As we now never read back our current head position from the CSB
pointers register, and the HW itself doesn't use it to prevent
overwriting unread CSB entries, we do not need to keep updating the
register. As it turns out this register is not listed as being shadowed,
and so requires forcewake -- but we haven't been taking forcewake around
it so the writes has probably been regularly dropped. Fortuitously, we
only read the value after a reset where it did not matter, and zero was
the right answer (well, close enough).

Mika pointed out that this was how we used to do it (accidentally!)
before he fixed it in commit cc53699b ("drm/i915: Use masked write
for Context Status Buffer Pointer").

References: cc53699b ("drm/i915: Use masked write for Context Status Buffer Pointer")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-7-chris@chris-wilson.co.uk

On HW reset, the HW clears the write pointer (to 0). But since it also
writes its first CSB entry to slot 0, we need to reset the write pointer
back to the element before (so the first entry we read is 0).

This is required for the next patch, where we trust the CSB completely!

v2: Use _MASKED_FIELD
v3: Store the reset value, so that we differentiate between mmio/hwsp
transparently and without pretense.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-6-chris@chris-wilson.co.uk

Following the removal of the last workarounds, the only CSB mmio access
is for the old vGPU interface. The mmio registers presented by vGPU do
not require forcewake and can be treated as ordinary volatile memory,
i.e. they behave just like the HWSP access just at a different location.
We can reduce the CSB access to a set of read/write/buffer pointers and
treat the various paths identically and not worry about forcewake.
(Forcewake is nightmare for worstcase latency, and we want to process
this all with irqsoff -- no latency allowed!)

v2: Comments, comments, comments. Well, 2 bonus comments.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-5-chris@chris-wilson.co.uk

In the next patch, we will process the CSB events directly from the
submission path, rather than only after a CS interrupt. Hence, we will
no longer have the need for a loop until the has-interrupt bit is clear,
and in the meantime can remove that small optimisation.

v2: Tvrtko pointed out it was safer to unconditionally kick the tasklet
after each irq, when assuming that the tasklet is called for each irq.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-4-chris@chris-wilson.co.uk

In the following patch, we will process the CSB events under the
timeline.lock and not serialised by the tasklet. This also means that we
will need to protect access to common variables such as
execlists->csb_head with the timeline.lock during reset.

v2: Move sync_irq to avoid deadlocks between taking timeline.lock from
our interrupt handler.
v3: Kill off the synchronize_hardirq as it raises more questions than
answered; now we use the timeline.lock entirely for CSB serialisation
between the irq and elsewhere, we don't need to be so heavy handed with
flushing
v4: Treat request cancellation (wedging after failed reset) similarly
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-3-chris@chris-wilson.co.uk

In the next patch, we will begin processing the CSB from inside the
submission path (underneath an irqsoff section, and even from inside
interrupt handlers). This means that updating the execlists->port[] will
no longer be serialised by the tasklet but needs to be locked by the
engine->timeline.lock instead. Pull dequeue and submit under the same
lock for protection. (An alternate future plan is to keep the in/out
arrays separate for concurrent processing and reduced lock coverage.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-2-chris@chris-wilson.co.uk

We do not need to do a posting read of our uncached mmio write to
re-enable the master interrupt lines after handling an interrupt, so
don't. This saves us a slow UC read before we can process the interrupt,
most noticeable in execlists where any stalls imposes extra latency on
GPU command execution.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628201211.13837-1-chris@chris-wilson.co.uk

We're fetching GuC/HuC firmwares directly from uc level during
init_early stage but this breaks guc/huc struct isolation and
also strict SW-only initialization rule for init_early. Move fw
fetching to init phase and do it separately per guc/huc struct.

v2: don't forget to move wopcm_init - Michele
v3: fetch in init_misc phase - Michal
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #2
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628141522.62788-2-michal.wajdeczko@intel.com

We will add more init steps to misc phase and there is no need
to expose them separately for use in uc_init_misc function.
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628141522.62788-1-michal.wajdeczko@intel.com

Avoid calling dma_fence_signal() from inside the interrupt if we haven't
enabled signaling on the request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-4-chris@chris-wilson.co.uk

Rather than have multiple locked instructions inside the notify_ring()
irq handler, move them inside the spinlock and reduce their intrinsic
locking.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-3-chris@chris-wilson.co.uk

If we have more interrupts pending (because we know there are more
breadcrumb signals before the completion), then we do not need to
trigger an irq_seqno_barrier or even wakeup the task on this interrupt
as there will be another. To allow some margin of error (we are trying
to work around incoherent seqno after all), we wakeup the breadcrumb
before the target as well as on the target.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-2-chris@chris-wilson.co.uk

By taking advantage of the RCU protection of the task struct, we can find
the appropriate signaler under the spinlock and then release the spinlock
before waking the task and signaling the fence.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627201304.15817-1-chris@chris-wilson.co.uk

At the moment, gem_exec_gttfill fails with a sporadic EBUSY due to us
wanting to unbind a pinned batch. Let's dump who first bound that vma to
see if that helps us identify who still unexpectedly has it pinned.

v2: We cannot allocate inside the printer (as it may be on an fs-reclaim
path), so hope for the best and build the string on the stack
v3: stack depth of 16 routinely overflows a 512 character string, limit
it to 12 to avoid unsightly truncation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628132206.8329-1-chris@chris-wilson.co.uk

This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-6-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-5-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-4-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-3-tdz@users.sourceforge.net

This patch unifies the naming of DRM functions for reference counting
of struct drm_connector. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: NThomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618110154.30462-2-tdz@users.sourceforge.net

This patch addresses Interrupts from south display engine (SDE).

ICP has two registers - SHOTPLUG_CTL_DDI and SHOTPLUG_CTL_TC.
Introduce these registers and their intended values.

Introduce icp_irq_handler().

The icp_irq_postinstall() takes care of
enabling all PCH interrupt sources, to unmask
them as needed with SDEIMR, as is done
done by ibx_irq_pre_postinstall() for earlier platforms.
We do not need to explicitly call the ibx_irq_pre_postinstall().

Also, while changing these,
s/CPT/PPT/CPT-CNP comment.

v2:
- remove redundant register defines.(Lucas)
- Change register names to be more consistent with
previous platforms (Lucas)

v3:
-Reorder bit defines to a more appropriate location.
 Change the comments. Confirm in the commit message that
 icp_irq_postinstall() need not go to
 ibx_irq_pre_postinstall() and ibx_irq_postinstall()
 as in earlier platforms. (Paulo)

Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
[Paulo: coding style bikesheds and rebases].
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530046343-30649-1-git-send-email-anusha.srivatsa@intel.com

In the next^W forthcoming patch, we will start to defer retiring the
request from the engine list if it is still active on the submission
backend. To preserve the semantics that after wait-for-idle completes
the system is idle and fully retired, we need to therefore wait for the
backends to idle before calling i915_retire_requests().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627115334.16282-1-chris@chris-wilson.co.uk

Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.

As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.

Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
  pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO

v2:
- Rebase on drm-tip after prep patch for this was merged there as
  requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)

v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency

v4:
- Rebase

v5:
- Detach AUX power wells from the INIT power domain. These power wells
  can only be enabled in a TC/TBT connected state and otherwise not
  needed during driver initialization.

v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
  Fix checkpatch warnings.

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com

Sink can be configured to calculate the CRC over the static frame and
compare with the CRC calculated and transmited in the VSC SDP by
source, if there is a mismatch sink will do a short pulse in HPD
and set DP_PSR_LINK_CRC_ERROR in DP_PSR_ERROR_STATUS.

Spec: 7723

v6:
andling DP_PSR_LINK_CRC_ERROR here and remove "bdw+" from commit
message

v4:
patch moved to after 'drm/i915/psr: Avoid PSR exit max time timeout'
to avoid touch in 2 patches EDP_PSR_DEBUG.

v3:
disabling PSR instead of exiting on error
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-5-jose.souza@intel.com

Specification requires that max time should be masked from bdw and
forward but it can be also safely enabled to hsw.
This will make PSR exits more deterministic and only when really
needed. If this was used to fix a issue in some panel than can
only self-refresh for a few seconds, that panel will interrupt
and assert one of the PSR errors handled in:
'drm/i915/psr: Handle PSR RFB storage error' and
'drm/i915/psr: Begin to handle PSR/PSR2 errors set by sink'

Spec: 21664

v4:
patch moved to before 'drm/i915/psr/bdw+: Enable CRC check in the
static frame on the sink side' to avoid touch in 2 patches
EDP_PSR_DEBUG.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-4-jose.souza@intel.com

Sink will interrupt source when it have any PSR error.
DP_PSR_VSC_SDP_UNCORRECTABLE_ERROR is a PSR2 but already
handling it here.
The only missing error to be handled is DP_PSR_LINK_CRC_ERROR that
will be taken in care in a futher patch.

v6:
not handling DP_PSR_LINK_CRC_ERROR here

v5:
handling all PSR errors here, so the commit message and
comment have changed

v3:
disabling PSR instead of exiting on error

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-3-jose.souza@intel.com

eDP spec states that sink device will do a short pulse in HPD
line when there is a PSR/PSR2 error that needs to be handled by
source, this is handling the first and most simples error:
DP_PSR_SINK_INTERNAL_ERROR.

Here taking the safest approach and disabling PSR(at least until
the next modeset), to avoid multiple rendering issues due to
bad pannels.

v5:
added lockdep_assert in psr_disable and renamed psr_disable()
to intel_psr_disable_locked()

v4:
Using CAN_PSR instead of HAS_PSR in intel_psr_short_pulse

v3:
disabling PSR instead of exiting on error
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-2-jose.souza@intel.com

It was only used in VLV/CHV so after the removal of the PSR support
for those platforms it is not necessary any more.

v7: Rebased
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-1-jose.souza@intel.com

Depending whether PSR1 or PSR2 was configured, we print a warning if the
corresponding control mmio indicated PSR was erroneously enabled. As
Chris pointed out, it makes more sense to check for both the mmio's
since we expect neither PSR1 nor PSR2 to be enabled when psr_activate() is
called.

v2: Read PSR2 control register only on supported platforms (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626090522.17682-1-dhinakaran.pandiyan@intel.com

Commit 5422b37c ("drm/i915/psr: Kill delays when activating psr
back.") switched from delayed work to the plain variant and while doing so
removed the check for work_busy() before scheduling a PSR activation.
This appears to cause consecutive executions of psr_activate() in this
scenario - after a worker picks up the PSR work item for execution and
before the work function can acquire the PSR mutex, a psr_flush() can
get hold of the mutex and schedule another PSR work. Without a psr_exit()
between the two psr_activate() calls, warning messages get printed.
Further, since we drop the mutex in the midst of psr_work() to wait for
PSR to idle, another work item can also get scheduled. Fix this by
returning if PSR was already active.

Fixes: 5422b37c ("drm/i915/psr: Kill delays when activating psr back.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106948
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625054741.3919-1-dhinakaran.pandiyan@intel.com

At some point we introduced the function pointers
on PSR code to help with VLV/CHV separation logic
because it had a different HW implementation from PSR.

Since all converged to HSW PSR and we dropped the
VLV/CHV support, let's also kill the useless function
pointers and leave the code cleaner.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626052536.15137-1-rodrigo.vivi@intel.com

So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
  link functionality, but suggests that these power wells need to be
  enabled already during display core initialization (Sequences to
  Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
  link training too: while the port is enabled with a DP link training
  test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
  link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
  functionality.

Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.

For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.

Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.

v2:
- Make sure DC states stay enabled when taking the ref on port A.
  (Ville)

v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
  add FIXME note for a simplification to avoid calling get_power_domains
  in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
 intel_ddi_get_power_domains() (Imre)]
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com

Due to how we only release the pining on the context state on
retirement and never track activity on the context vma itself, the
object can never be active at the point of release. Replace the
conditional transfer of ownership onto an active-reference with an
assert that the object is idle.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625100604.22598-2-chris@chris-wilson.co.uk

As we may cancel the ce->state allocation during context pinning (but
crucially after we mark ce as operational), that means we may be asked
to destroy a nonexistent ce->state. Given the choice in handing a
complex error path on pinning, and just ignoring the lack of state in
destroy, choice the latter for simplicity.
Reported-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625100604.22598-1-chris@chris-wilson.co.uk

If we avoid cleaning up the old state immediately in
intel_atomic_commit_tail() and defer it to a second task, we can avoid
taking heavily contended locks when the caller is ready to procede.
Subsequent modesets will wait for the cleanup operation (either directly
via the ordered modeset wq or indirectly through the atomic helperr)
which keeps the number of inflight cleanup tasks in check.

As an example, during reset an immediate modeset is performed to disable
the displays before the HW is reset, which must avoid struct_mutex to
avoid recursion. Moving the cleanup to a separate task, defers acquiring
the struct_mutex to after the GPU is running again, allowing it to
complete. Even in a few patches time (optimist!) when we no longer
require struct_mutex to unpin the framebuffers, it will still be good
practice to minimise the number of contention points along reset. The
mutex dependency still exists (as one modeset flushes the other), but in
the short term it resolves the deadlock for simple reset cases.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101600Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180623103951.23889-1-chris@chris-wilson.co.ukAcked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the guc_ctl_debug_flags, the ads struct is programmed only
when USES_GUC_SUBMISSION is satisfied. But, this has to be
programmed for all suspend/resume cases.
Remove the condition and program the ads struct for
both huc loading and guc submission.

This issue was noticed when CI threw errors for enable_guc=2
(load huc; disable submission)

v2:
- Change commit title.
- Correct the shifts. (Daniele)

Credits to: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Spotswood <john.a.spotswood@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NJohn Spotswood <john.a.spotswood@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1529691543-28606-1-git-send-email-anusha.srivatsa@intel.com

Alpha blending with alpha 0 and 0xff passes through
alpha math and rounding logic causing differences
compared to fully transparent or opaque plane,resulting
in CRC mismatch.
This WA on icl and above enables hardware to bypass alpha
math and rounding for per pixel alpha values of 00 and 0xff

v2: Fix patchwork checkpatch warnings.
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1529594036-25036-1-git-send-email-vandita.kulkarni@intel.com

Some MG PLL registers have fields that need to be preserved at their HW
default or BIOS programmed values. So make sure we preserve them.

v2:
- Add comment to icl_mg_pll_write() explaining the need for register
  masks. (Vandita)
- Fix patchwork checkpatch warning.

v3:
- Rebase on drm-tip.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v1)
Reviewed-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619164115.7835-1-imre.deak@intel.com

Atm we're zeroing out fields in MG_PLL_BIAS and MG_PLL_TDC_COLDST_BIAS
if refclk is 38.4MHz, whereas the spec tells us to preserve them.
Although the calculated values mostly match the register defaults even
for the 38.4MHz case, there are some differences wrt. what BIOS
programs (I noticed at least differences in the MG_PLL_BIAS/IREFTRIM and
MG_PLL_BIAS/BIASCAL_EN fields). In the lack of further info on how to
program these fields, just do what the spec says and preserve the BIOS
state.

v2:
- Preserve the BIOS programmed reg fields instead of programming them.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v1)
Reviewed-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615143911.31082-1-imre.deak@intel.com

This became dead code with commit 309bd8ed ("drm/i915: Reinstate
GMBUS and AUX interrupts on gen4/g4x").

v2: Move comment about HW behavior to where decision is made to enable
MSI (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523180435.18042-1-lucas.demarchi@intel.com

To aide debugging spurious EINVALs, include a debug message every time
we emit one from execbuf.

References: https://bugs.freedesktop.org/show_bug.cgi?id=106744Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621080150.8110-1-chris@chris-wilson.co.uk