Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 24 5月, 2011 1 次提交
  3. 22 5月, 2011 17 次提交
  5. 21 5月, 2011 1 次提交
    • L
      sanitize <linux/prefetch.h> usage · 268bb0ce
      由 Linus Torvalds 提交于 
      Commit e66eed65 ("list: remove prefetching from regular list
iterators") removed the include of prefetch.h from list.h, which
uncovered several cases that had apparently relied on that rather
obscure header file dependency.

So this fixes things up a bit, using

   grep -L linux/prefetch.h $(git grep -l '[^a-z_]prefetchw*(' -- '*.[ch]')
   grep -L 'prefetchw*(' $(git grep -l 'linux/prefetch.h' -- '*.[ch]')

to guide us in finding files that either need <linux/prefetch.h>
inclusion, or have it despite not needing it.

There are more of them around (mostly network drivers), but this gets
many core ones.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      268bb0ce
  7. 20 5月, 2011 5 次提交
  9. 18 5月, 2011 5 次提交
  11. 17 5月, 2011 2 次提交
  13. 16 5月, 2011 1 次提交
    • Y
      x86, apic: Fix spurious error interrupts triggering on all non-boot APs · e503f9e4
      由 Youquan Song 提交于 
      This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.

According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.

The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.

When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.

This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.

This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Acked-by: NYong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.comSigned-off-by: NIngo Molnar <mingo@elte.hu>
      e503f9e4
  15. 14 5月, 2011 1 次提交
  17. 13 5月, 2011 2 次提交
    • C
      x86: Fix UV BAU for non-consecutive nasids · 77ed23f8
      由 Cliff Wickman 提交于 
      This is a fix for the SGI Altix-UV Broadcast Assist Unit code,
which is used for TLB flushing.

Certain hardware configurations (that customers are ordering)
cause nasids (numa address space id's) to be non-consecutive.
Specifically, once you have more than 4 blades in a IRU
(Individual Rack Unit - or 1/2 rack) but less than the maximum
of 16, the nasid numbering becomes non-consecutive.  This
currently results in a 'catastrophic error' (CATERR) detected by
the firmware during OS boot.  The BAU is generating an 'INTD'
request that is targeting a non-existent nasid value. Such
configurations may also occur when a blade is configured off
because of hardware errors. (There is one UV hub per blade.)

This patch is required to support such configurations.

The problem with the tlb_uv.c code is that is using the
consecutive hub numbers as indices to the BAU distribution bit
map. These are simply the ordinal position of the hub or blade
within its partition.  It should be using physical node numbers
(pnodes), which correspond to the physical nasid values. Use of
the hub number only works as long as the nasids in the partition
are consecutive and increase with a stride of 1.

This patch changes the index to be the pnode number, thus
allowing nasids to be non-consecutive.
It also provides a table in local memory for each cpu to
translate target cpu number to target pnode and nasid.
And it improves naming to properly reflect 'node' and 'uvhub'
versus 'nasid'.
Signed-off-by: NCliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1QJmxX-0002Mz-Fk@eag09.americas.sgi.comSigned-off-by: NIngo Molnar <mingo@elte.hu>
      77ed23f8
    • S
      x86,xen: introduce x86_init.mapping.pagetable_reserve · 279b706b
      由 Stefano Stabellini 提交于 
      Introduce a new x86_init hook called pagetable_reserve that at the end
of init_memory_mapping is used to reserve a range of memory addresses for
the kernel pagetable pages we used and free the other ones.

On native it just calls memblock_x86_reserve_range while on xen it also
takes care of setting the spare memory previously allocated
for kernel pagetable pages from RO to RW, so that it can be used for
other purposes.

A detailed explanation of the reason why this hook is needed follows.

As a consequence of the commit:

commit 4b239f45
Author: Yinghai Lu <yinghai@kernel.org>
Date:   Fri Dec 17 16:58:28 2010 -0800

    x86-64, mm: Put early page table high

at some point init_memory_mapping is going to reach the pagetable pages
area and map those pages too (mapping them as normal memory that falls
in the range of addresses passed to init_memory_mapping as argument).
Some of those pages are already pagetable pages (they are in the range
pgt_buf_start-pgt_buf_end) therefore they are going to be mapped RO and
everything is fine.
Some of these pages are not pagetable pages yet (they fall in the range
pgt_buf_end-pgt_buf_top; for example the page at pgt_buf_end) so they
are going to be mapped RW.  When these pages become pagetable pages and
are hooked into the pagetable, xen will find that the guest has already
a RW mapping of them somewhere and fail the operation.
The reason Xen requires pagetables to be RO is that the hypervisor needs
to verify that the pagetables are valid before using them. The validation
operations are called "pinning" (more details in arch/x86/xen/mmu.c).

In order to fix the issue we mark all the pages in the entire range
pgt_buf_start-pgt_buf_top as RO, however when the pagetable allocation
is completed only the range pgt_buf_start-pgt_buf_end is reserved by
init_memory_mapping. Hence the kernel is going to crash as soon as one
of the pages in the range pgt_buf_end-pgt_buf_top is reused (b/c those
ranges are RO).

For this reason we need a hook to reserve the kernel pagetable pages we
used and free the other ones so that they can be reused for other
purposes.
On native it just means calling memblock_x86_reserve_range, on Xen it
also means marking RW the pagetable pages that we allocated before but
that haven't been used before.

Another way to fix this is without using the hook is by adding a 'if
(xen_pv_domain)' in the 'init_memory_mapping' code and calling the Xen
counterpart, but that is just nasty.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
      279b706b
  19. 12 5月, 2011 1 次提交
  21. 11 5月, 2011 4 次提交