Add hwmod support for IP's that are present in AM43x, but not in AM335x.
AM43x additional ones added here are,
1. synctimer
2. timer8-11
3. ehrpwm3-5
4. spi2-4
5. gpio4-5

AM43x pruss interconnect which is different as compared to AM335x, has
been taken care.

And register offsets for same hwmod's shared with AM335x is different,
AM43x register offsets are updated appropriately.

ocp clock of those in l4_wkup is fed from "sys_clkin_ck" instead of
"dpll_core_m4_div2_ck", so "ocpif" for those in AM43x l4_wkup has been
added seperately.

hwmod's has been added for those that have main clock (wkup_m3, control,
gpio0) and clock domain (l4_hs) different from AM335x. debugss and
adc_tsc that have different clocks and clockdomains repectively has not
been added due to the reasons mentioned below.

AM43x also has IP's like qspi, hdq1w, vpfe, des, rng, usb, dss, debugss,
adc_tsc. These are not handled here due to both/either of following
reasons,
1. To avoid churn; most of them don't have DT bindings, which would
   necessitate adding address space in hwmod, which any way would have
   to be removed once DT bindings happen with driver support.
2. patches would come in from sources other than the author
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Acked-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Adding the hwmod data for DRA7XX platforms.
Signed-off-by: NAmbresh K <ambresh@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Address space is being removed from hwmod database and DT information
in <reg> property is being used. Currently the 0th index of device
address space is used to map for register target address. This is not
always true, eg. cpgmac has it's sysconfig in second address space.

Handle it by specifying index of device address space to be used for
register target. As default value of this field would be zero with
static initialization, existing behaviour of using first address space
for register target while using DT would be kept as such.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Tested-by: NMugunthan V N <mugunthanvnm@ti.com>
[paul@pwsan.com: use u8 rather than int to save memory]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

With commit '82702ea1' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.

This was rootcaused to hwmod trying to reset console uart while
earlycon was using it.  The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.

Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.

This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reported-by: NMark Jackson <mpfj-list@newflow.co.uk>
Reported-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: NMark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Adding the hwmod data for OMAP54xx SOCs.

Additional changes done on top of initial SOC data files.
- The IO resource information like dma request lines, irq number and
ocp address space can be populated via dt blob. So such data is stripped
from OMAP5 SOC hwmod data file.

- SDMA IO resource information is still kept since dmaengine work
is till ongoing. Once the legacy dma platform driver becomes obsolete,
SDMA io space information can be removed.

- The devices like dss, aess, usb which are missing the device tree bindings,
hwmod data is not added since OMAP5 is DT only build. When such devices add
the dt bindings, respective hwmod data can be added along with it.

With above update, we now need about ~2000 loc vs ~6000 loc with previous
version of the patch for OMAP5 hwmod data file. Ofcourse with addition of
few more drivers it can go upto ~2400 loc which is still better than the
earlier version.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

With the OMAP serial driver sysc cleanup patches in this series, we can
now remove the hwmod external apis for sysc fiddling.

While at this, also remove unused sysc auto idle api from hwmod code.
Tested-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NRajendra nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>  # OMAP4/Panda
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Some IPs (like UART) need the sidle mode to be controlled in SW only
while they are active. Once they go inactive, they need the IP to be
put back in HW control so they are also wakeup capable.

The flag HWMOD_SWSUP_SIDLE takes care of IPs which need the sidle
mode to be *always* controlled in SWSUP. We now have a need to control
IPs sidle mode in SWSUP only while its active.

So define a new flag 'HWMOD_SWSUP_SIDLE_ACT' to help the framework
know about these new IP requirements.
Tested-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>  # OMAP4/Panda
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod
framework. Just get rid of it, so we have one less flag to
worry about.
Tested-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

For some unknown reason, allowing hwmod to control MIDLEMODE causes
core_pwrdm to not hit idle states for musb in DM3730 at least.
I've verified that setting any MIDLEMODE value other than "force
standby" before enabling the device causes subsequent suspend
attempts to fail with core_pwrdm not entering idle states, even
if the driver is unloaded and "force standby" is restored before
suspend attempt. To recover from this, soft reset can be used, but
that's not suitable solution for suspend.

Keeping the register set at force standby (reset value) makes it work
and device still functions properly, as musb has driver-controlled
OTG_FORCESTDBY register that controls MSTANDBY signal.
Note that TI PSP kernels also have similar workarounds.

This patch also fixes HWMOD_SWSUP_MSTANDBY documentation to match the
actual flag name.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Enable the AESS auto-gating control bit during AESS hwmod setup.  This
fixes the following boot warning on OMAP4:

omap_hwmod: aess: _wait_target_disable failed

Without this patch, the AESS IP block does not indicate to the PRCM
that it is idle after it is reset.  This prevents some types of SoC
power management until something sets the auto-gating control bit.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

After setup/enable, some IP blocks need some additional setting to
indicate the PRCM that they are inactive until they are configured.
Some examples on OMAP4 include the AESS and FSUSB IP blocks.

To fix this cleanly, this patch adds another optional function
pointer, enable_preprogram, to the IP block's hwmod data.  The function
that is pointed to is called by the hwmod code immediately after the
IP block is reset.

This version of the patch includes a patch description fix from Felipe.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Felipe Balbi <balbi@ti.com>

Apparently, on some OMAPs, the MPU can't be allowed to enter WFI while
certain peripherals are active.  It's not clear why, and it's likely
that there is simply some other bug in the driver or integration code.
But since the likelihood that anyone will have the time to track these
problems down in the future seems quite small, we'll provide a
flag, HWMOD_BLOCK_WFI, to mark these issues in the hwmod data.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Apparently, on some OMAPs, the MPU can't be allowed to enter WFI while
certain peripherals are active.  It's not clear why, and it's likely
that there is simply some other bug in the driver or integration code.
But since the likelihood that anyone will have the time to track these
problems down in the future seems quite small, we'll provide a
flag, HWMOD_BLOCK_WFI, to mark these issues in the hwmod data.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add flags parameter for omap_hwmod_count_resources() so users can tell which
type of resources they are interested when counting them in hwmod database.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NBenoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

OMAP4 has module specific context lost registers which makes it now
possible to have module level context loss count, instead of relying
on the powerdomain level context count.

Add 2 private hwmod api's to update/clear the hwmod/module specific
context lost counters/register.

Update the module specific context_lost_counter and clear the hardware
bits just after enabling the module.

omap_hwmod_get_context_loss_count() now returns the hwmod context loss
count them on platforms where they exist (OMAP4), else fall back on
the pwrdm level counters for older platforms.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added function kerneldoc, fixed structure kerneldoc,
 rearranged structure to avoid memory waste, marked fns as OMAP4-specific,
 prevent fn entry on non-OMAP4 chips, reduced indentation, merged update
 and clear, merged patches]
[t-kristo@ti.com: added support for arch specific hwmod ops, and changed
 the no context offset indicator to USHRT_MAX]
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: use NO_CONTEXT_LOSS_BIT flag rather than USHRT_MAX;
 convert unsigned context lost counter to int to match the return type;
 get rid of hwmod_ops in favor of the existing soc_ops mechanism;
 move context loss low-level accesses to the PRM code]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.

Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.

This is needed for the ARM common zImage support.

[tony@atomide.com: updated to not print a warning]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Let's make omap_hwmod local to mach-omap2 for
ARM common zImage support.
Signed-off-by: NTony Lindgren <tony@atomide.com>

On OMAP4 most modules/hwmods support module level context status. On
OMAP3 and earlier, we relied on the power domain level context status.
Identify all modules that don't support 'context_offs' by adding a
flag bit, HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT.  Rest have a valid
'context_offs' populated in .prcm structure already.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: add flag bit rather than overloading .context_offs;
 update changelog message]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Currently hwmod only provides the offset for the context lose
register, and if we attempt to share the same register between two or
more hwmods, the resulting context loss counts get wrong. Thus, we
need a way to specify which bits are used for the context loss
information for each.  This is accomplished by adding a new field to
the omap4 prcm struct, 'lostcontext_mask', which specifies a bit-mask
to use for filtering the register.

Mark the affected hwmods appropriately.  'l4_abe' hwmod uses the
LOSTMEM_AESSMEM bit of RM_ABE_AESS_CONTEXT register, as l4_abe doesn't
have its own dedicated register for this purpose. This register is
shared with 'aess' hwmod, thus both hwmods must also specify which
bits of the register are used for them.

This patch only adds the hwmod data, but a future patch should add
code support such that only the specified bits are read and cleared by
the context lose counter update code. If a hwmod doesn't specify
'lostcontext_mask' (default behavior), the whole contents of the
context register should be used without any filtering.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply after conversion to use flag bit for
 missing module context-loss register; combined data and code patches;
 dropped code change due to serial driver breakage]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Several hwmod function prototypes appear to not have an implementation
because the corresponding functions were removed or renamed.
Those prototypes are unneeded anymore - remove them.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
[paul@pwsan.com: tweaked subject]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This patch adds HWMOD data for all the peripherals of
AM335X device and also hooks up to the existing OMAP framework.

hwmod data has been already been cleaned up for the recent
changes in clocktree, where all leaf nodes have been removed,
since with modulemode based control, both clock and hwmod
interface does same thing. This reduces the code size to large
extent and also avoids duplication of same control.
So instead of specifying module's leaf node as a main_clk,
now we are relying on parent clock of module's functional clock.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: removed period in hwmod device names; changed mmc2 main_clk
 to mmc_clk at Vaibhav's request; added trailing commas to structure
 records at Tony's request to deal with some rmk parsing issues; added
 OMAP_INTC_START to facilitate sparse-IRQ conversion]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

With the new devices (like, AM33XX and OMAP5) we now only support
DT boot mode of operation and now it is the time to start killing
slowly the dependency on hwmod, so with this patch, we are starting
with device resources.
The idea here is implemented considering to both boot modes -
  - DT boot mode
    OF framework will construct the resource structure (currently
    does for MEM & IRQ resource) and we should respect/use these
    resources, killing hwmod dependency.
    If pdev->num_resources > 0, we assume that MEM & IRQ resources
    have been allocated by OF layer already (through DTB).

    Once DMA resource is available from OF layer, we should
    kill filling any resources from hwmod.

  - Non-DT boot mode
    Here, pdev->num_resources = 0, and we should get all the
    resources from hwmod (following existing steps)
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
[b-cousson@ti.com: Fix some checkpatch CHECK issues]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Commit ac5b0ea3 (Merge tag 'omap-devel-f-for-3.6'...) had a merge
conflict that somehow got incorrecly resolved in a lossy way for
commit bed9d1bb (ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API).
Fix the issue by applying the missing pieces.
Reported-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.

In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).

During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)

DMADISABLE bit is present in usbotgss module of omap5.

Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add an API to get main clock name associated with a given @oh.
This will avoid the need to construct fclk names during early
initialization in order to get fclk handle using clk_get().
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In case of AM33XX device, XXX_RSTST register offset is not
consistent across PRM modules/instances,

PRM_XXX            RSTST
=========================
PRM_PER_MOD:       0x04
PRM_WKUP_MOD:      0x0C
PRM_MPU_MOD:       NA
PRM_DEVICE_MOD:    0x08

This means, we need to pass on XXX_RSTST register offset
information through omap_hwmod data, similar to XXX_RSTCTRL.

Currently, this field is only applicable and used for AM33XX
devices.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,

sysc_type3:
|  3     2  |  1    0  |
| STDBYMODE | IDLEMODE |

So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM.  Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.

NOTE: the cpu_is* check for _enable_module was different than
      the one for _disable_module, and this patch uses
      cpu_is_omap44xx() for both.
Signed-off-by: NKevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
 per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the SL2 interface IP block and interconnect data.  The SL2 is related
to the IVA-HD subsystem.

Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect.  This can provide a direct system interconnect link to
other devices stacked on the OMAP package.

Add the ELM IP block and interconnect data.  The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>

Now that the data has been converted to use interface registration, we
can remove the (now unused) direct hwmod registration code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Add support for direct IP block interconnect ("link") registration to
the hwmod code via a new function, omap_hwmod_register_links().  This
will replace direct registration of hwmods, and a subsequent patch
will remove omap_hwmod_register().

This change will allow a subsequent patch to remove the hwmod data
link arrays.  This will reduce the size of the hwmod static data and
also make it easier to generate the data files.  It will also make it
possible to share some of the struct omap_hwmod records across
multiple SoCs, since the link array pointers will be removed from the
struct omap_hwmod.

The downside is that boot time will increase.  Minimizing boot time
was the reason why the link arrays were originally introduced.
Removing them will require extra computation during boot to allocate
memory and associate IP blocks with their interconnects.  However,
since the current kernel development focus is on reducing the number
of lines in arch/arm/mach-omap2/, boot time impact is now seemingly
considered a lower priority.

This patch contains additional complexity to reduce the number of
memory allocations required for this change.  This reduces the boot
time impact: total hwmod link registration time was ~ 2655
microseconds with a simple allocation strategy, but is now ~ 549
microseconds[1] with the approach taken by this patch.

1. Measured on a BeagleBoard 35xx @ 500MHz MPU/333 MHz CORE, average
   of 7 samples.  Total uncertainty is +/- 61 microseconds.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Extend the OCP_* register offsets in the struct
omap_hwmod_class_sysconfig to 32 bits.  This is required to add the
OMAP4+ GPU hwmod, which uses OCP_* register offsets larger than 16
bits.

Another possible solution may be to simply add a single 16 bit offset
field in this structure, and to add code to factor that offset into
all OCP_* register accesses.  This would save some memory, since
almost no modules need 32 bit offsets.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set.  This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

The timer integration code pokes around in hwmod data structures.
Those data structures are about to change.  Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.

The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions.  This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.

Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.

In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.

Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NFernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
 yet upstream; the FDIF change will need to be added later once the FDIF
 data is merged]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In the SYSC_TYPE1_XXX_MASK configuration, SYSC_XXX_SHIFT macro
is used which is not defined anywhere in the kernel.
Until now the build was going through successfully, since it
is not being used anywhere in kernel.

This bug got introduced by the commit
358f0e63 ("OMAP3: hwmod: support
to specify the offset position of various SYSCONFIG register bits.")
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.

Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NShweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.

Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().

A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: NKevin Hilman <khilman@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
 edited some documentation]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
 changes; added kerneldoc]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.

[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
 improved function documentation; modified to iterate only through dynamic
 pads; modified to skip pads where idle mode doesn't enable wakeups; split
 patches]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>