Meta has instructions for accessing:
 - bytes        - GETB (1 byte)
 - words        - GETW (2 bytes)
 - doublewords  - GETD (4 bytes)
 - longwords    - GETL (8 bytes)

All accesses must be aligned. Unaligned accesses can be detected and
made to fault on Meta2, however it isn't possible to fix up unaligned
writes so we don't bother fixing up reads either.

This patch adds metag memory handling code including:
 - I/O memory (io.h, ioremap.c): Actually any virtual memory can be
   accessed with these helpers. A part of the non-MMUable address space
   is used for memory mapped I/O. The ioremap() function is implemented
   one to one for non-MMUable addresses.
 - User memory (uaccess.h, usercopy.c): User memory is directly
   accessible from privileged code.
 - Kernel memory (maccess.c): probe_kernel_write() needs to be
   overwridden to use the I/O functions when doing a simple aligned
   write to non-writecombined memory, otherwise the write may be split
   by the generic version.

Note that due to the fact that a portion of the virtual address space is
non-MMUable, and therefore always maps directly to the physical address
space, metag specific I/O functions are made available (metag_in32,
metag_out32 etc). These cast the address argument to a pointer so that
they can be used with raw physical addresses. These accessors are only
to be used for accessing fixed core Meta architecture registers in the
non-MMU region, and not for any SoC/peripheral registers.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add memory management files for metag.

Meta's 32bit virtual address space is split into two halves:
 - local (0x08000000-0x7fffffff): traditionally local to a hardware
   thread and incoherent between hardware threads. Each hardware thread
   has it's own local MMU table. On Meta2 the local space can be
   globally coherent (GCOn) if the cache partitions coincide.
 - global (0x88000000-0xffff0000): coherent and traditionally global
   between hardware threads. On Meta2, each hardware thread has it's own
   global MMU table.

The low 128MiB of each half is non-MMUable and maps directly to the
physical address space:
 - 0x00010000-0x07ffffff: contains Meta core registers and maps SoC bus
 - 0x80000000-0x87ffffff: contains low latency global core memories

Linux usually further splits the local virtual address space like this:
 - 0x08000000-0x3fffffff: user mappings
 - 0x40000000-0x7fffffff: kernel mappings
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add cache and TLB handling code for metag, including the required
callbacks used by MM switches and DMA operations. Caches can be
partitioned between the hardware threads and the global space, however
this is usually configured by the bootloader so Linux doesn't make any
changes to this configuration. TLBs aren't configurable, so only need
consideration to flush them.

On Meta1 the L1 cache was VIVT which required a full flush on MM switch.
Meta2 has a VIPT L1 cache so it doesn't require the full flush on MM
switch. Meta2 can also have a writeback L2 with hardware prefetch which
requires some special handling. Support is optional, and the L2 can be
detected and initialised by Linux.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add source files from the Thread Binary Interface (TBI) library which
provides useful low level operations and traps/context management.

Among other things it handles interrupt/exception/syscall entry (in
tbipcx.S).
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add the main header for the Thread Binary Interface (TBI) library which
provides useful low level operations and trap/context management.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add boot code for metag. Due to the multi-threaded nature of Meta it is
not uncommon for an RTOS or bare metal application to be started on
other hardware threads by the bootloader. Since there is a single MMU
switch which affects all threads, the MMU is traditionally configured by
the bootloader prior to starting Linux. The bootloader passes a
structure to Linux which among other things contains information about
memory regions which have been mapped. Linux then assumes control of the
local heap memory region.

A kernel arguments string pointer or a flattened device tree pointer can
be provided in the third argument.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add the header <asm/metag_mem.h> describing addresses, fields, and bits
of various core memory mapped registers in the low non-MMU region.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add a couple of header files containing core architecture constants.

The first (<asm/metag_isa.h>) contains some constants relating to the
instruction set, such as values to give to the CACHEW and CACHER
instructions.

The second (<asm/metag_regs.h>) contains constants for the core register
units directly accessible to various instructions, and for the
registers, fields, and bits in those units. The main units described are
the control unit (CT.*), the trigger unit (TR.*), and the run-time trace
unit (TT.*).
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>

Add MAINTAINERS entry for the metag architecture port.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>

Some 32 bit architectures require 64 bit values to be aligned (for
example Meta which has 64 bit read/write instructions). These require 8
byte alignment of event data too, so use
!CONFIG_HAVE_64BIT_ALIGNED_ACCESS instead of !CONFIG_64BIT ||
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to decide alignment, and align
buffer_data_page::data accordingly.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org> (previous version subtly different)

On 64 bit architectures with no efficient unaligned access, padding and
explicit alignment must be added in various places to prevent unaligned
64bit accesses (such as taskstats and trace ring buffer).

However this also needs to apply to 32 bit architectures with 64 bit
accesses requiring alignment such as metag.

This is solved by adding a new Kconfig symbol HAVE_64BIT_ALIGNED_ACCESS
which defaults to 64BIT && !HAVE_EFFICIENT_UNALIGNED_ACCESS, and can be
explicitly selected by METAG and any other relevant architectures. This
can be used in various places to determine whether 64bit alignment is
required.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Will Drewry <wad@chromium.org>

The commit "binfmt_elf: cleanups"
(f670d0ec) removed an ifndef elf_map but
this breaks compilation for metag which does define elf_map.

This adds the ifndef back in as it was before, but does not affect the
other cleanups made by that patch.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Acked-by: NMikael Pettersson <mikpe@it.uu.se>

Some architectures have symbol prefixes and set CONFIG_SYMBOL_PREFIX,
but this wasn't taken into account by the generic cond_syscall. It's
easy enough to fix in a generic fashion, so add the symbol prefix to
symbol names in cond_syscall when CONFIG_SYMBOL_PREFIX is set.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Make asm-generic/io.h check CONFIG_VIRT_TO_BUS before defining
virt_to_bus() and bus_to_virt(), otherwise it's easy to accidentally
have a silently failing incorrect direct mapped definition rather then
no definition at all.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Pull input subsystem fixes from Dmitry Torokhov:
 "Two small driver fixups and a documentation update for managed input
  devices"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - fix wacom_set_report retry logic
  Input: document that unregistering managed devices is not necessary
  Input: lm8323 - fix checking PWM interrupt status

Commit c060f943 ("mm: use aligned zone start for pfn_to_bitidx
calculation") fixed out calculation of the index into the pageblock
bitmap when a !SPARSEMEM zome was not aligned to pageblock_nr_pages.

However, the _allocation_ of that bitmap had never taken this alignment
requirement into accout, so depending on the exact size and alignment of
the zone, the use of that index could then access past the allocation,
resulting in some very subtle memory corruption.

This was reported (and bisected) by Ingo Molnar: one of his random
config builds would hang with certain very specific kernel command line
options.

In the meantime, commit c060f943 has been marked for stable, so this
fix needs to be back-ported to the stable kernels that backported the
commit to use the right alignment.
Bisected-and-tested-by: NIngo Molnar <mingo@kernel.org>
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull xen fixes from Konrad Rzeszutek Wilk:
 "Two fixes:

   - A simple bug-fix for redundant NULL check.

   - CVE-2013-0228/XSA-42: x86/xen: don't assume %ds is usable in
     xen_iret for 32-bit PVOPS

  and two reverts:

   - Revert the PVonHVM kexec.  The patch introduces a regression with
     older hypervisor stacks, such as Xen 4.1."

* tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  Revert "xen PVonHVM: use E820_Reserved area for shared_info"
  Revert "xen/PVonHVM: fix compile warning in init_hvm_pv_info"
  xen: remove redundant NULL check before unregister_and_remove_pcpu().
  x86/xen: don't assume %ds is usable in xen_iret for 32-bit PVOPS.

As reported by Klaus Schmidinger:
 "In VDR I use an ioctl() call with FE_READ_UNCORRECTED_BLOCKS on a
  device (using stb0899).  After this call I check 'errno' for
  EOPNOTSUPP to determine whether this device supports this call.  This
  used to work just fine, until a few months ago I noticed that my
  devices using stb0899 didn't display their signal quality in VDR's OSD
  any more.  After further investigation I found that
  ioctl(FE_READ_UNCORRECTED_BLOCKS) no longer returns EOPNOTSUPP, but
  rather ENOTTY.  And since I stop getting the signal quality in case
  any unknown errno value appears, this broke my signal quality query
  function."

While the changes reflect what is there at:

  http://comments.gmane.org/gmane.linux.kernel/1235728

it does cause regression on userspace.  So, revert it to stop the
damage.

This reverts commit 177ffe50 ("[media] dvb_frontend: return -ENOTTY
for unimplement IOCTL").
Reported-by: NKlaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull sparc fixes from David Miller:
 "A couple small fixes for sparc including some THP brown-paper-bag
  material:

   1) During the merging of all the THP support for various
      architectures, sparc missed adding a
      HAVE_ARCH_TRANSPARENT_HUGEPAGE to it's Kconfig, oops.

   2) Sparc needs to be mindful of hugepages in get_user_pages_fast().

   3) Fix memory leak in SBUS probe, from Cong Ding.

   4) The sunvdc virtual disk client driver has a test of the bitmask of
      vdisk server supported operations which was off by one bit"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sunvdc: Fix off-by-one in generic_request().
  sparc64: Fix get_user_pages_fast() wrt. THP.
  sparc64: Add missing HAVE_ARCH_TRANSPARENT_HUGEPAGE.
  sparc: kernel/sbus.c: fix memory leakage

Pull one more x86 fix from Peter Anvin:
 "Sigh.  One more patch in the "please don't brick my Samsung" series"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: Clear EFI_RUNTIME_SERVICES rather than EFI_BOOT by "noefi" boot parameter

Pull PCI fix from Bjorn Helgaas:
 "This is another fix for v3.8.  It fixes an oops that happens when a
  Thunderbolt adapter is unplugged (remove device, poll for PME events
  on no-longer-existing device, oops)."

* tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/PM: Clean up PME state when removing a device

Pull omapdss fixes from Tomi Valkeinen:
 "It'd be great if these two late fixes would still make it into 3.8.
  The other one fixes ARM kernel compilation when using 'allyesconfig',
  and the other makes DPI displays function again on OMAP3630 boards:

   - Fix ARM compilation with "allyesconfig" (omapdrm: fix the
     dependency to omapdss)

   - fix DPI displays on OMAP3630 (OMAPDSS: add FEAT_DPI_USES_VDDS_DSI
     to omap3630_dss_feat_list)"

* tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux:
  omapdrm: fix the dependency to omapdss
  OMAPDSS: add FEAT_DPI_USES_VDDS_DSI to omap3630_dss_feat_list

Pull i2c maintainer info update from Wolfram Sang:
 "Since my old email and repos are not working anymore, and this already
  caused some confusion, I think a MAINTAINERS update for 3.8 is
  helpful.  So, people trying I2C with the new kernel can properly reach
  me and find my repos."

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: change my email and repos

This reverts commit 9d02b43d.

We are doing this b/c on 32-bit PVonHVM with older hypervisors
(Xen 4.1) it ends up bothing up the start_info. This is bad b/c
we use it for the time keeping, and the timekeeping code loops
forever - as the version field never changes. Olaf says to
revert it, so lets do that.
Acked-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

This reverts commit a7be94ac.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The 'operations' bitmap corresponds one-for-one with the operation
codes, no adjustment is necessary.
Reported-by: NMark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

omapdrm uses "select" in Kconfig to enable omapdss. This doesn't work
correctly, as "select" forces omapdss to be enabled in the config even
if it normally could not be enabled because of missing Kconfig
dependencies.

This causes a build break on ARM, when using allyesconfig:

drivers/video/omap2/dss/dss.c: In function 'dss_calc_clock_div':
drivers/video/omap2/dss/dss.c:572:20: error: 'CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK' undeclared (first use in this function)
drivers/video/omap2/dss/dss.c:572:20: note: each undeclared identifier is reported only once for each function it appears in

Instead of using select, this patch changes omapdrm to use "depend
on".
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

commit 195e672a
   OMAPDSS: DPI: Remove cpu_is_xxxx checks

made the mistake of assuming that cpu_is_omap34xx() is exclusive of
other cpu_is_* predicates whereas it includes cpu_is_omap3630().

So on an omap3630, code that was previously enabled by
  if (cpu_is_omap34xx())
is now disabled as
  dss_has_feature(FEAT_DPI_USES_VDDS_DSI)
fails.

So add FEAT_DPI_USES_VDDS_DSI to omap3630_dss_feat_list.

Cc: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There was a serious problem in samsung-laptop that its platform driver is
designed to run under BIOS and running under EFI can cause the machine to
become bricked or can cause Machine Check Exceptions.

    Discussion about this problem:
    https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
    https://bugzilla.kernel.org/show_bug.cgi?id=47121

    The patches to fix this problem:
    efi: Make 'efi_enabled' a function to query EFI facilities
    83e68189

    samsung-laptop: Disable on EFI hardware
    e0094244

Unfortunately this problem comes back again if users specify "noefi" option.
This parameter clears EFI_BOOT and that driver continues to run even if running
under EFI. Refer to the document, this parameter should clear
EFI_RUNTIME_SERVICES instead.

Documentation/kernel-parameters.txt:
===============================================================================
...
	noefi		[X86] Disable EFI runtime services support.
...
===============================================================================

Documentation/x86/x86_64/uefi.txt:
===============================================================================
...
- If some or all EFI runtime services don't work, you can try following
  kernel command line parameters to turn off some or all EFI runtime
  services.
	noefi		turn off all EFI runtime services
...
===============================================================================
Signed-off-by: NSatoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/511C2C04.2070108@jp.fujitsu.com
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

unregister_and_remove_pcpu on a NULL pointer is a no-op, so the NULL check in
sync_pcpu can be removed.
Signed-off-by: NCyril Roelandt <tipecaml@gmail.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

This fixes CVE-2013-0228 / XSA-42

Drew Jones while working on CVE-2013-0190 found that that unprivileged guest user
in 32bit PV guest can use to crash the > guest with the panic like this:

-------------
general protection fault: 0000 [#1] SMP
last sysfs file: /sys/devices/vbd-51712/block/xvda/dev
Modules linked in: sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4
iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6
xt_state nf_conntrack ip6table_filter ip6_tables ipv6 xen_netfront ext4
mbcache jbd2 xen_blkfront dm_mirror dm_region_hash dm_log dm_mod [last
unloaded: scsi_wait_scan]

Pid: 1250, comm: r Not tainted 2.6.32-356.el6.i686 #1
EIP: 0061:[<c0407462>] EFLAGS: 00010086 CPU: 0
EIP is at xen_iret+0x12/0x2b
EAX: eb8d0000 EBX: 00000001 ECX: 08049860 EDX: 00000010
ESI: 00000000 EDI: 003d0f00 EBP: b77f8388 ESP: eb8d1fe0
 DS: 0000 ES: 007b FS: 0000 GS: 00e0 SS: 0069
Process r (pid: 1250, ti=eb8d0000 task=c2953550 task.ti=eb8d0000)
Stack:
 00000000 0027f416 00000073 00000206 b77f8364 0000007b 00000000 00000000
Call Trace:
Code: c3 8b 44 24 18 81 4c 24 38 00 02 00 00 8d 64 24 30 e9 03 00 00 00
8d 76 00 f7 44 24 08 00 00 02 80 75 33 50 b8 00 e0 ff ff 21 e0 <8b> 40
10 8b 04 85 a0 f6 ab c0 8b 80 0c b0 b3 c0 f6 44 24 0d 02
EIP: [<c0407462>] xen_iret+0x12/0x2b SS:ESP 0069:eb8d1fe0
general protection fault: 0000 [#2]
---[ end trace ab0d29a492dcd330 ]---
Kernel panic - not syncing: Fatal exception
Pid: 1250, comm: r Tainted: G      D    ---------------
2.6.32-356.el6.i686 #1
Call Trace:
 [<c08476df>] ? panic+0x6e/0x122
 [<c084b63c>] ? oops_end+0xbc/0xd0
 [<c084b260>] ? do_general_protection+0x0/0x210
 [<c084a9b7>] ? error_code+0x73/
-------------

Petr says: "
 I've analysed the bug and I think that xen_iret() cannot cope with
 mangled DS, in this case zeroed out (null selector/descriptor) by either
 xen_failsafe_callback() or RESTORE_REGS because the corresponding LDT
 entry was invalidated by the reproducer. "

Jan took a look at the preliminary patch and came up a fix that solves
this problem:

"This code gets called after all registers other than those handled by
IRET got already restored, hence a null selector in %ds or a non-null
one that got loaded from a code or read-only data descriptor would
cause a kernel mode fault (with the potential of crashing the kernel
as a whole, if panic_on_oops is set)."

The way to fix this is to realize that the we can only relay on the
registers that IRET restores. The two that are guaranteed are the
%cs and %ss as they are always fixed GDT selectors. Also they are
inaccessible from user mode - so they cannot be altered. This is
the approach taken in this patch.

Another alternative option suggested by Jan would be to relay on
the subtle realization that using the %ebp or %esp relative references uses
the %ss segment.  In which case we could switch from using %eax to %ebp and
would not need the %ss over-rides. That would also require one extra
instruction to compensate for the one place where the register is used
as scaled index. However Andrew pointed out that is too subtle and if
further work was to be done in this code-path it could escape folks attention
and lead to accidents.
Reviewed-by: NPetr Matousek <pmatouse@redhat.com>
Reported-by: NPetr Matousek <pmatouse@redhat.com>
Reviewed-by: NAndrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Mostly mirrors the s390 logic, as unlike x86 we don't need the
SetPageReferenced() bits.

On sparc64 we also lack a user/privileged bit in the huge PMDs.

In order to make this work for THP and non-THP builds, some header
file adjustments were necessary.  Namely, provide the PMD_HUGE_* bit
defines and the pmd_large() inline unconditionally rather than
protected by TRANSPARENT_HUGEPAGE.
Reported-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This got missed in the cleanups done for the S390 THP
support.

CC: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "This is primarily to get those r8169 reverts sorted, but other fixes
  have accumulated meanwhile.

   1) Revert two r8169 changes to fix suspend/resume for some users,
      from Francois Romieu.

   2) PCI dma mapping errors in atl1c are not checked for and this cause
      hard crashes for some users, from Xiong Huang.

   3) In 3.8.x we merged the removal of the EXPERIMENTAL dependency for
      'dlm' but the same patch for 'sctp' got lost somewhere, resulting
      in the potential for build errors since there are cross
      dependencies.  From Kees Cook.

   4) SCTP's ipv6 socket route validation makes boolean tests
      incorrectly, fix from Daniel Borkmann.

   5) mac80211 does sizeof(ptr) instead of (sizeof(ptr) * nelem), from
      Cong Ding.

   6) arp_rcv() can crash on shared non-linear packets, from Eric
      Dumazet.

   7) Avoid crashes in macvtap by setting ->gso_type consistently in
      ixgbe, qlcnic, and bnx2x drivers.  From Michael S Tsirkin and
      Alexander Duyck.

   8) Trinity fuzzer spots infinite loop in __skb_recv_datagram(), fix
      from Eric Dumazet.

   9) STP protocol frames should use high packet priority, otherwise an
      overloaded bridge can get stuck.  From Stephen Hemminger.

  10) The HTB packet scheduler was converted some time ago to store
      internal timestamps in nanoseconds, but we don't convert back into
      psched ticks for the user during dumps.  Fix from Jiri Pirko.

  11) mwl8k channel table doesn't set the .band field properly,
      resulting in NULL pointer derefs.  Fix from Jonas Gorski.

  12) mac80211 doesn't accumulate channels properly during a scan so we
      can downgrade heavily to a much less desirable connection speed.
      Fix from Johannes Berg.

  13) PHY probe failure in stmmac can result in resource leaks and
      double MDIO registery later, from Giuseppe CAVALLARO.

  14) Correct ipv6 checksumming in ip6t_NPT netfilter module, also fix
      address prefix mangling, from YOSHIFUJI Hideaki."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
  net, sctp: remove CONFIG_EXPERIMENTAL
  net: sctp: sctp_v6_get_dst: fix boolean test in dst cache
  batman-adv: Fix NULL pointer dereference in DAT hash collision avoidance
  net/macb: fix race with RX interrupt while doing NAPI
  atl1c: add error checking for pci_map_single functions
  htb: fix values in opt dump
  ixgbe: Only set gso_type to SKB_GSO_TCPV4 as RSC does not support IPv6
  net: fix infinite loop in __skb_recv_datagram()
  net: qmi_wwan: add Yota / Megafon M100-1 4g modem
  mwl8k: fix band for supported channels
  bridge: set priority of STP packets
  mac80211: fix channel selection bug
  arp: fix possible crash in arp_rcv()
  bnx2x: set gso_type
  qlcnic: set gso_type
  ixgbe: fix gso type
  stmmac: mdio register has to fail if the phy is not found
  stmmac: fix macro used for debugging the xmit
  Revert "r8169: enable internal ASPM and clock request settings".
  Revert "r8169: enable ALDPS for power saving".
  ...

Pull x86 fixes from Peter Anvin:
 "One (hopefully) last batch of x86 fixes.  You asked for the patch by
  patch justifications, so here they are:

      x86, MCE: Retract most UAPI exports

   This one unexports from userspace a bunch of definitions which should
   never have been exported.  We really don't want to create an
   accidental legacy here.

      x86, doc: Add a bootloader ID for OVMF

   This is a documentation-only patch, just recording the official
   assignment of a boot loader ID.

      x86: Do not leak kernel page mapping locations

   Security: avoid making it needlessly easy for user space to probe the
   kernel memory layout.

      x86/mm: Check if PUD is large when validating a kernel address

   Prevent failures using /proc/kcore when using 1G pages.

      x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems

   Works around a BIOS problem causing boot failures on affected hardware."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Check if PUD is large when validating a kernel address
  x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
  x86, doc: Add a bootloader ID for OVMF
  x86: Do not leak kernel page mapping locations
  x86, MCE: Retract most UAPI exports

Change to my private email, change to my shiny new kernel.org repos,
and drop outdated entry from the former maintainer. Drop my PCA entry,
too, since it belongs to the I2C realm anyhow.
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup.  Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug.  A subsequent PME poll will oops when
it tries to touch the device.

This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list.  This is safe even if the device never
had PME# enabled.

This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.

[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.comReported-and-tested-by: NDaniel J Blueman <daniel@quora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org

This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NSteven Whitehouse <swhiteho@redhat.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We walk through the bind address list and try to get the best source
address for a given destination. However, currently, we take the
'continue' path of the loop when an entry is invalid (!laddr->valid)
*and* the entry state does not equal SCTP_ADDR_SRC (laddr->state !=
SCTP_ADDR_SRC).

Thus, still, invalid entries with SCTP_ADDR_SRC might not 'continue'
as well as valid entries with SCTP_ADDR_{NEW, SRC, DEL}, with a possible
false baddr and matchlen as a result, causing in worst case dst route
to be false or possibly NULL.

This test should actually be a '||' instead of '&&'. But lets fix it
and make this a bit easier to read by having the condition the same way
as similarly done in sctp_v4_get_dst.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>