Enable power management. This patch enables the clocks before transfer
and disables after the transfer. It also adds the clock description.
Signed-off-by: NShubhrajyoti Datta <shubhraj@xilinx.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This driver allows an I2C bus to switch between multiple masters. This
is not hot-switching because connected I2C slaves will be
re-instantiated. It is meant to select the best I2C core at runtime once
the task is known. Example: Prefer i2c-gpio over another I2C core
because of HW errata affecting your use case.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

EEPROMs can have additional properties, so they are not suitable for
trivial-devices.txt. Move most bindings to the designated eeprom.txt.
Add the missing "atmel,24c08" while doing that. Note that the remaining
ones in trivial-devices need to be dealt with separately because of
improper manufacturer names.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Broadcoms DSL, CM (cable modem)and STB I2C core implementation have
8 data in/out registers that can transfer 8 bytes or 32 bytes max.
Cable and DSL "Peripheral" i2c cores use single byte per data
register and the STB can use 4 byte per data register transfer.
Adding support to take care of this difference. Accordingly added
the compatible string for SoCs using the "Peripheral" I2C block.
Signed-off-by: NKamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We need this binding because some I2C master drivers will need to adapt
their PM settings for the arbitration circuitry.
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Also, sort the properties alphabetically and make indentation
consistent. Wording largely taken from i2c-rk3x.txt, thanks guys!

Only "i2c-scl-internal-delay-ns" is new, the rest is used by two drivers
already and was documented in their driver binding documentation.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for AMS iAQ-core continuous and pulsed VOC sensors.
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.

Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGao Pan <b54642@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc.  This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc.  This adapter is so simple that
it has no FIFO in it.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.

                         module clock frequency
master clock frequency = ----------------------
                         (ICCL + 6) + (ICCH + 6)

It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.

Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Tested-by: NHemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: NLukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for VZ89X sensors VOC and CO2 reporting channels in
percentage which can be converted to part per million.
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds support for the 10 bit version if Freescale's accelerometers
of this series. The datasheet is available at Freescale's website:

http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8453Q.pdf

It creates a devicetree bindings file to document the new functionality
and removes the driver from the trivial-devices list.
Signed-off-by: NMartin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: NChristoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add pulsedlight vendor to vendor-prefixes.txt, and LIDAR device
documentation to trivial-devices.txt
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Instead of having each i2c driver individually parse device tree data in
case it or platform supports separate wakeup interrupt, and handle
enabling and disabling wakeup interrupts in their power management
routines, let's have i2c core do that for us.

Platforms wishing to specify separate wakeup interrupt for the device
should use named interrupt syntax in their DTSes:

	interrupt-parent = <&intc1>;
	interrupts = <5 0>, <6 0>;
	interrupt-names = "irq", "wakeup";

This patch is inspired by work done by Vignesh R <vigneshr@ti.com> for
pixcir_i2c_ts driver.

Note that the original code tried to preserve any existing wakeup
settings from userspace but was not quite right in that regard:
it would preserve wakeup flag set by userspace upon driver rebinding;
but it would re-arm the wakeup flag if it was disabled by userspace.

We think that resetting the flag upon re-binding the driver is proper
behavior as the driver is responsible for setting up and handling
wakeups.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: NVignesh R <vigneshr@ti.com>
[wsa: updated the commit message]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.

The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Based on i2c-mux-gpio driver, similarly the register-based mux
switch from one bus to another by setting a single register.
The register can be on PCIe bus, local bus, or any memory-mapped
address. The endianness of such register can be specified in device
tree if used, or in platform data.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Acked-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Start a new file which describes the generic bindings used for I2C with
device tree. So we have a central place to look for them, increase
visibility of them, and hopefully reduce the amount of custom properties
introduced.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NVaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The I2C dir is not for I2C client devices! Move it to the proper folder.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

The I2C dir is not for I2C client devices! Move it to the proper folder.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

The I2C dir is not for I2C client devices! Move it to the proper folder.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

The I2C dir is not for I2C client devices! Move it to the proper folder.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NPavel Machek <pavel@denx.de>

This adds devicetree documentation for the bindings of the
ads7828 driver.
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: NAnurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: NIan Molton <ian.molton@codethink.co.uk>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: NKamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

add a new value "atmel,sama5d2-i2c" for the "compatible" property.
add a new optional property "atmel,fifo-size" to enable FIFO support when
available.
add missing optional properties "dmas" and "dma-names".
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: NXudong Chen <xudong.chen@mediatek.com>
Signed-off-by: NLiguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: NEddie Huang <eddie.huang@mediatek.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

DT nodes should use the more specific adi,adxl345 and adi,adxl346
compatible values instead. As the ADXL346 is backward-compatible with
the ADXL345, ADXL346 nodes must list both adi,adxl346 and adi,adxl345,
in that order.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: NFeng Kan <fkan@apm.com>
Signed-off-by: NHieu Le <hnle@apm.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: NSubhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Reviewed-by: NRay Jui <rjui@broadcom.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Having a board where the I2C bus locks up occasionally made it clear
that the bus recovery in the i2c-davinci driver will only work on
some boards, because on regular boards, this will only toggle GPIO
lines that aren't muxed to the actual pins.

The I2C controller on SoCs like da850 (and da830), Keystone 2 has the
built-in capability to bit-bang its lines by using the ICPFUNC registers
of the i2c controller.
Implement the suggested procedure by toggling SCL and checking SDA using
the ICPFUNC registers of the I2C controller when present. Allow platforms
to indicate the presence of the ICPFUNC registers with a has_pfunc platform
data flag and add optional DT property "ti,has-pfunc" to indicate
the same in DT.
Reviewed-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: NMichael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: NMike Looijmans <milo-software@users.sourceforge.net>
[grygorii.strashko@ti.com: combined patches from Ben Gardiner and
Mike Looijmans and reimplemented ICPFUNC bus recovery using I2C
bus recovery infrastructure]
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Adds the i2c bus controller driver for the Ingenic JZ4780 SoC.
Signed-off-by: NZubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patchset attempts to standardize the naming of dt-bindings
documents based on the Broadcom vendor prefix of brcm.

Although there are no guidelines currently present for how to name
the dt-bindings document the "vendor,binding.txt" style is in use by
some of the other vendors.
Acked-by: NLee Jones <lee@kernel.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NGregory Fong <gregory.0xf0@gmail.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NRob Herring <robh@kernel.org>

The CX92755 is an SoC in the Conexant Digicolor series. The devicetree binding
document describes the I2C controller on the CX92755 SoC, that is also shared
by some other SoCs in the Digicolor series. The driver adds support.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
[wsa: fixed spaces around operators]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>