Nothing appears to use BOOT_LOAD so remove it as a configurable option.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds the missing MODULE_LICENSE("GPL").
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fedora 9 works on Efika without the separate 'device-tree supplement',
thanks to the kernel's own fixups. With one exception -- because 'CHRP'
still appears on the 'machine:' line in /proc/cpuinfo, the installer
misdetects the platform and misconfigures yaboot, putting it into a PReP
boot partition instead of in the /boot filesystem where the Efika's
firmware could find it.

The kernel's fixups for Efika already correct one instance of 'chrp', in
the 'device_type' property. This fixes it in the 'CODEGEN,description'
property too, since that's what's exposed to userspace in /proc/cpuinfo.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This implements support for the GPIO LIB API.  Two calls are still
unimplemented though: irq_to_gpio and gpio_to_irq.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the handling of the preempt count when switching
interrupt stacks so that HW interrupt properly get the softirq
mask copied over from the previous stack.

It also initializes the softirq stack preempt_count to 0 instead
of SOFTIRQ_OFFSET, like x86, as __do_softirq() does the increment,
and we hit some lockdep checks if we have it twice.

That means we do run for a little while off the softirq stack
with the preempt-count set to 0, which could be deadly if we
try to take a softirq at that point, however we do so with
interrupts disabled, so I think we are ok.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently, we initialize the "current" pointer in the PACA (which
is used by the "current" macro in the kernel) before calling
setup_system(). That means that early_setup() is called with
current still "NULL" which is -not- a good idea. It happens to
work so far but breaks with lockdep when early code calls printk.

This changes it so that all PACAs are statically initialized with
__current pointing to the init task. For non-0 CPUs, this is fixed
up before use.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This changes the cpu_idle loop for 44x platforms to utilize the Wait Enable
feature of the CPU.  This helps virtulization solutions know when the guest
Linux kernel is in an idle state.

A command line option called "idle" is also added to allow people to change
the idle loop back to the original variation.  This is done by setting
"idle=spin" on the kernel command line.
Signed-off-by: NJerone Young <jyoung5@us.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add a multi-board PowerPC 40x defconfig file
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Board specific defconfigs are useful, however with the ability to do
multi-board defconfigs they aren't needed in the top level configs directory.

Move the 4xx board specific defconfigs to individual directories under
arch/powerpc/configs.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now that we have the alpaca, the reg_save_ptr is no longer needed in the
paca.  Eradicate all global uses of it and make it static in the iSeries
lpardata.c
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The iSeries HV only needs the first two fields of the paca statically
initialised, so create an alternate paca that contains only those and
switch to our real paca immediately after boot.

This is in order to make the 1024 cpu patches easier since they will no
longer have to statically initialise the pacas for iSeries.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file.  Rename the requested boot image file to
dtbImage.prpmc2800.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform.  Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank.  This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports.  The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device.  The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove several unused (or software config only) properties.
Rename marvel node to "system-controller".  Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Compatible names should refer to a specific version of the hardware,
without wildcards.  Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated.  This fixes them.  Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The allyesconfig (among others) build was giving this:

In file included from include/linux/gfp.h:4,
                 from include/linux/slab.h:14,
                 from include/linux/percpu.h:5,
                 from include2/asm/time.h:18,
                 from include2/asm/cputime.h:26,
                 from include/linux/sched.h:67,
                 from
arch/powerpc/kernel/asm-offsets.c:17:
include/linux/mmzone.h:791:2: error: #error Allocator MAX_ORDER exceeds SECTION_SIZE

Kconfig options are order depenendent, so move the setting of
FORCE_MAX_ZONEORDER to after the setting of PPC_64K_PAGES. Also add an
explicit !PPC_64K_PAGES.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If an SLB miss interrupt happens while the RI bit of MSR is zero, we
can't just return, because RI being zero indicates that SRR0/SRR1
potentially had live values in them, and the process of taking an
interrupt overwrites them.

This should never happen, but if it does, we try to print a nice oops
message.  That doesn't work, however, because the code at unrecov_slb
assumes that the MMU has been turned on, but we call it with the MMU
off (and have done so since the SLB miss handler was rewritten to run
without turning the MMU on) -- except on iSeries, where everything runs
with the MMU on.

This fixes it by adding the necessary code to turn the MMU on if
necessary.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We really need to ack interrupts at mpic_teardown, since
not all platforms reset mpic at kernel start-up. For example,
kexec'ed kernel hangs on P.A. Semi if mpic_eoi() isn't called.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Clean up the pwrficient iommu code a bit. It was using u32 *-based offsets
for registers, which can be a bit confusing when comparing to the manual.

Generated binaries from the code is unchanged from before.
Signed-off-by: NOlof Johansson <olof@lixom.net>

This will remove some build warnings and doesn't stop us building any
drivers that we were building previously with these configs.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This eliminates a warning in builds that don't define
CONFIG_MEMORY_HOTPLUG.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A couple of places are duplicating the function of
of_device_is_available; convert them to use it.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This enables the FORCE_MAX_ZONEORDER Kconfig option for all PowerPC
systems.  Previously, it was enabled only for 64-bit systems.  We also
make the option selectable from the menu, so that the user can specify
different values.  This is useful for 32-bit systems that need to
allocate more than 4MB of physically contiguous memory.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We have an assembly version of strncmp for the bootwrapper, but not
for the kernel, so we end up using the C version in the kernel.  This
takes the strncmp code from the bootup and copies it to the kernel
proper, adding two instructions so it copes correctly with len==0.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Replace logical "&&" by bit "&" for ISA_SPACE_MASK.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Include the newly added Canyonlands and Yosemite ports in the mutli-board
440 defconfig.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

With a multiplatform kernel, once built we always have warp_setup_nand_flash()
called and NDFC probed, no matter what machine we actually run on. This
potentially can cause problems (such as kernel crash), since NDFC is probed at
a warp-predefined address.

Using machine_device_initcall() NAND devices are registered if we run on a warp only.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:

- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
  (the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This gets the FEC ethernet driver working again on the lite5200
platform.

The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200.  Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B.  This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: NRené Bürgel <r.buergel@unicontrol.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

DTS updates that fix booting problems on mpc5200-based boards:
- change to ethernet reg property
- addition of mdio and phy nodes
- removal of pci node (Motion-Pro board)

Other DTS updates:
- update i2c device tree nodes
- add lpb bus node and flash device (without partitions defined)
- add rtc i2c nodes
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Handling of the proc_dir_entry->count was changed in 2.6.24-rc5.
After this change, the default value for pde->count is 1 and not 0 as
before.  Therefore, if we want to check whether our procfs file is
already opened (already in use), we have to check if pde->count is
greater than 2 rather than 1.
Signed-off-by: NMaxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: NJens Osterkamp <jens@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

hash_page_sync() takes and releases the low level mmu hash
lock in order to sync with other processors disposing of page
tables.  Because that lock can be needed to service hash misses
triggered by interrupt handlers, taking it must be done with
interrupts off.  However, hash_page_sync() appears to be called
with interrupts enabled, thus causing occasional deadlocks.

We fix it by making sure hash_page_sync() masks interrupts while
holding the lock.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A subtle bug sneaked into iSeries recently.  On this platform, we must
not normally clear MSR:EE (the hardware external interrupt enable)
except for short periods of time.  Taking an interrupt while
soft-disabled doesn't cause us to clear it for example.

The iSeries kernel expects to mostly run with MSR:EE enabled at all
times except in a few exception entry/exit code paths.  Thus
local_irq_enable() doesn't check if it needs to hard-enable as it
expects this to be unnecessary on iSeries.

However, hard_irq_disable() _does_ cause MSR:EE to be cleared,
including on iSeries.  A call to it was recently added to the
context switch code, thus causing interrupts to become disabled
for a long periods of time, causing the iSeries watchdog to kick
in under some circumstances and other nasty things.

This patch fixes it by making local_irq_enable() properly re-enable
MSR:EE on iSeries.  It basically removes a return statement here
to make iSeries use the same code path as everybody else.  That does
mean that we might occasionally get spurious decrementer interrupts
but I don't think that matters.

Another option would have been to make hard_irq_disable() a nop
on iSeries but I didn't like it much, in case we have good reasons
to hard-disable.

Part of the patch is fixes to make sure the hard_enabled PACA field
is properly set on iSeries as it used not to be before, since it
was mostly unused.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A missing break statement in a switch caused cpm2_clk_setup() to initialize
SCC2 instead of SCC1.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>