When omapfb.mode is passed through bootargs, when omapfb is setting mode,
it would check if timings passed are fine for panel attached to it.
It makes use of check_timing API provided by the panel.

In current code if check_timing API is not available for attached panel,
OMAPFB would return -EINVAL and BPP sent via bootargs will not have any effect.

In case of panels like TAAL panel, omapfb or any other driver should not be allowed to
change the timings. So bpps sent via bootargs will not have an effect.

In such case we can check only the x_res and y_res with the panels resolution
and if they match go ahead and set the bpps.
The bpp value sent via bootarg would have an effect.
Signed-off-by: NMayuresh Janorkar <mayur@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add support for Samsung LTE430WQ-F0C to panel-generic-dpi.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS submodules DPI/SDI/DSI/VENC require a regulator to function.
However, if the board doesn't use, say, SDI, the board shouldn't need to
configure vdds_sdi regulator required by the SDI module.

Currently the regulators are acquired when the DSS driver is loaded.
This means that if the kernel is configured with SDI, vdds_sdi regulator
is needed for all boards.

This patch changes the DSS driver to acquire the regulators only when a
display of particular type is initialized. For example, vdds_sdi is
acquired when sdi_init_display() is called.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

MODULE_PARM_DESC() takes the name of the actual module parameter, not the
name of the variable, as input. Fix the module parameter description for
def_disp.
Signed-off-by: NJani Nikula <jani@nikula.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add hwmod device names for OMAP4; this enables device build for omap4 dss
hwmod IPs.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMayuresh Janorkar <mayur@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Enable DSS2 and OMAPFB for OMAP4 in Kconfig
Signed-off-by: NMayuresh Janorkar <mayur@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS code uses ick as one of the clocks in clk_get/clk_put. OMAP4 clock database
doesn't have ick for DSS, so adding ick as dummy clock.

This is needed for backward compatibility with OMAP2/3.

Once pm_runtime* APIs get introduced in DSS, this will be revisited.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The dss struct in dss.c has omap2/3 specific clock names. Making them generic,
to increase readability and extendability.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

enum dss_clock structure is replaced with generic names that
could be used across OMAP2420, 2430, 3xxx, 44xx platforms.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, clock database has <dev, clock-name> tuples for DSS2. Because of
this, the clock names are different across different OMAP platforms.

This patch aligns the DSS2 clock names and roles across OMAP 2420, 2430, 3xxx,
44xx platforms in the clock databases, hwmod databases for opt-clocks, and DSS
clock handling.

This ensures that clk_get/put/enable/disable APIs in DSS can use uniform role
names.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS IRQ number can be obtained from platform_get_irq().  This API in turn
picks the right IRQ number belonging to HW IP from the hwmod database.
So hardcoding of IRQ number could be removed.

This IRQ is stored in dss_irq as part of dss structure, and freed it in
dss_exit().
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS, DISPC, DSI, RFBI, VENC baseaddr can be obtained from platform_get_resource().
This API in turn picks the right silicon baseaddr from the hwmod database.
So hardcoding of base addr could be removed.
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch replaces printk's in the init/probe functions to dev_dbg
for boot time optimization.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DSI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

Also, vdds_dsi regulator handling is copied to dsi.c, since vdds_dsi regulator is
needed by dpi_init() too. Board files are updated accordingly to add 2 instances of
vdds_dsi regulator.

DSI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

Also, venc_vdda_dac reading is moved to venc.c.

VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DISPC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

DISPC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for RFBI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

RFBI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All clock management is moved to dss platform driver. clk_get/put APIs use
dss device instead of core platform device.

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So the device name is changed from omapdss to omapdss_dss in 2420, 2430,
3xxx clock database files. Now the core driver "omapdss" only takes care
of panel registration with the custom bus.
core driver also uses the clk_enable() / clk_disable() APIs exposed by DSS for
clock management.
DSS driver would do clock management of clocks needed by DISPC, RFBI, DSI, VENC

TODO:  The clock content would be adapted to omap_hwmod in a seperate series.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver of DSS is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

DSS platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

As part of omap hwmod changes, DSS will not be the only controller of its
clocks. hwmod initialization also enables the interface clocks, and
manages them.
So, when DSS is built as a module, omap_dss_remove doesn't try to disable
all clocks that have a higher usecount.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove extra vdda_dac supply definition. It was a leftover from conflict
resolution.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Merge branch 'for_2.6.39/pm-misc' of ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus

On the newer ARM processors like CortexA8, CortexA9, the caches can be
speculatively loaded while they are getting flushed.

Clear the SCTLR C bit to prevent further data cache allocation as
part of cache clean routine
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The current code saves few un-necessary registers which are read-only or
write-only, unused CP15 registers.

Remove them and keep only necessary CP15 registers part of
low power context save/restore.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

When L1 cache is suppose to be lost, it needs to be cleaned before
entrering to the low power mode.

While at this, also fix few comments and remove un-necessary
clean_l2 lable.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

omap_sr_probe() creates the smartreflex debug directory and its
underlying nvalue debug directory. These directories are removed in
omap_sr_remove().

Basic smartreflex functionality tested on OMAP3630 Zoom3 & OMAP4430 SDP
Signed-off-by: NAnand S Sawant <sawant@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

 * Build unconditionally as ARM for correct interoperation with
   OMAP firmware.

 * Fix an out-of-range ADR when building for ARM.

 * Remove deprecated PC-relative stores.

 * Add the required ENDPROC() directive for each ENTRY().

 * .align before data words.

 * Handle non-interworking return from v7_flush_dcache_all.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

 * Build unconditionally as ARM for correct interoperation with
   OMAP firmware.

 * Remove deprecated PC-relative stores

 * Add the required ENDPROC() directive for each ENTRY().

 * .align before data words
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Tested-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

For various reasons, Linux now only officially supports being built
with tools which are new enough to understand the SMC instruction.

Replacing the hand-encoded instructions when the mnemonic also
allows for correct assembly in Thumb-2 (otherwise, the result is
random data in the middle of the code).

The Makefile already ensures that this file is built with a high
enough gcc -march= flag (armv7-a).
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Code marked with ENTRY() also needs a matching ENDPROC() directive,
in order to ensure that the type and instruction set of the
symbol are correctly annotated.

ENDPROC() tags the affected symbol as a function symbol, which will
ensure that link-time fixups don't accidentally switch to the
wrong instruction set.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

For CONFIG_THUMB2_KERNEL, the existing definition of do_wfi() will
insert invalid code into the instruction stream.

Any assembler which can assemble Thumb-2 is guaranteed to accept
the "wfi" mnemonic, so for the Thumb-2 case, just use the mnemonic.

The ARM case is left as-is.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

IVA device is not present in many OMAP3 variants.

This patch ensures that initialization is tied to
the presence of IVA on the device.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Voltage control on TWL can be done using VMODE/I2C1/I2C_SR.
Since almost all platforms use I2C_SR on omap3, omap3_twl_init by
default expects that OMAP's I2C_SR is plugged in to TWL's I2C
and calls omap3_twl_set_sr_bit. On platforms where I2C_SR is not connected,
the board files are expected to call omap3_twl_set_sr_bit(false) to
ensure that I2C_SR path is not set for voltage control and prevent
the default behavior of omap3_twl_init.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NShweta Gulati <shweta.gulati@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add a description field to each idle C-state. This helps to give
better data with PowerTop and one don't have to refer to the code
to link what Cx means from system point of view while analysing
PowerTop data.

No functional change.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Remove the custom restore_control_register() and use the exported
set_cr() instead to set the system control register(SCTRL) value.

No functional change.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The OMAP2 and OMAP3 PM code clears clockdomain wakeup and sleep
dependencies.  This is unnecessary after commit
6f7f63cc ("OMAP clockdomain:
initialize clockdomain registers when the clockdomain layer starts")
which clears these dependencies during clockdomain init.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.

Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.

Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: NKevin Hilman <khilman@ti.com>