Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Port the fs_enet driver to support the MDIO on GPIO driver for PHY access
in addition to the mii-bitbang driver.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove our own implementation of I2C bit-banging.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

cxgb3 uses lro_* functions and selects INET_LRO, but this doesn't help unless
INET is already enabled, so make the driver depend on INET also.

sge.c:(.text+0x9f09a): undefined reference to `lro_flush_all'
sge.c:(.text+0x9f62f): undefined reference to `lro_receive_skb'
sge.c:(.text+0x9f8a3): undefined reference to `lro_receive_frags'
sge.c:(.text+0x9fbe0): undefined reference to `lro_vlan_hwaccel_receive_skb'
sge.c:(.text+0x9ffcd): undefined reference to `lro_vlan_hwaccel_receive_frags'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Make driver more readable on standard 80 col windows.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Handle shared IRQ correctly. If IRQ is shared, it typically will show up
as an IRQ with an empty status field. So check in driver and handle it
without crapping out with invalid interrupt message.

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Rx allocation failure at runtime is non-fatal. For normal Rx frame, it
just reuses the buffer, and during setup it just continues with a smaller
receive buffer pool.

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Make this driver compile cleanly on 64 bit platforms.
Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use new netdevice common stats area.

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use skb_padto to pad frames, this avoid allocation of separate buffer just
for dma of the extra bytes.

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add I/O AT DCA (Direct Cache Access) support.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add multi-slice/MSI-X support. By default, a single slice
(and the normal firmware) are used.  To enable msi-x, multi-slice
mode, one must load the driver with myri10ge_max_slices set to
either -1, or something larger than 1.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add several routines that multislices support will use.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Merge branch 'upstream-next-davem' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6

I tried to group recovery related fields nearby (non-CA_Open related
variables, to be more accurate) so that one to three cachelines would
not be necessary in CA_Open. These are now contiguously deployed:

  struct sk_buff_head        out_of_order_queue;   /*  1968    80 */
  /* --- cacheline 32 boundary (2048 bytes) --- */
  struct tcp_sack_block      duplicate_sack[1];    /*  2048     8 */
  struct tcp_sack_block      selective_acks[4];    /*  2056    32 */
  struct tcp_sack_block      recv_sack_cache[4];   /*  2088    32 */
  /* --- cacheline 33 boundary (2112 bytes) was 8 bytes ago --- */
  struct sk_buff *           highest_sack;         /*  2120     8 */
  int                        lost_cnt_hint;        /*  2128     4 */
  int                        retransmit_cnt_hint;  /*  2132     4 */
  u32                        lost_retrans_low;     /*  2136     4 */
  u8                         reordering;           /*  2140     1 */
  u8                         keepalive_probes;     /*  2141     1 */

  /* XXX 2 bytes hole, try to pack */

  u32                        prior_ssthresh;       /*  2144     4 */
  u32                        high_seq;             /*  2148     4 */
  u32                        retrans_stamp;        /*  2152     4 */
  u32                        undo_marker;          /*  2156     4 */
  int                        undo_retrans;         /*  2160     4 */
  u32                        total_retrans;        /*  2164     4 */

...and they're then followed by URG slowpath & keepalive related
variables.

Head of the out_of_order_queue always needed for empty checks, if
that's empty (and TCP is in CA_Open), following ~200 bytes (in 64-bit)
shouldn't be necessary for anything. If only OFO queue exists but TCP
is in CA_Open, selective_acks (and possibly duplicate_sack) are
necessary besides the out_of_order_queue but the rest of the block
again shouldn't be (ie., the other direction had losses).

As the cacheline boundaries depend on many factors in the preceeding
stuff, trying to align considering them doesn't make too much sense.

Commented one ordering hazard.

There are number of low utilized u8/16s that could be combined get 2
bytes less in total so that the hole could be made to vanish (includes
at least ecn_flags, urg_data, urg_mode, frto_counter, nonagle).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch increments the version to 3.93.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some options obtained through shared memory.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch added the 5785 device ID and ASIC revision to the code.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the libphy support.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces code to register and unregister the tg3 mdio bus
with the system.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the TG3_FLG3_USE_PHYLIB flag and applies it to
some select places.  This work makes later patches a little easier to
read.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch applies cleanups that would otherwise clutter later
patches.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves some functions towards the top of the file to avoid
unnecessary function prototypes.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've pushed it down as far as I dare at this point. Someone familiar with
the internal PPP semantics can probably push it further. Another step to
eliminating the old BKL ioctl usage.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/cpmac.c
	net/mac80211/mlme.c

Herbert Xu points out that the use of seperate feature bits for features
to be propagated to VLAN devices is going to get messy real soon.
Replace the VLAN feature bits by a bitmask of feature flags to be
propagated and restore the old GSO_SHIFT/MASK values.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memmove to handle overlapping copy of data.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use netdev_alloc_skb for rx buffer allocation. This sets skb->dev
and can be overriden for NUMA machines.

Change code to return new buffer rather than call by reference.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.

Remove dead code and dead comments.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

 Use netdev_alloc_skb.  This sets skb->dev and allows arch specific
allocation.  Also simplify and cleanup the alignment code.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use netdev_alloc_skb for rx buffer allocation. This sets skb->dev
and can be overriden for NUMA machines.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>