- 24 10月, 2015 1 次提交
-
-
由 Michael Chan 提交于
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac() to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV. Reported-by: NJim Hull <jim.hull@hpe.com> Tested-by: NJim Hull <jim.hull@hpe.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 10月, 2015 30 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue由 David S. Miller 提交于
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-10-23 This series contains updates to i40e, i40evf, if_link, ixgbe and ixgbevf. Anjali adds a workaround to drop any flow control frames from being transmitted from any VSI, so that a malicious VF cannot send flow control or PFC packets out on the wire. Also fixed a bug in debugfs by grabbing the filter list lock before adding or deleting a filter. Akeem fixes an issue where we were unconditionally returning VEB bridge mode before allowing LB in the add VSI routine, resolve by checking if the bridge is actually in VEB mode first. Mitch fixed an issue where the incorrect structure was being used for VLAN filter list, which meant the VLAN filter list did not get processed correctly and VLAN filters would not be re-enabled after any kind of reset. Helin fixed a problem of possibly getting inconsistent flow control status after a PF reset. The issue was requested_mode was being set with a default value during probe, but the hardware state could be a different value from this mode. Carolyn fixed a problem where the driver output of the OEM version string varied from the other tools. Jean Sacren fixes up kernel documentation by fixing function header comments to match actual variables used in the functions. Also cleaned up variable initialization, when the variable would be over-written immediately. Hiroshi Shimanoto provides three patches to add "trusted" VF by adding netlink directives and an NDO entry. Then implement these new controls in ixgbe and ixgbevf. This series has gone through several iterations to address all the suggested community changes and concerns. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Roopa Prabhu says: ==================== mpls: multipath support This patch adds support for MPLS multipath routes. Includes following changes to support multipath: - splits struct mpls_route into 'struct mpls_route + struct mpls_nh'. - struct mpls_nh represents a mpls nexthop label forwarding entry - Adds support to parse/fill RTA_MULTIPATH netlink attribute for multipath routes similar to ipv4/v6 fib - In the process of restructuring, this patch also consistently changes all labels to u8 $ip -f mpls route add 100 nexthop as 200 via inet 10.1.1.2 dev swp1 \ nexthop as 700 via inet 10.1.1.6 dev swp2 \ nexthop as 800 via inet 40.1.1.2 dev swp3 $ip -f mpls route show 100 nexthop as to 200 via inet 10.1.1.2 dev swp1 nexthop as to 700 via inet 10.1.1.6 dev swp2 nexthop as to 800 via inet 40.1.1.2 dev swp3 ==================== Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com> Acked-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Robert Shearman 提交于
Change the selection of a multipath route to use a flow-based hash. This more suitable for traffic sensitive to reordering within a flow (e.g. TCP, L2VPN) and whilst still allowing a good distribution of traffic given enough flows. Selection of the path for a multipath route is done using a hash of: 1. Label stack up to MAX_MP_SELECT_LABELS labels or up to and including entropy label, whichever is first. 2. 3-tuple of (L3 src, L3 dst, proto) from IPv4/IPv6 header in MPLS payload, if present. Naturally, a 5-tuple hash using L4 information in addition would be possible and be better in some scenarios, but there is a tradeoff between looking deeper into the packet to achieve good distribution, and packet forwarding performance, and I have erred on the side of the latter as the default. Signed-off-by: NRobert Shearman <rshearma@brocade.com> Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Roopa Prabhu 提交于
This patch adds support for MPLS multipath routes. Includes following changes to support multipath: - splits struct mpls_route into 'struct mpls_route + struct mpls_nh' - 'struct mpls_nh' represents a mpls nexthop label forwarding entry - moves mpls route and nexthop structures into internal.h - A mpls_route can point to multiple mpls_nh structs - the nexthops are maintained as a array (similar to ipv4 fib) - In the process of restructuring, this patch also consistently changes all labels to u8 - Adds support to parse/fill RTA_MULTIPATH netlink attribute for multipath routes similar to ipv4/v6 fib - In this patch, the multipath route nexthop selection algorithm simply returns the first nexthop. It is replaced by a hash based algorithm from Robert Shearman in the next patch - mpls_route_update cleanup: remove 'dev' handling in mpls_route_update. mpls_route_update though implemented to update based on dev, it was never used that way. And the dev handling gets tricky with multiple nexthops. Cannot match against any single nexthops dev. So, this patch removes the unused 'dev' handling in mpls_route_update. - dead route/path handling will be implemented in a subsequent patch Example: $ip -f mpls route add 100 nexthop as 200 via inet 10.1.1.2 dev swp1 \ nexthop as 700 via inet 10.1.1.6 dev swp2 \ nexthop as 800 via inet 40.1.1.2 dev swp3 $ip -f mpls route show 100 nexthop as to 200 via inet 10.1.1.2 dev swp1 nexthop as to 700 via inet 10.1.1.6 dev swp2 nexthop as to 800 via inet 40.1.1.2 dev swp3 Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com> Acked-by: NRobert Shearman <rshearma@brocade.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Neil Armstrong says: ==================== Refactor nested mdiobus read/write functions In order to avoid locked signal false positive for nested mdiobus read/write calls, nested code was introduced in mv88e6xxx and mdio-mux. But mv88e6060 also needs such nested mdiobus read/write calls. For sake of refactoring, introduce nested variants of mdiobus read/write and make them used by mv88e6xxx and mv88e6060. In a next patch, mdio-mux should also use these variant calls. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Armstrong 提交于
Like mv88e6xxx and mdio-mux, to avoid lockdep give false positives because of nested MDIO busses, switch to previously introduced nested mdiobus_read/write variants. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Armstrong 提交于
Make the mv88e6xxx driver use the previously introduced nested variants of mdiobus_read/write functions. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Armstrong 提交于
Since nested variants of mdiobus_read/write are used in multiple drivers, add nested variants in the mdiobus core. Suggested-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hiroshi Shimamoto 提交于
The limitation of the number of multicast address for VF is not enough for the large scale server with SR-IOV feature. IPv6 requires the multicast MAC address for each IP address to handle the Neighbor Solicitation message. We couldn't assign over 30 IPv6 addresses to a single VF. This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE, to update multicast mode of VF. This adds 3 modes; - NONE only L2 exact match addresses or Flow Director enabled - MULTI BAM and ROMPE set - ALLMULTI BAM, ROMPE and MPE set If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI to request PF to update xcast mode to enable VF multicast promiscuous mode. On the other hand, enabling VF multicast promiscuous mode may affect security and performance in the network of the NIC. Only trusted VF can enable multicast promiscuous mode. The behavior of untrusted VF is the same as previous version. Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Hiroshi Shimamoto 提交于
Implements the new netdev op to trust VF in ixgbe. The administrator can turn on and off VF trusted by ip command which supports trust message. # ip link set dev eth0 vf 1 trust on or # ip link set dev eth0 vf 1 trust off Send a ping to reset VF on changing the status of trusting. VF driver will reconfigure its features on reset. Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Grygorii Strashko 提交于
There is no reasons to probe cpsw from late_initcall level and it's not recommended. Hence, use module_platform_driver() to register and probe cpsw driver from module_init() level. Cc: Tony Lindgren <tony@atomide.com> Acked-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hiroshi Shimamoto 提交于
Add netlink directives and ndo entry to trust VF user. This controls the special permission of VF user. The administrator will dedicatedly trust VF user to use some features which impacts security and/or performance. The administrator never turn it on unless VF user is fully trusted. CC: Sy Jong Choi <sy.jong.choi@intel.com> Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com> Acked-by: NGreg Rose <gregory.v.rose@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Eric Dumazet 提交于
Multiple cpus can process duplicates of incoming ACK messages matching a SYN_RECV request socket. This is a rare event under normal operations, but definitely can happen. Only one must win the race, otherwise corruption would occur. To fix this without adding new atomic ops, we use logic in inet_ehash_nolisten() to detect the request was present in the same ehash bucket where we try to insert the new child. If request socket was not found, we have to undo the child creation. This actually removes a spin_lock()/spin_unlock() pair in reqsk_queue_unlink() for the fast path. Fixes: e994b2f0 ("tcp: do not lock listener to process SYN packets") Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jean Sacren 提交于
The commit 3092e5e4cc79 ("i40e: add little endian conversion for checksum") fixed the checksum bug on big-endian architecture. But we should not execute cpu_to_le16() unconditionally. Thus, put cpu_to_le16() under certain condition. Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Signed-off-by: NJean Sacren <sakiwit@gmail.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jean Sacren 提交于
In both i40e_calc_nvm_checksum() and i40e_update_nvm_checksum(), the local variables designated by 'ret_code' are overwritten immediately. As such, they should merely be declared. Signed-off-by: NJean Sacren <sakiwit@gmail.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jean Sacren 提交于
In i40evf_msix_aq(), the first two lines of rd32() are mainly to clear the registers. If we initialize 'val' at this point, it will be overwritten immediately. We shall simply discard the return value here. When we initialize 'val', we might as well include the mask in one step. Signed-off-by: NJean Sacren <sakiwit@gmail.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jean Sacren 提交于
The following kernel-doc arguments for their respective functions are missing: 1) @cd_type_cmd_tso_mss for i40e_tso(); 2) @cd_type_cmd_tso_mss for i40e_tsyn(); 3) @tx_ring for i40e_tx_enable_csum(). Add them all for the kernel-doc requirement. Signed-off-by: NJean Sacren <sakiwit@gmail.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jean Sacren 提交于
@flush has been missing since the inception of i40evf_irq_enable(). Add it for the kernel doc. Signed-off-by: NJean Sacren <sakiwit@gmail.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Andy Shevchenko 提交于
Instead of using a custom approach change the code to use %*ph format specifier. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Catherine Sullivan 提交于
Bump up the version... Change-ID: Ib8d501021671ba20250115ed54330e2c182255b7 Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Akeem G Abodunrin 提交于
If a call to enable SR-IOV in the kernel failed, we need to disable I40E_FLAG_VEB_MODE_ENABLED, so that bridge mode could fall back to VEPA, which is a default. Change-ID: I12b6f776769506db85b29bea94b9c88d0b5ee65e Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Carolyn Wyborny 提交于
This patch fixes a problem where the driver output of the OEM version string varied from the other tools. The mask value and the order of operations were incorrect, per the original change request. Without this patch, the version string will appear incorrect from the driver. Change-ID: Ie1ca6485284b4ce3b57e5a99b18b7641617c7ef7 Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Helin Zhang 提交于
This patch fixes a problem of possibly getting inconsistent flow control statuses after a PF reset. Requested_mode was being set with a default value during probing, but the initial HW state could be different from this mode. Change-ID: I772bf07b78616e87086418d4bd87954b66fa17cd Signed-off-by: NHelin Zhang <helin.zhang@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Mitch Williams 提交于
Not sure how this compiles at all. Use the correct struct for manipulating the VLAN filter list. Without this, the VLAN filter list doesn't get processed correctly, and VLAN filters will not be re-enabled after any kind of reset. Change-ID: Iceff2dc089f303058fb71ecb08419eed471e0e90 Signed-off-by: NMitch Williams <mitch.a.williams@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Akeem G Abodunrin 提交于
Fix i40e_is_vsi_uplink_mode_veb to check if bridge is actually in VEB mode before allowing LB in the add VSI routine, instead of unconditionally returning VEB bridge mode. Change-ID: I162397b1bdd02367735fe9baaeb51465be2a3ce9 Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Anjali Singhai Jain 提交于
The new code flow requires us to grab the filter list lock before adding/deleting the filter. Change-ID: I4eaef508ab4da2d1b2e23f20f2a78d931d5b6aeb Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Anjali Singhai Jain 提交于
This patch adds a workaround to drop any flow control frames from being transmitted from any VSI. FW can still send flow control frames if flow control is enabled. With this patch in place a malicious VF cannot send flow control or PFC packets out on the wire. Change-ID: I4303b24e98b93066d2767fec24dfe78be591c277 Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com> Tested-by: NAndrew Bowers <andrewx.bowers@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Paolo Abeni 提交于
Currently adding a new ipv4 address always cause the creation of the related network route, with default metric. When a host has multiple interfaces on the same network, multiple routes with the same metric are created. If the userspace wants to set specific metric on each routes, i.e. giving better metric to ethernet links in respect to Wi-Fi ones, the network routes must be deleted and recreated, which is error-prone. This patch implements the support for IFA_F_NOPREFIXROUTE for ipv4 address. When an address is added with such flag set, no associated network route is created, no network route is deleted when said IP is gone and it's up to the user space manage such route. Signed-off-by: NPaolo Abeni <pabeni@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Broadcom ethernet driver for the new family of NetXtreme-C/E ethernet devices. v5: - Removed empty blank lines at end of files (noted by David Miller). - Moved busy poll helper functions to bnxt.h to at least make the .c file look less cluttered with #ifdef (noted by Stephen Hemminger). v4: - Broke up 2 long message strings with "\n" (suggested by John Linville) - Constify an array of strings (suggested by Stephen Hemminger) - Improve bnxt_vf_pciid() (suggested by Stephen Hemminger) - Use PCI_VDEVICE() to populate pci_device_id table for more compact source. v3: - Fixed 2 more sparse warnings. - Removed some unused structures in .h files. v2: - Fixed all kbuild test robot reported warnings. - Fixed many of the checkpatch.pl errors and warnings. - Fixed the Kconfig description (noted by Dmitry Kravkov). Acked-by: NEddie Wai <eddie.wai@broadcom.com> Acked-by: NJeffrey Huang <huangjw@broadcom.com> Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
It is preferable to have a common debugfs interface for DSA or switchdev instead of a driver specific one. Thus remove the mv88e6xxx debug code. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 10月, 2015 9 次提交
-
-
由 David S. Miller 提交于
Vivien Didelot says: ==================== net: dsa: implement port_fdb_dump in drivers Not all switch chips provide a Get Next kind of operation to dump FDB entries. It is preferred to let the driver handle the dump operation the way it works best for the chip. Thus, drop port_fdb_getnext and implement the port_fdb_dump operation in DSA, which pushes the switchdev FDB dump callback down to the drivers. mv88e6xxx is the only driver affected and is updated accordingly. v3 -> v4: fix rejects on latest net-next v2 -> v3: opencode switchdev_obj_dump_cb_t to avoid multiple typedef; use ether_addr_copy in fdb_dump v1 -> v2: fix a few "return err" instead of "goto unlock" in mv88e6xxx.c ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
No driver implements port_fdb_getnext anymore, and port_fdb_dump is preferred anyway, so remove this function from DSA. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Now that port_fdb_dump is implemented and even simpler, get rid of port_fdb_getnext. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Implement the port_fdb_dump DSA operation. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
There is no need to write the MAC address before every Get Next operation, since ATU MAC registers are not cleared between calls. Move the _mv88e6xxx_atu_mac_write call outside of _mv88e6xxx_atu_getnext so future code could call ATU Get Next multiple times and save a few register access. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
There is no need to write the VLAN ID before every Get Next operation, since the VTU VID register is not cleared between calls. Move the VID write call in a _mv88e6xxx_vtu_vid_write function outside of _mv88e6xxx_vtu_getnext so future code could call VTU Get Next multiple times and save a few register accesses. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Not all switch chips support a Get Next operation to iterate on its FDB. So add a more simple port_fdb_dump function for them. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'mac80211-next-for-davem-2015-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Here's another set of patches for the current cycle: * I merged net-next back to avoid a conflict with the * cfg80211 scheduled scan API extensions * preparations for better scan result timestamping * regulatory cleanups * mac80211 statistics cleanups * a few other small cleanups and fixes ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 yankejian 提交于
the global Soc configuration is treated by syscon, and sub ctrl bus is Soc bus. it has to be treated by syscon. Signed-off-by: Nyankejian <yankejian@huawei.com> Signed-off-by: Nlisheng <lisheng011@huawei.com> Signed-off-by: Nlipeng <lipeng321@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-