp_process() and calls
neigh_update()-> __neigh_update() -> neigh_update_gc_list(), which adds
the neighbour entry back in gc_list(neigh_mark_dead(), removed it
earlier in t0 from gc_list)

<CPU B, t4> - arp_process() finally calls neigh_release(n), destroying
the neighbour entry.

This leads to 'n' still being part of gc_list, but the actual
neighbour structure has been freed.

The situation can be prevented from happening if we disallow a dead
entry to have any possibility of updating gc_list. This is what the
patch intends to achieve.

Fixes: 9c29a2f5 ("neighbor: Fix locking order for gc_list changes")
Signed-off-by: NChinmay Agarwal <chinagar@codeaurora.org>
Reviewed-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NDavid Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210127165453.GA20514@chinagar-linux.qualcomm.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      eb4e8fac
  9. 30 1月, 2021 17 次提交
    • D
      rxrpc: Fix deadlock around release of dst cached on udp tunnel · 5399d522
      由 David Howells 提交于 
      AF_RXRPC sockets use UDP ports in encap mode.  This causes socket and dst
from an incoming packet to get stolen and attached to the UDP socket from
whence it is leaked when that socket is closed.

When a network namespace is removed, the wait for dst records to be cleaned
up happens before the cleanup of the rxrpc and UDP socket, meaning that the
wait never finishes.

Fix this by moving the rxrpc (and, by dependence, the afs) private
per-network namespace registrations to the device group rather than subsys
group.  This allows cached rxrpc local endpoints to be cleared and their
UDP sockets closed before we try waiting for the dst records.

The symptom is that lines looking like the following:

	unregister_netdevice: waiting for lo to become free

get emitted at regular intervals after running something like the
referenced syzbot test.

Thanks to Vadim for tracking this down and work out the fix.

Reported-by: syzbot+df400f2f24a1677cd7e0@syzkaller.appspotmail.com
Reported-by: NVadim Fedorenko <vfedorenko@novek.ru>
Fixes: 5271953c ("rxrpc: Use the UDP encap_rcv hook")
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NVadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/161196443016.3868642.5577440140646403533.stgit@warthog.procyon.org.ukSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      5399d522
    • N
      net: bridge: add warning comments to avoid extending sysfs · 1e16f382
      由 Nikolay Aleksandrov 提交于 
      We're moving to netlink-only options, so add comments in the bridge's
sysfs files to warn against adding any new sysfs entries.
Signed-off-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      1e16f382
    • N
      net: bridge: mcast: drop hosts limit sysfs support · 7d0888d5
      由 Nikolay Aleksandrov 提交于 
      We decided to stop adding new sysfs bridge options and continue with
netlink only, so remove hosts limit sysfs support.
Signed-off-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      7d0888d5
    • V
      net: dsa: add a second tagger for Ocelot switches based on tag_8021q · 7c83a7c5
      由 Vladimir Oltean 提交于 
      There are use cases for which the existing tagger, based on the NPI
(Node Processor Interface) functionality, is insufficient.

Namely:
- Frames injected through the NPI port bypass the frame analyzer, so no
  source address learning is performed, no TSN stream classification,
  etc.
- Flow control is not functional over an NPI port (PAUSE frames are
  encapsulated in the same Extraction Frame Header as all other frames)
- There can be at most one NPI port configured for an Ocelot switch. But
  in NXP LS1028A and T1040 there are two Ethernet CPU ports. The non-NPI
  port is currently either disabled, or operated as a plain user port
  (albeit an internally-facing one). Having the ability to configure the
  two CPU ports symmetrically could pave the way for e.g. creating a LAG
  between them, to increase bandwidth seamlessly for the system.

So there is a desire to have an alternative to the NPI mode. This change
keeps the default tagger for the Seville and Felix switches as "ocelot",
but it can be changed via the following device attribute:

echo ocelot-8021q > /sys/class/<dsa-master>/dsa/tagging
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      7c83a7c5
    • V
      net: dsa: allow changing the tag protocol via the "tagging" device attribute · 53da0eba
      由 Vladimir Oltean 提交于 
      Currently DSA exposes the following sysfs:
$ cat /sys/class/net/eno2/dsa/tagging
ocelot

which is a read-only device attribute, introduced in the kernel as
commit 98cdb480 ("net: dsa: Expose tagging protocol to user-space"),
and used by libpcap since its commit 993db3800d7d ("Add support for DSA
link-layer types").

It would be nice if we could extend this device attribute by making it
writable:
$ echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging

This is useful with DSA switches that can make use of more than one
tagging protocol. It may be useful in dsa_loop in the future too, to
perform offline testing of various taggers, or for changing between dsa
and edsa on Marvell switches, if that is desirable.

In terms of implementation, drivers can support this feature by
implementing .change_tag_protocol, which should always leave the switch
in a consistent state: either with the new protocol if things went well,
or with the old one if something failed. Teardown of the old protocol,
if necessary, must be handled by the driver.

Some things remain as before:
- The .get_tag_protocol is currently only called at probe time, to load
  the initial tagging protocol driver. Nonetheless, new drivers should
  report the tagging protocol in current use now.
- The driver should manage by itself the initial setup of tagging
  protocol, no later than the .setup() method, as well as destroying
  resources used by the last tagger in use, no earlier than the
  .teardown() method.

For multi-switch DSA trees, error handling is a bit more complicated,
since e.g. the 5th out of 7 switches may fail to change the tag
protocol. When that happens, a revert to the original tag protocol is
attempted, but that may fail too, leaving the tree in an inconsistent
state despite each individual switch implementing .change_tag_protocol
transactionally. Since the intersection between drivers that implement
.change_tag_protocol and drivers that support D in DSA is currently the
empty set, the possibility for this error to happen is ignored for now.

Testing:

$ insmod mscc_felix.ko
[   79.549784] mscc_felix 0000:00:00.5: Adding to iommu group 14
[   79.565712] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
$ insmod tag_ocelot.ko
$ rmmod mscc_felix.ko
$ insmod mscc_felix.ko
[   97.261724] libphy: VSC9959 internal MDIO bus: probed
[   97.267363] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0
[   97.274998] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1
[   97.282561] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2
[   97.289700] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3
[   97.599163] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[   97.862034] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[   97.950731] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[   97.964278] 8021q: adding VLAN 0 to HW filter on device swp0
[   98.146161] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[   98.238649] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[   98.251845] 8021q: adding VLAN 0 to HW filter on device swp1
[   98.433916] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[   98.485542] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[   98.503584] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx
[   98.527948] device eno2 entered promiscuous mode
[   98.544755] DSA: tree 0 setup

$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=2.337 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.754 ms
^C
 -  10.0.0.1 ping statistics  -
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.754/1.545/2.337 ms

$ cat /sys/class/net/eno2/dsa/tagging
ocelot
$ cat ./test_ocelot_8021q.sh
        #!/bin/bash

        ip link set swp0 down
        ip link set swp1 down
        ip link set swp2 down
        ip link set swp3 down
        ip link set swp5 down
        ip link set eno2 down
        echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
        ip link set eno2 up
        ip link set swp0 up
        ip link set swp1 up
        ip link set swp2 up
        ip link set swp3 up
        ip link set swp5 up
$ ./test_ocelot_8021q.sh
./test_ocelot_8021q.sh: line 9: echo: write error: Protocol not available
$ rmmod tag_ocelot.ko
rmmod: can't unload module 'tag_ocelot': Resource temporarily unavailable
$ insmod tag_ocelot_8021q.ko
$ ./test_ocelot_8021q.sh
$ cat /sys/class/net/eno2/dsa/tagging
ocelot-8021q
$ rmmod tag_ocelot.ko
$ rmmod tag_ocelot_8021q.ko
rmmod: can't unload module 'tag_ocelot_8021q': Resource temporarily unavailable
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=0.953 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.787 ms
64 bytes from 10.0.0.1: seq=2 ttl=64 time=0.771 ms
$ rmmod mscc_felix.ko
[  645.544426] mscc_felix 0000:00:00.5: Link is Down
[  645.838608] DSA: tree 0 torn down
$ rmmod tag_ocelot_8021q.ko
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      53da0eba
    • V
      net: dsa: keep a copy of the tagging protocol in the DSA switch tree · 357f203b
      由 Vladimir Oltean 提交于 
      Cascading DSA switches can be done multiple ways. There is the brute
force approach / tag stacking, where one upstream switch, located
between leaf switches and the host Ethernet controller, will just
happily transport the DSA header of those leaf switches as payload.
For this kind of setups, DSA works without any special kind of treatment
compared to a single switch - they just aren't aware of each other.
Then there's the approach where the upstream switch understands the tags
it transports from its leaves below, as it doesn't push a tag of its own,
but it routes based on the source port & switch id information present
in that tag (as opposed to DMAC & VID) and it strips the tag when
egressing a front-facing port. Currently only Marvell implements the
latter, and Marvell DSA trees contain only Marvell switches.

So it is safe to say that DSA trees already have a single tag protocol
shared by all switches, and in fact this is what makes the switches able
to understand each other. This fact is also implied by the fact that
currently, the tagging protocol is reported as part of a sysfs installed
on the DSA master and not per port, so it must be the same for all the
ports connected to that DSA master regardless of the switch that they
belong to.

It's time to make this official and enforce it (yes, this also means we
won't have any "switch understands tag to some extent but is not able to
speak it" hardware oddities that we'll support in the future).

This is needed due to the imminent introduction of the dsa_switch_ops::
change_tag_protocol driver API. When that is introduced, we'll have
to notify switches of the tagging protocol that they're configured to
use. Currently the tag_ops structure pointer is held only for CPU ports.
But there are switches which don't have CPU ports and nonetheless still
need to be configured. These would be Marvell leaf switches whose
upstream port is just a DSA link. How do we inform these of their
tagging protocol setup/deletion?

One answer to the above would be: iterate through the DSA switch tree's
ports once, list the CPU ports, get their tag_ops, then iterate again
now that we have it, and notify everybody of that tag_ops. But what to
do if conflicts appear between one cpu_dp->tag_ops and another? There's
no escaping the fact that conflict resolution needs to be done, so we
can be upfront about it.

Ease our work and just keep the master copy of the tag_ops inside the
struct dsa_switch_tree. Reference counting is now moved to be per-tree
too, instead of per-CPU port.

There are many places in the data path that access master->dsa_ptr->tag_ops
and we would introduce unnecessary performance penalty going through yet
another indirection, so keep those right where they are.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      357f203b
    • V
      net: dsa: document the existing switch tree notifiers and add a new one · 886f8e26
      由 Vladimir Oltean 提交于 
      The existence of dsa_broadcast has generated some confusion in the past:
https://www.mail-archive.com/netdev@vger.kernel.org/msg365042.html

So let's document the existing dsa_port_notify and dsa_broadcast
functions and explain when each of them should be used.

Also, in fact, the in-between function has always been there but was
lacking a name, and is the main reason for this patch: dsa_tree_notify.
Refactor dsa_broadcast to use it.

This patch also moves dsa_broadcast (a top-level function) to dsa2.c,
where it really belonged in the first place, but had no companion so it
stood with dsa_port_notify.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      886f8e26
    • V
      net: dsa: tag_8021q: add helpers to deduce whether a VLAN ID is RX or TX VLAN · 9c7caf28
      由 Vladimir Oltean 提交于 
      The sja1105 implementation can be blind about this, but the felix driver
doesn't do exactly what it's being told, so it needs to know whether it
is a TX or an RX VLAN, so it can install the appropriate type of TCAM
rule.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      9c7caf28
    • E
      net: proc: speedup /proc/net/netstat · 0d6cd689
      由 Eric Dumazet 提交于 
      Use cache friendly helpers to better use cpu caches
while reading /proc/net/netstat

Tested on a platform with 256 threads (AMD Rome)

Before: 305 usec spent in netstat_seq_show()
After: 130 usec spent in netstat_seq_show()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210128162145.1703601-1-eric.dumazet@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      0d6cd689
    • K
      net: Remove redundant calls of sk_tx_queue_clear(). · df610cd9
      由 Kuniyuki Iwashima 提交于 
      The commit 41b14fb8 ("net: Do not clear the sock TX queue in
sk_set_socket()") removes sk_tx_queue_clear() from sk_set_socket() and adds
it instead in sk_alloc() and sk_clone_lock() to fix an issue introduced in
the commit e022f0b4 ("net: Introduce sk_tx_queue_mapping"). On the
other hand, the original commit had already put sk_tx_queue_clear() in
sk_prot_alloc(): the callee of sk_alloc() and sk_clone_lock(). Thus
sk_tx_queue_clear() is called twice in each path.

If we remove sk_tx_queue_clear() in sk_alloc() and sk_clone_lock(), it
currently works well because (i) sk_tx_queue_mapping is defined between
sk_dontcopy_begin and sk_dontcopy_end, and (ii) sock_copy() called after
sk_prot_alloc() in sk_clone_lock() does not overwrite sk_tx_queue_mapping.
However, if we move sk_tx_queue_mapping out of the no copy area, it
introduces a bug unintentionally.

Therefore, this patch adds a compile-time check to take care of the order
of sock_copy() and sk_tx_queue_clear() and removes sk_tx_queue_clear() from
sk_prot_alloc() so that it does the only allocation and its callers
initialize fields.

CC: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: NKuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: NTariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210128150217.6060-1-kuniyu@amazon.co.jpSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      df610cd9
    • X
      ip_gre: add csum offload support for gre header · efa1a65c
      由 Xin Long 提交于 
      This patch is to add csum offload support for gre header:

On the TX path in gre_build_header(), when CHECKSUM_PARTIAL's set
for inner proto, it will calculate the csum for outer proto, and
inner csum will be offloaded later. Otherwise, CHECKSUM_PARTIAL
and csum_start/offset will be set for outer proto, and the outer
csum will be offloaded later.

On the GSO path in gre_gso_segment(), when CHECKSUM_PARTIAL is
not set for inner proto and the hardware supports csum offload,
CHECKSUM_PARTIAL and csum_start/offset will be set for outer
proto, and outer csum will be offloaded later. Otherwise, it
will do csum for outer proto by calling gso_make_checksum().

Note that SCTP has to do the csum by itself for non GSO path in
sctp_packet_pack(), as gre_build_header() can't handle the csum
with CHECKSUM_PARTIAL set for SCTP CRC csum offload.

v1->v2:
  - remove the SCTP part, as GRE dev doesn't support SCTP CRC CSUM
    and it will always do checksum for SCTP in sctp_packet_pack()
    when it's not a GSO packet.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      efa1a65c
    • X
      net: support ip generic csum processing in skb_csum_hwoffload_help · 62fafcd6
      由 Xin Long 提交于 
      NETIF_F_IP|IPV6_CSUM feature flag indicates UDP and TCP csum offload
while NETIF_F_HW_CSUM feature flag indicates ip generic csum offload
for HW, which includes not only for TCP/UDP csum, but also for other
protocols' csum like GRE's.

However, in skb_csum_hwoffload_help() it only checks features against
NETIF_F_CSUM_MASK(NETIF_F_HW|IP|IPV6_CSUM). So if it's a non TCP/UDP
packet and the features doesn't support NETIF_F_HW_CSUM, but supports
NETIF_F_IP|IPV6_CSUM only, it would still return 0 and leave the HW
to do csum.

This patch is to support ip generic csum processing by checking
NETIF_F_HW_CSUM for all protocols, and check (NETIF_F_IP_CSUM |
NETIF_F_IPV6_CSUM) only for TCP and UDP.

Note that we're using skb->csum_offset to check if it's a TCP/UDP
proctol, this might be fragile. However, as Alex said, for now we
only have a few L4 protocols that are requesting Tx csum offload,
we'd better fix this until a new protocol comes with a same csum
offset.

v1->v2:
  - not extend skb->csum_not_inet, but use skb->csum_offset to tell
    if it's an UDP/TCP csum packet.
v2->v3:
  - add a note in the changelog, as Willem suggested.
Suggested-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      62fafcd6
    • E
      net: atm: pppoatm: use new API for wakeup tasklet · a5874597
      由 Emil Renner Berthing 提交于 
      This converts the driver to use the new tasklet API introduced in
commit 12cc923f ("tasklet: Introduce new initialization API")
Signed-off-by: NEmil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210127173256.13954-2-kernel@esmil.dkSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      a5874597
    • E
      net: atm: pppoatm: use tasklet_init to initialize wakeup tasklet · a5b88632
      由 Emil Renner Berthing 提交于 
      Previously a temporary tasklet structure was initialized on the stack
using DECLARE_TASKLET_OLD() and then copied over and modified. Nothing
else in the kernel seems to use this pattern, so let's just call
tasklet_init() like everyone else.
Signed-off-by: NEmil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210127173256.13954-1-kernel@esmil.dkSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      a5b88632
    • P
      net: flow_offload: Add original direction flag to ct_metadata · 941eff5a
      由 Paul Blakey 提交于 
      Give offloading drivers the direction of the offloaded ct flow,
this will be used for matches on direction (ct_state +/-rpl).
Signed-off-by: NPaul Blakey <paulb@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      941eff5a
    • P
      net/sched: cls_flower: Add match on the ct_state reply flag · 8c85d18c
      由 Paul Blakey 提交于 
      Add match on the ct_state reply flag.

Example:
$ tc filter add dev ens1f0_0 ingress prio 1 chain 1 proto ip flower \
  ct_state +trk+est+rpl \
  action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_1 ingress prio 1 chain 1 proto ip flower \
  ct_state +trk+est-rpl \
  action mirred egress redirect dev ens1f0_0
Signed-off-by: NPaul Blakey <paulb@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      8c85d18c
    • M
      net: packet: make pkt_sk() inline · 8c224751
      由 Menglong Dong 提交于 
      It's better make 'pkt_sk()' inline here, as non-inline function
shouldn't occur in headers. Besides, this function is simple
enough to be inline.
Signed-off-by: NMenglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/20210127123302.29842-1-dong.menglong@zte.com.cnSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      8c224751
  11. 29 1月, 2021 9 次提交