If we're using VLANs and communications with the PF fail during
shutdown, we will leak memory because not all of the VLAN filters will
be removed. To eliminate this possibility, go through the list again
right before the module is removed and delete any leftover entries.

Change-ID: Id3b5315c47ca0a61ae123a96ff345d010bc41aed
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the VF driver is running in the host, the shutdown code is completely
broken. We cannot wait in our down routine for the PF to respond to our
requests, as its admin queue task will never run while we hold the lock.

Instead, we schedule operations, then let the watchdog take care of
shutting things down. If the driver is being removed, then wait in the
remove routine until the watchdog is done before continuing.

Change-ID: I93a58d17389e8d6b58f21e430b56ed7b4590b2c5
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These messages may be triggered during normal init of the driver if the
PF or FW take a long time to respond. There's nothing really wrong, so
don't freak people out logging messages.

If the communication channel really is dead, then we'll retry a few
times and give up. This will log a different more scary message that
should cause consternation. This allows the user to more easily detect a
genuine failure.

Change-ID: I6e2b758d4234a3a09c1015c82c8f2442a697cbdb
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These functions are redundant and duplicate functionality found in
i40evf_free_all_[tx|rx]_resources.

Change-ID: Ia199908926d7a1a4b8247f75f89b5da24c9b149c
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If VF drivers are loaded in the host OS, the call to pci_disable_sriov()
will cause these drivers' remove routines to be called. If the PF driver
has already freed VF resources before this happens, then the VF remove
routine can't properly communicate with the PF driver causing all sorts
of mayhem and error messages and hurt feelings.

To fix this, we move the call to pci_disable_sriov() up to the top of
the function and let it complete before freeing any VF resources.

Change-ID: I397c3997a00f6408e32b7735273911e499600236
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ying Xue says:

====================
remove nl_sk_hash_lock from netlink socket

After tipc socket successfully avoids the involvement of an extra lock
with rhashtable_lookup_insert(), it's possible for netlink socket to
remove its hash socket lock now. But as netlink socket needs a compare
function to look for an object, we first introduce a new function
called rhashtable_lookup_compare_insert() in commit #1 which is
implemented based on original rhashtable_lookup_insert(). We
subsequently remove nl_sk_hash_lock from netlink socket with the new
introduced function in commit #2. Lastly, as Thomas requested, we add
commit #3 to indicate the implementation of what the grow and shrink
decision function must enforce min/max shift.

v2:
 As Thomas pointed out, there was a race between checking portid and
 then setting it in commit #2. Now use socket lock to make the process
 of both checking and setting portid atomic, and then eliminate the
 race.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As commit c0c09bfd ("rhashtable: avoid unnecessary wakeup for
worker queue") moves condition statements of verifying whether hash
table size exceeds its maximum threshold or reaches its minimum
threshold from resizing functions to resizing decision functions,
we should add a note in rhashtable.h to indicate the implementation
of what the grow and shrink decision function must enforce min/max
shift, otherwise, it's failed to take min/max shift's set watermarks
into effect.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As rhashtable_lookup_compare_insert() can guarantee the process
of search and insertion is atomic, it's safe to eliminate the
nl_sk_hash_lock. After this, object insertion or removal will
be protected with per bucket lock on write side while object
lookup is guarded with rcu read lock on read side.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a new function called rhashtable_lookup_compare_insert()
which is very similar to rhashtable_lookup_insert(). But the former
makes use of users' given compare function to look for an object,
and then inserts it into hash table if found. As the entire process
of search and insertion is under protection of per bucket lock, this
can help users to avoid the involvement of extra lock.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pankaj Gupta says:

====================
Increase the limit of tuntap queues

Networking under KVM works best if we allocate a per-vCPU rx and tx
queue in a virtual NIC. This requires a per-vCPU queue on the host side.
Modern physical NICs have multiqueue support for large number of queues.
To scale vNIC to run multiple queues parallel to maximum number of vCPU's
we need to increase number of queues support in tuntap.

Changes from v4:
PATCH2: Michael.S.Tsirkin - Updated change comment message.

Changes from v3:
PATCH1: Michael.S.Tsirkin - Some cleanups and updated commit message.
                            Perf numbers on 10 Gbs NIC
Changes from v2:
PATCH 3: David Miller     - flex array adds extra level of indirection
                            for preallocated array.(dropped, as flow array
			    is allocated using kzalloc with failover to zalloc).
Changes from v1:
PATCH 2: David Miller     - sysctl changes to limit number of queues
                            not required for unprivileged users(dropped).

Changes from RFC
PATCH 1: Sergei Shtylyov  - Add an empty line after declarations.
PATCH 2: Jiri Pirko -       Do not introduce new module paramaters.
	 Michael.S.Tsirkin- We can use sysctl for limiting max number
                            of queues.

This series is to increase the number of tuntap queues. Original work is being
done by 'jasowang@redhat.com'. I am taking this 'https://lkml.org/lkml/2013/6/19/29'
patch series as a reference. As per discussion in the patch series:

There were two reasons which prevented us from increasing number of tun queues:

- The netdev_queue array in netdevice were allocated through kmalloc, which may
  cause a high order memory allocation too when we have several queues.
  E.g. sizeof(netdev_queue) is 320, which means a high order allocation would
  happens when the device has more than 16 queues.

- We store the hash buckets in tun_struct which results a very large size of
  tun_struct, this high order memory allocation fail easily when the memory is
  fragmented.

The patch 60877a32 increases the number of tx
queues. Memory allocation fallback to vzalloc() when kmalloc() fails.

This series tries to address following issues:

- Increase the number of netdev_queue queues for rx similarly its done for tx
  queues by falling back to vzalloc() when memory allocation with kmalloc() fails.

- Increase number of queues to 256, maximum number is equal to maximum number
  of vCPUS allowed in a guest.

I have also done testing with multiple parallel Netperf sessions for different
combination of queues and CPU's. It seems to be working fine without much increase
in cpu load with increase in number of queues. I also see good increase in throughput
with increase in number of queues. Though i had limitation of 8 physical CPU's.

For this test: Two Hosts(Host1 & Host2) are directly connected with cable
Host1 is running Guest1. Data is sent from Host2 to Guest1 via Host1.

Host kernel: 3.19.0-rc2+, AMD Opteron(tm) Processor 6320
NIC : Emulex Corporation OneConnect 10Gb NIC (be3)

Patch Applied  %usr   %nice    %sys %iowait    %irq   %soft  %steal  %guest  %gnice   %idle  throughput
Single Queue, 2 vCPU's
-------------
Before Patch :all    0.19    0.00    0.16    0.07    0.04    0.10    0.00    0.18    0.00   99.26  57864.18
After  Patch :all    0.99    0.00    0.64    0.69    0.07    0.26    0.00    1.58    0.00   95.77  57735.77

With 2 Queues, 2 vCPU's
---------------
Before Patch :all    0.19    0.00    0.19    0.10    0.04    0.11    0.00    0.28    0.00   99.08  63083.09
After  Patch :all    0.87    0.00    0.73    0.78    0.09    0.35    0.00    2.04    0.00   95.14  62917.03

With 4 Queues, 4 vCPU's
--------------
Before Patch :all    0.20    0.00    0.21    0.11    0.04    0.12    0.00    0.32    0.00   99.00  80865.06
After  Patch :all    0.71    0.00    0.93    0.85    0.11    0.51    0.00    2.62    0.00   94.27  86463.19

With 8 Queues, 8 vCPU's
--------------
Before Patch :all    0.19    0.00    0.18    0.09    0.04    0.11    0.00    0.23    0.00   99.17  86795.31
After  Patch :all    0.65    0.00    1.18    0.93    0.13    0.68    0.00    3.38    0.00   93.05  89459.93

With 16 Queues, 8 vCPU's
--------------
After  Patch :all    0.61    0.00    1.59    0.97    0.18    0.92    0.00    4.32    0.00   91.41  120951.60
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Networking under kvm works best if we allocate a per-vCPU RX and TX
queue in a virtual NIC. This requires a per-vCPU queue on the host side.

It is now safe to increase the maximum number of queues.
Preceding patch: 'net: allow large number of rx queues'
made sure this won't cause failures due to high order memory
allocations. Increase it to 256: this is the max number of vCPUs
KVM supports.

Size of tun_struct changes from 8512 to 10496 after this patch. This keeps
pages allocated for tun_struct before and after the patch to 3.
Signed-off-by: NPankaj Gupta <pagupta@redhat.com>
Reviewed-by: NDavid Gibson <dgibson@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_alloc_rx_queues() uses kcalloc() to allocate memory
for "struct netdev_queue *_rx" array.
If we are doing large rx queue allocation kcalloc() might
fail, so this patch does a fallback to vzalloc().
Similar implementation is done for tx queue allocation in
netif_alloc_netdev_queues().

We avoid failure of high order memory allocation
with the help of vzalloc(), this allows us to do large
rx and tx queue allocation which in turn helps us to
increase the number of queues in tun.

As vmalloc() adds overhead on a critical network path,
__GFP_REPEAT flag is used with kzalloc() to do this fallback
only when really needed.
Signed-off-by: NPankaj Gupta <pagupta@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NDavid Gibson <dgibson@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The deleted lines are called from a function which is called:
1) Only through __team_options_register via team_options_register and
2) Only during initialization / mode initialization when there are no
ports attached.
Therefore the ports list is guarenteed to be empty and this code will
never be executed.
Signed-off-by: NKenneth Williams <ken@williamsclan.us>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the function teql_neigh_release() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the function aead_entries() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
bridge: support for vlan range in setlink/dellink

This series adds new flags in IFLA_BRIDGE_VLAN_INFO to indicate
vlan range.

Will post corresponding iproute2 patches if these get accepted.

v1-> v2
    - changed patches to use a nested list attribute
    IFLA_BRIDGE_VLAN_INFO_LIST as suggested by scott feldman
    - dropped notification changes from the series. Will post them
    separately after this range message is accepted.

v2 -> v3
    - incorporated some review feedback
    - include patches to fill vlan ranges during getlink
    - Dropped IFLA_BRIDGE_VLAN_INFO_LIST. I think it may get
    confusing to userspace if we introduce yet another way to
    send lists. With getlink already sending nested
    IFLA_BRIDGE_VLAN_INFO in IFLA_AF_SPEC, It seems better to
    use the existing format for lists and just use the flags from v2
    to mark vlan ranges
====================
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NWilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds new function to pack vlans into ranges
whereever applicable using the flags BRIDGE_VLAN_INFO_RANGE_BEGIN
and BRIDGE VLAN_INFO_RANGE_END

Old vlan packing code is moved to a new function and continues to be
called when filter_mask is RTEXT_FILTER_BRVLAN.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This filter is same as RTEXT_FILTER_BRVLAN except that it tries
to compress the consecutive vlans into ranges.

This helps on systems with large number of configured vlans.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes bridge IFLA_AF_SPEC netlink attribute parser to
look for more than one IFLA_BRIDGE_VLAN_INFO attribute. This allows
userspace to pack more than one vlan in the setlink msg.

The dumps were already sending more than one vlan info in the getlink msg.

This patch also adds bridge_vlan_info flags BRIDGE_VLAN_INFO_RANGE_BEGIN and
BRIDGE_VLAN_INFO_RANGE_END to indicate start and end of vlan range

This patch also deletes unused ifla_br_policy.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes some unused arrays from the netfront private
data structures. These arrays were used in "flip" receive mode.
Signed-off-by: NVincenzo Maffione <v.maffione@gmail.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Failing to reinitialize on wakeup results in loss of network connectivity for
vmxnet3 interface.
Signed-off-by: NSrividya Murali <smurali@vmware.com>
Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Reviewed-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the empty array element initializer and size the array with
BOND_OPT_LAST so the compiler will complain if more elements are in
there than should be.

An interesting unwanted side effect of this initializer is that if one
inserts new options into the middle of the array then this initializer
will zero out the option that equals BOND_OPT_TLB_DYNAMIC_LB+1.

Example:
Extend the OPTS enum:
enum {
   ...
   BOND_OPT_TLB_DYNAMIC_LB,
   BOND_OPT_LACP_NEW1,
   BOND_OPT_LAST
};

Now insert into bond_opts array:
static const struct bond_option bond_opts[] = {
      ...
      [BOND_OPT_LACP_RATE] = { .... unchanged stuff .... },
      [BOND_OPT_LACP_NEW1] = { ... new stuff ... },
      ...
      [BOND_OPT_TLB_DYNAMIC_LB] = { .... unchanged stuff ....},
      { } // MARK A
};

Since BOND_OPT_LACP_NEW1 = BOND_OPT_TLB_DYNAMIC_LB+1, the last
initializer (MARK A) will overwrite the contents of BOND_OPT_LACP_NEW1
and can be easily viewed with the crash utility.
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ying Xue says:

====================
tipc: make tipc support namespace

This patchset aims to add net namespace support for TIPC stack.

Currently TIPC module declares the following global resources:
- TIPC network idenfication number
- TIPC node table
- TIPC bearer list table
- TIPC broadcast link
- TIPC socket reference table
- TIPC name service table
- TIPC node address
- TIPC service subscriber server
- TIPC random value
- TIPC netlink

In order that TIPC is aware of namespace, above each resource must be
allocated, initialized and destroyed inside per namespace. Therefore,
the major works of this patchset are to isolate these global resources
and make them private for each namespace. However, before these changes
come true, some necessary preparation works must be first done: convert
socket reference table with generic rhashtable, cleanup core.c and
core.h files, remove unnecessary wrapper functions for kernel timer
interfaces and so on.

It should be noted that commit ##1 ("tipc: fix bug in broadcast
retransmit code") was already submitted to 'net' tree, so please see
below link:

http://patchwork.ozlabs.org/patch/426717/

Since it is prerequisite for the rest of the series to apply, I
prepend them to the series.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tipc module only allows users sitting on "init_net" namespace
to configure it through netlink interface. But now almost each tipc
component is able to be aware of net namespace, so it's time to open
the permission for users residing in other namespaces, allowing them
to configure their own tipc stack instance through netlink interface.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After namespace is supported, each namespace should own its private
random value. So the global variable representing the random value
must be moved to tipc_net structure.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC establishes one subscriber server which allows users to subscribe
their interesting name service status. After tipc supports namespace,
one dedicated tipc stack instance is created for each namespace, and
each instance can be deemed as one independent TIPC node. As a result,
subscriber server must be built for each namespace.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If net namespace is supported in tipc, each namespace will be treated
as a separate tipc node. Therefore, every namespace must own its
private tipc node address. This means the "tipc_own_addr" global
variable of node address must be moved to tipc_net structure to
satisfy the requirement. It's turned out that users also can assign
node address for every namespace.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC name table is used to store the mapping relationship between
TIPC service name and socket port ID. When tipc supports namespace,
it allows users to publish service names only owned by a certain
namespace. Therefore, every namespace must have its private name
table to prevent service names published to one namespace from being
contaminated by other service names in another namespace. Therefore,
The name table global variable (ie, nametbl) and its lock must be
moved to tipc_net structure, and a parameter of namespace must be
added for necessary functions so that they can obtain name table
variable defined in tipc_net structure.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now tipc socket table is statically allocated as a global variable.
Through it, we can look up one socket instance with port ID, insert
a new socket instance to the table, and delete a socket from the
table. But when tipc supports net namespace, each namespace must own
its specific socket table. So the global variable of socket table
must be redefined in tipc_net structure. As a concequence, a new
socket table will be allocated when a new namespace is created, and
a socket table will be deallocated when namespace is destroyed.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC broadcast link is statically established and its relevant states
are maintained with the global variables: "bcbearer", "bclink" and
"bcl". Allowing different namespace to own different broadcast link
instances, these variables must be moved to tipc_net structure and
broadcast link instances would be allocated and initialized when
namespace is created.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bearer list defined as a global variable is used to store bearer
instances. When tipc supports net namespace, bearers created in
one namespace must be isolated with others allocated in other
namespaces, which requires us that the bearer list(bearer_list)
must be moved to tipc_net structure. As a result, a net namespace
pointer has to be passed to functions which access the bearer list.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Global variables associated with node table are below:
- node table list (node_htable)
- node hash table list (tipc_node_list)
- node table lock (node_list_lock)
- node number counter (tipc_num_nodes)
- node link number counter (tipc_num_links)

To make node table support namespace, above global variables must be
moved to tipc_net structure in order to keep secret for different
namespaces. As a consequence, these variables are allocated and
initialized when namespace is created, and deallocated when namespace
is destroyed. After the change, functions associated with these
variables have to utilize a namespace pointer to access them. So
adding namespace pointer as a parameter of these functions is the
major change made in the commit.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Involve namespace infrastructure, make the "tipc_net_id" global
variable aware of per namespace, and rename it to "net_id". In
order that the conversion can be successfully done, an instance
of networking namespace must be passed to relevant functions,
allowing them to access the "net_id" variable of per namespace.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to make tipc socket table aware of namespace, a networking
namespace instance must be passed to tipc_sk_lookup(), allowing it
to look up tipc socket instance with a given port ID from a concrete
socket table. However, as now tipc_sk_timeout() only has one port ID
parameter and is not namespace aware, it's unable to obtain a correct
socket instance through tipc_sk_lookup() just with a port ID,
especially after namespace is completely supported.

If port ID is replaced with socket instance as tipc_sk_timeout()'s
parameter, it's unnecessary to look up socket table. But as the timer
handler - tipc_sk_timeout() is run asynchronously, socket reference
must be held before its timer is launched, and must be carefully
checked to identify whether the socket reference needs to be put or
not when its timer is terminated.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the works of initializing and shutting down tipc module are done
in core.h and core.c files, so all stuffs which are not closely
associated with the two tasks should be moved to appropriate places.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not only some wrapper function like k_term_timer() is empty, but also
some others including k_start_timer() and k_cancel_timer() don't return
back any value to its caller, what's more, there is no any component
in the kernel world to do such thing. Therefore, these timer interfaces
defined in tipc module should be purged.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove redundant wrapper functions like tipc_core_start() and
tipc_core_stop(), and directly move them to their callers, such
as tipc_init() and tipc_exit(), having us clearly know what are
really done in both initialization and deinitialzation functions.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 58dc55f2 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.

In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.

In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>