The NEQ interrupt is only triggered when there was no previous pending
interrupt. If we request irq handling after an interrupt has occurred,
we will never get an interrupt until we call H_RESET_EVENTS.

Events seem to be cleared when we first register the NEQ. So, when we
requested irq handling right after registering it, a possible race with
an interrupt was much less likely. Now, there is a chance we may lose
this race and never get any events.

The fix here is to poll and acknowledge any events that might have
happened right after registering the irq handler.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the caller (PM resume code) is not the one holding rtnl, when taking the
'else' branch rtnl may be released at any moment, thereby defeating the whole
purpose of this code block.
Signed-off-by: NBenjamin Poirier <bpoirier@suse.de>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The r8169 may get stuck or show bad behaviour after activating TSO :
the net_device is not stopped when it has no more TX descriptors.
This problem comes from TX_BUFS_AVAIL which may reach -1 when all
transmit descriptors are in use. The patch simply tries to keep positive
values.

Tested with 8111d(onboard) on a D510MO, and with 8111e(onboard) on a
Zotac 890GXITX.
Signed-off-by: NJulien Ducourthial <jducourt@free.fr>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If RSS is disabled on the PF (efx->n_rx_channels == 1) we try to set
up the indirection table so that VFs can use it, setting
efx->rss_spread = efx_vf_size(efx).  But if SR-IOV was disabled at
compile time, this evaluates to 0 and we end up dividing by zero when
initialising the table.

I considered changing the fallback definition of efx_vf_size() to
return 1, but its value is really meaningless if we are not going to
enable VFs.  Therefore add a condition of efx_sriov_wanted(efx) in
efx_probe_interrupts().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Some RNDIS devices include a bogus CDC Union descriptor pointing
to non-existing interfaces.  The RNDIS code is already prepared
to handle devices without a CDC Union descriptor by hardwiring
the driver to use interfaces 0 and 1, which is correct for the
devices with the bogus descriptor as well. So we can reuse the
existing workaround.

Cc: Markus Kolb <linux-201011@tower-net.de>
Cc: Iker Salmón San Millán <shaola@esdebian.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: 655387@bugs.debian.org
Cc: stable@vger.kernel.org
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a bug fix for an "interface fails to load" issue.
The issue occurs when bnx2x driver loads after UNDI driver was previously
loaded over the chip. In such a scenario the UNDI driver is loaded and operates
in the pre-boot kernel, within its own specific host memory address range.
When the pre-boot stage is complete, the real kernel is loaded, in a new and
distinct host memory address range. The transition from pre-boot stage to boot
is asynchronous from UNDI point of view.

A race condition occurs when UNDI driver triggers a DMAE transaction to valid
host addresses in the pre-boot stage, when control is diverted to the real
kernel. This results in access to illegal addresses by our HW as the addresses
which were valid in the preboot stage are no longer considered valid.
Specifically, the 'was_error' bit in the pci glue of our device is set. This
causes all following pci transactions from chip to host to timeout (in
accordance to the pci spec).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Silence sparse warnings shown below:
...
drivers/net/ethernet/intel/e1000/e1000_main.c:3435:17: warning:
	cast to restricted __le64
drivers/net/ethernet/intel/e1000/e1000_main.c:3435:17: warning:
	cast to restricted __le64
...
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.

So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NJohn Bishop <johnx.bishop@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.

This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.

As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.

Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After this commit:

commit aacc1bea
Author: Multanen, Eric W <eric.w.multanen@intel.com>
Date:   Wed Mar 28 07:49:09 2012 +0000

    ixgbe: driver fix for link flap

The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.

We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It was possible for shutdown to pull the rug out from other driver entry
points.  Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Cc: Hariharan Nagarajan <hanagara@cisco.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up.  Fixed by casting
gp->wake_on_lan to bool.  Tested on an iBook G4.
Signed-off-by: NGerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a844adfd.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.

spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.

So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.

Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: NKai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.

Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.

Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver calls cxgb_vlan_mode() from init_one().  This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets().  So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.

This was found because of the lockdep warning:

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
    Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
    Call Trace:
     [<ffffffff8106e767>] register_lock_class+0x108/0x2d0
     [<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
     [<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
     [<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
     [<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
     [<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
     [<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
     [<ffffffff81042206>] do_work_for_cpu+0x10/0x22
     [<ffffffff810482de>] kthread+0xa1/0xa9
     [<ffffffff8138e234>] kernel_thread_helper+0x4/0x10

Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was freeing memory in shutdown instead of remove.  As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver.  This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: NSamuel Liao <samuelliao@tencent.com>
Signed-off-by: NShan Wei <davidshan@tencent.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.

Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also explicitly set the phy to advertise 1000 speeds
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d9460920Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O.  Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.

Fix this by freeing glue data last.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 2a190322 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.

BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When our driver device is removed on the AHB bus, our IO memory is never unmapped.
Signed-off-by: NJonathan Bither <jonbither@gmail.com>
Reviewed-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dpc takes care of all data packets transmissions for sdio function
2. It is possible that it misses some completion events when the
traffic is heavy or it's running on a slow cpu. A linked list is
introduced to make sure dpc is invoked whenever needed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO stack doesn't have a structure for function 0. The structure
pointer stored in card->sdio_func[0] is actually for function 1.
With current implementation the register read/write is applied to
function 1. This pathch fixes the issue.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link

Tested on my Beagle XM.

v2: added mantainer to the list of recipient
Signed-off-by: NPaolo Pisati <paolo.pisati@canonical.com>
Acked-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
  but have no place in the kernel proper.

This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.

We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.

Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.

Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: NStephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>