Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And use CONFIG_SPARC instead of CONFIG_SPARC64 as the
test.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver will crash when the chip has been initialized by EFI before
tg3_init_one().  In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.

The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 3.75.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On most tg3 chips, the memory enable bit in the PCI command register
gets cleared during chip reset and must be restored before accessing
PCI registers using memory cycles.  The chip does not generate
interrupt during chip reset, but the irq handler can still be called
because of irq sharing or irqpoll.  Reading a register in the irq
handler can cause a master abort in this scenario and may result in a
crash on some architectures.

Use the TG3_FLAG_CHIP_RESETTING flag to tell the irq handler to exit
without touching any registers.  The checking of the flag is in the
"slow" path of the irq handler and will not affect normal performance.
The msi handler is not shared and therefore does not require checking
the flag.

Thanks to Bernhard Walle <bwalle@suse.de> for reporting the problem.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This flag to support multiple PCIX split completions was never used
because of hardware bugs.  This will make room for a new flag.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.

I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: NDan Aloni <da-x@monatomic.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1.  Add race condition check after netif_stop_queue().  tg3_tx() runs
    without netif_tx_lock and can race with tg3_start_xmit_dma_bug() ->
    tg3_tso_bug().

2.  Firmware TSO in 5703/5704/5705 also have the same TSO limitation,
    i.e. they cannot handle TSO headers bigger than 80 bytes.  Rename
    TG3_FL2_HW_TSO_1_BUG to TG3_FL2_TSO_BUG and set this flag on
    these chips as well.

3.  Update version to 3.74.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 3.73.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print the most useful information during tx timeout to help debug.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set DMA read watermark to 4 on 5703 in PCIX mode.  This is needed to
prevent some tx timeouts.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the following problem:

http://bugzilla.kernel.org/show_bug.cgi?id=7969

The MSI state needs to be saved during suspend.  PCI state saved
during tg3_init_one() does not contain valid MSI state because
MSI hasn't been enabled.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During an oprofile session of linux-2.6.20 on a dual opteron system, I noticed
an expensive divide was done in tg3_poll().

I am using gcc-4.1.1, so the following comment from drivers/net/tg3.c seems
over-optimistic :

/* Do not place this n-ring entries value into the tp struct itself,
  * we really want to expose these constants to GCC so that modulo et
  * al.  operations are done with shifts and masks instead of with
  * hw multiply/modulo instructions.  Another solution would be to
  * replace things like '% foo' with '& (foo - 1)'.
  */
#define TG3_RX_RCB_RING_SIZE(tp)        \
         ((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) ?  512 : 1024)

Assembly code before patch :
(oprofile results included)
   6434  0.0088 :ffffffff803684b9:       mov    0x6f0(%r15),%eax
    587 8.0e-04 :ffffffff803684c0:       and    $0x40000,%eax
   2170  0.0030 :ffffffff803684c5:       cmp    $0x1,%eax
                :ffffffff803684c8:       lea    0x1(%r13),%eax
                :ffffffff803684cc:       sbb    %ecx,%ecx
   2051  0.0028 :ffffffff803684ce:       xor    %edx,%edx
                :ffffffff803684d0:       and    $0x200,%ecx
     20 2.7e-05 :ffffffff803684d6:       add    $0x200,%ecx
   1986  0.0027 :ffffffff803684dc:       div    %ecx
103427  0.1410 :ffffffff803684de:       cmp    %edx,0xffffffffffffff7c(%rbp)

Assembly code after the suggested patch :

ffffffff803684b9:           mov    0x6f0(%r15),%eax
ffffffff803684c0:           and    $0x40000,%eax
ffffffff803684c5:           cmp    $0x1,%eax
ffffffff803684c8:           sbb    %eax,%eax
ffffffff803684ca:           inc    %r13d
ffffffff803684cd:           and    $0x200,%eax
ffffffff803684d2:           add    $0x1ff,%eax
ffffffff803684d7:           and    %eax,%r13d
ffffffff803684da:           cmp    %r13d,0xffffffffffffff7c(%rbp)
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the NETIF_F_TSO #ifdef-ery in drivers/net; this was
for old-old-2.4 compat (even current 2.4 has NETIF_F_TSO)
but it's time to get rid of it by now.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some PHY trim values need to be fine-tuned on 5755M to be
IEEE-compliant.

Update version to 3.72.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 3.71.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5906 PHY requires a special register bit to power down and up the
PHY.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hot-plug scripts can call tg3_open() as soon as register_netdev() is
called in tg3_init_one().  We need to call pci_set_drvdata() before
register_netdev(), and netif_carrier_off() needs to be moved to
tg3_open() to avoid race conditions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tp->link_config.orig_* values must be assigned during
tg3_set_settings() because these values will be used to setup the
link speed during tg3_open().  Without these assignments, the link
speed settings will be all messed by if tg3_set_settings() is called
when the device is down.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace kmalloc+memset with kzalloc
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the message to more clearly identify Serdes devices.

Update version to 3.70.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change some udelay() in some eeprom functions to msleep().  Eeprom
related functions are always called from sleepable context.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use netif_msg_* to turn on or off some messages.

Based on Stephen Hemminger's initial patch.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Honor the advertisement bitmask from ethtool.  We used to always
advertise the full capability when autoneg was set to on.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Tg3_FLG2_IS_NIC flag to unambiguously determine whether the
device is NIC or onboard.  Previously, the EEPROM_WRITE_PROT flag was
overloaded to also mean onboard.  With the separation, we can
support some devices that are onboard but do not use eeprom write
protect.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Phy loopback on most 10/100 devices need to be run in 1Gbps mode in
GMII mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix up for make allyesconfig.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>

Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: NIra W. Snyder <kernel@irasnyder.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to hardware errata, TSO must be disabled if the PCI Express clock
request is enabled on 5906.  The chip may hang when transmitting TSO
frames if CLKREQ is enabled.

Update version to 3.69.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer 5906 bootcode needs about 7ms to finish resetting so the poll
firmware loop was changed to maximum 20ms.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proper upper limits for the loops and check for all error
conditions.

The problem was noticed by Adrian Bunk.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a bug reported in:

http://bugzilla.kernel.org/show_bug.cgi?id=7438

tg3_close() turns off the PHY if WoL and ASF are both disabled.  On
the next tg3_open(), some devices such as the 5752M will not be
brought up correctly without a PHY reset early in the reset sequence.
The PHY clock is needed for some internal MAC blocks to function
correctly.

This problem is fixed by always resetting the PHY early in
tg3_reset_hw() when it is called from tg3_open() or tg3_resume().
tg3_setup_phy() can then be called later in the sequence without the
reset_phy parameter set to 1, since the PHY reset is already done.

Update version to 3.68.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The minimum tx ring size must be greater than MAX_SKB_FRAGS or 3
times that on some chips with TSO bugs.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>