After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.

This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For sdio chip, the max credit size in firmware is 1556, the 1556
include payload, ieee80211 header, htt header, htc header. So it
need to set the max mtu to 1500 to forbidden TX packet which exceed
1500 form application.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On SDIO chips the firmware log does not impact performance. To make it
easier to debug firmware problems keep it enabled on the firmware.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make sure the number of WBM_IDLE_LINK ring descriptors is power
of 2. This increases the number of descriptors to 32k from the
current ~18k to fix the target assert because of the shortage in
the descriptors in WBM_IDLE_LINK ring. Remove unnecessary
power of 2 calculation in ath11k_dp_link_desc_setup() as it is
not required after this change.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TLV length was 0 for TLV tag 'WMI_TAG_ARRAY_STRUCT' causing
Q6 to crash when trying to configure pktlog filter via debugfs.
Signed-off-by: NVikas Patel <vikpatel@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

skb_panic is hit during msdu coalescing whenever
enough tailroom is not allocated based on the remaining
msdu length which is spread across in different rx buffers.

Compute the extra length for resizing the skb based on
the total msdu length and the msdu length of the first buffer.
Signed-off-by: NSriram R <srirrama@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

remove unused counter to avoid taking locks inorder to optimize
cpu load.

Using Flamegraph, cpu usage of ath11k_dp_tx() observed to be decreased
from 5.58% to 3.74% with iperf traffic running with 80MHz bandwidth ap
mode.
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In conf_tx() mac operation callback, we are truncating the tx
params cw_min and cw_max due to lower data type cast. so modified
the data type of cwmin and cwmax to avoid the trucation issue.
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch drops ath11k_hal_rx_parse_dst_ring_desc(). This function was
creating a huge amount of load, which lead to a signifcant latency delay
when processing data in the RX path.

Pegging the processing on a specific core and running perf --top we get
the following output when running HE80 at a fixed bandwidth of 1gbit.

with patch
    19.19%  [ath11k]       [k] ath11k_dp_process_rx
     5.02%  [ath11k]       [k] ath11k_dp_rx_tid_del_func
     4.39%  [kernel]       [k] v7_dma_inv_range
     4.15%  [kernel]       [k] __slab_alloc.constprop.1
     4.03%  [kernel]       [k] dev_gro_receive
     3.86%  [kernel]       [k] tcp_gro_receive
     3.07%  [ip_tables]    [k] ipt_do_table
     2.96%  [kernel]       [k] dma_cache_maint_page

without patch
    21.64%  [ath11k]       [k] ath11k_hal_rx_parse_dst_ring_desc
    10.80%  [ath11k]       [k] ath11k_dp_process_rx
     3.77%  [kernel]       [k] v7_dma_inv_range
     3.48%  [kernel]       [k] dev_gro_receive
     3.32%  [ath11k]       [k] ath11k_dp_rx_tid_del_func
     3.17%  [mac80211]     [k] ieee80211_rx_napi
     2.70%  [kernel]       [k] dma_cache_maint_page
     2.65%  [mac80211]     [k] ieee80211_sta_ps_transition

When removing the the bandwidth limit and rerunning the test we see an
overall throughput improvement of 3-400mbit when running 4x4 HE80.
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It is observed that ath11k STA mode UL throughput is low.
This is due to packets delivered to FW from TCL instead of TQM.
TCL AST search fail causes packet delivered to FW, fix this by
properly configuring the TCL address search type and ast_hash.
STA UL throughput is improved 10times with 11AC AP.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The current ath11k driver failed to parse
wmi_tlv_svc_rdy_ext_parse if there is change in
wmi_mac_phy_capabilities length with below error.

ath11k c000000.wifi1: failed to extract mac caps, idx :0
ath11k c000000.wifi1: failed to parse tlv -22

This is needed to get firmware version
WLAN.HK.2.0.0.1-00240-QCAHKSWPL_SILICONZ-1 working.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Handled the error case with proper resource cleanup and
moved the handling into a separate function from
ath11k_mac_sta_state.
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The Previous configuartion of htt stats sounding info and pdev cca stats
are invalid due to that getting time out error.

Changing htt stats sounding info value from 0xFF to 0x00 and htt pdev cca
stats from 0x10 to 0x00
Signed-off-by: NGanesh Sesetti <gseset@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

During driver load below warn logs are printed in the console if
firmware doesn't support some optional HTC services, ex:pktlog.
It is likely some older fw version may not support PKTLOG HTC
service as legacy fw uses HTC DATA service  for pktlog.
Move this log to debug level to remove un-necessary warn message
on console.

htc.c:803:  ath10k_warn(ar, "unsupported HTC service id: %d\n",
htc.c:881:  ath10k_warn(ar, "unsupported HTC service id: %d\n",
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Trigger the WMI call en/disabling OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add target wait time wmi calls to the driver. En/disable the support
from when the bss_config changes. We ignore the cmd completion events.
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add basic HE support to the driver. The sband_iftype data is generated from
the capabilities read from the FW.
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remove unexecuted code while handling amsdu packets.
The same logic is done before calling ath11k_dp_rx_msdu_coalesce
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX rate stats for the retried packets for a station comes through
tx completion events. Assigning hw reported bandwidth information
directly to station's txrate bandwidth will cause below warning.
Fix this warning by converting the hw reported bandwidth to
mac80211 base bandwidth.

[ 134.758190] PC is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.765730] LR is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.875014] [<ffffffbffca8d708>] cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.877192] [<ffffffbffcaa9704>] nl80211_put_sta_rate+0x54/0xf24 [cfg80211]
[ 134.884829] [<ffffffbffcaa9d48>] nl80211_put_sta_rate+0x698/0xf24 [cfg80211]
[ 134.891687] [<ffffffbffcaaa490>] nl80211_put_sta_rate+0xde0/0xf24 [cfg80211]
[ 134.898975] [<ffffffc0004de748>] genl_lock_dumpit+0x30/0x4c
[ 134.905998] [<ffffffc0004dc264>] netlink_dump+0xf4/0x248
[ 134.911291] [<ffffffc0004dc910>] __netlink_dump_start+0xe0/0x174
[ 134.916850] [<ffffffc0004df114>] genl_family_rcv_msg+0x130/0x2c0
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We can regularly see the following message.
- "ath11k c000000.wifi1: failed to find the peer with peer_id 4"
This happens when the FW starts sending stats for the peer whilst the
peer is not fully associated. Convert this info message to a debug one.
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Everytime a new peer gets associated, we see the following message in the log
- ath11k c000000.wifi1: Unknown eventid: 0x6017
Ignore this event for now. We probably need to handle the event properly when
we add OMI support.
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

mac80211 expects the definition of what HE rate info is available inside a
struct prepended to the skb.
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add an entry for ath11k to the MAINTAINERS file.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.

Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.

Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.

Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.

The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:

https://github.com/kvalo/ath11k-firmware

This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.

The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NBhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: NGanesh Sesetti <gseset@codeaurora.org>
Signed-off-by: NGovindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NManikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: NMiles Hu <milehu@codeaurora.org>
Signed-off-by: NMuna Sinada <msinada@codeaurora.org>
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NSathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: NShashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: NSriram R <srirrama@codeaurora.org>
Signed-off-by: NSven Eckelmann <seckelmann@datto.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NVenkateswara Naralasetty <vnaralas@codeaurora.org>

ath11k is a driver for Qualcomm IEEE 802.11ax devices. Add a
bindings document for the driver, first documenting IPQ8074 which is the
only device ath11k currently supports.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There is a check on the retry counter invalid_buf_id_retry that is always
false because invalid_buf_id_retry is initialized to zero on each iteration
of a while-loop.  Fix this by initializing the retry counter before the
while-loop starts.

Addresses-Coverity: ("Logically dead code")
Fixes: b4a967b7 ("wil6210: reset buff id in status message after completion")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.

By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.

Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011

Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NLinus Lüssing <ll@simonwunderlich.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

iw command only show rssi without each chain's rssi on sdio
iw wlan0 station dump
Station a0:40:a0:93:3e:de (on wlan0)
signal:         -82 dBm
signal avg:     -82 dBm

after this patch, it will show each chain's rssi on sdio
Station a0:40:a0:93:3e:de (on wlan0)
signal:         -82 [-84, -88] dBm
signal avg:     -82 [-84, -87] dBm

For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it
indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the
rssi of each chain stored in rx management reported by firmware, the
ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the
rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate
them to mac80211. For non-tlv wmi chip, it will not get the rssi of each
chain and not indicate to mac80211, for non-tlv wmi chip, this patch will
not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid,
it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi
of 2 chain in mgmt is valid.

rssi of chains in mgmt of QCA6174 SDIO:
92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70
92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68
92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128
92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128

rssi of chains in mgmt of QCA6174 PCIe:
[ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17
[ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22
[ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128
[ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128

after apply this patch, the iw's rssi of PCIe do not changed, result is
same with before.

iw wlan0 station dump of QCA6174 PCIe:
Station 6c:e8:73:b8:92:dc (on wlan0)
        signal:         -70 [-77, -72] dBm
        signal avg:     -69 [-78, -72] dBm

iw wlan-5000mhz station dump of QCA9984 PCIe
connected with 2 client which has 2 chain:
Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz)
        signal:         -47 [-55, -48, -87, -88] dBm
        signal avg:     -42 [-50, -43, -83, -86] dBm
Station ac:c1:ee:39:e3:83 (on wlan-5000mhz)
        signal:         -43 [-46, -45, -79, -84] dBm
        signal avg:     -43 [-46, -46, -82, -83] dBm

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the BDF download QMI message has the end field set to 1, it signals
the end of the transfer, and triggers the firmware to do a CRC check.  The
BDFs for msm8998 devices fail this check, yet the firmware is happy to
still use the BDF.  It appears that this error is not caught by the
downstream drive by concidence, therefore there are production devices
in the field where this issue needs to be handled otherwise we cannot
support wifi on them.  So, attempt to detect this scenario as best we can
and treat it as non-fatal.
Signed-off-by: NJeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When ath10k_qmi_init() fails, the error handling does not free the irq
resources, which causes an issue if we EPROBE_DEFER as we'll attempt to
(re-)register irqs which are already registered.

Fix this by doing a power off since we just powered on the hardware, and
freeing the irqs as error handling.

Fixes: ba94c753 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: NJeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add NL80211_FEATURE_ND_RANDOM_MAC_ADDR for NLO will enable the random
mac address for netdetect case.
iw command:
iw phy0 wowlan enable net-detect net-detect
randomize=AA:7B:A1:AC:B2:41/FF:FF:FF:FF:FF:FF interval 5000 delay 30
freqs 2412 matches ssid foo.
After suspend, DUT will send probe request with mac AA:7B:A1:AC:B2:41.

WCN3990, QCA9377, QCA6174 PCI also support this feature.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Firmware with the build id QC_IMAGE_VERSION_STRING=WLAN.HL.1.0.2-XXXX does
not support the QMI_WLFW_HOST_CAP_REQ_V01 message and will return the
QMI not supported error to the ath10k driver.  Since not supporting this
message is not fatal to the firmware nor the ath10k driver, lets catch
this particular scenario and ignore it so that we can still bring up
wifi services successfully.
Signed-off-by: NJeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Download firmware time cost of SDIO is too long, it is about 480ms,
add large size 2048 bytes for BMI download for SDIO chip, its time
cost will reduced to 240ms.

This will optimize the download firmware time cost.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.

Fixes: ce834e28 ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It seems to be unused.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Do some cosmetic cleanup while reviewing the files. No functional changes.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.

This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.

Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.

The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.

The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.

Test result of different length of data:
data packet(byte)   cost time(us)   calculated rate(Mbps)
      256               28                73
      512               33               124
     1024               35               234
     1792               45               318
    14336              168               682
    28672              333               688
    57344              660               695

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: NAlagu Sankar <alagusankar@silex-india.com>
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NEduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>