In some cases, the device or firmware may be busy when the
driver attempts to perform the CRQ initialization handshake.
If the partner is busy, the hypervisor will return the H_CLOSED
return code. The aim of this patch is that, if the device is not
ready, to query the device a number of times, with a small wait
time in between queries. If all initialization requests fail,
the driver will remain in a dormant state, awaiting a signal
from the device that it is ready for operation.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unneeded return value cast.
This is detected by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove dma_alloc_coherent return value cast.
This is detected by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no caller in tree.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no caller in tree any more.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new bit TX_GENF_CLR_EN has been added in AM65x SR2.0 to fix i2083
errata, which can be just set unconditionally for all SoCs.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

W=1 warnings indicated that 'rc' was unused in efx_mcdi_set_id_led();
 change the function to return int instead of void and plumb the rc
 through the caller efx_ethtool_phys_id().
Since (post-Falcon) all sfc NICs use MCDI for this, there's no point in
 indirecting through a nic_type method, so remove that and just call
 efx_mcdi_set_id_led() directly.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Missing 'struct' keyword caused "cannot understand function prototype"
 warnings.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks to some past refactor, 'spec' is not actually used in this
 function; the code using it moved to the callee efx_farch_filter_remove.
Remove the variable to fix a W=1 warning.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of these RX-event flags aren't used at all, so remove them.
Others are used only #ifdef DEBUG to log a message; suppress the
 unused-var warnings #ifndef DEBUG with a void cast.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add debugfs node for querying function table, for example:
cat /sys/kernel/debug/hinic/0000:15:00.0/func_table/valid
Signed-off-by: NLuo bin <luobin9@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add debugfs node for querying rq info, for example:
cat /sys/kernel/debug/hinic/0000:15:00.0/RQs/0x0/rq_hw_pi
Signed-off-by: NLuo bin <luobin9@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add debugfs node for querying sq info, for example:
cat /sys/kernel/debug/hinic/0000:15:00.0/SQs/0x0/sq_pi
Signed-off-by: NLuo bin <luobin9@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test for dma_need_sync earlier to increase
performance. xsk_buff_dma_sync_for_cpu() takes an xdp_buff as
parameter and from that the xsk_buff_pool reference is dug out. Perf
shows that this dereference causes a lot of cache misses. But as the
buffer pool is now sent down to the driver at zero-copy initialization
time, we might as well use this pointer directly, instead of going via
the xsk_buff and we can do so already in xsk_buff_dma_sync_for_cpu()
instead of in xp_dma_sync_for_cpu. This gets rid of these cache
misses.

Throughput increases with 3% for the xdpsock l2fwd sample application
on my machine.
Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NBjörn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-11-git-send-email-magnus.karlsson@intel.com

Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.
Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NBjörn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-3-git-send-email-magnus.karlsson@intel.com

Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NBjörn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com

Convert tx_timeout handler to not do the full reset.  As this was
the last user of ionic_reset_queues(), we can drop it.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add to our new ionic_reconfigure_queues() to also be able to change
the number of queues in use, and to change the queue interrupt layout
between split and combined.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original way of changing ring length was to completely
tear down the lif's queue structure and then rebuild it, while
running the risk of allocations that might fail in the middle
and leave us with a broken driver.

Instead, we can set up all the new queue and descriptor
allocations first, then swap them out and delete the old
allocations.  If the new allocations fail, we report the error,
stay with the old setup and continue running.  This gives us
a safer path, and a smaller window of time where we're not
processing traffic.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We really don't need to tear down and rebuild the whole queue structure
when changing the MTU; we can simply stop the queues, clean and refill,
then restart the queues.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use index counters rather than pointers for tracking head
and tail in the queues to save a little memory and to perhaps
slightly faster queue processing.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split out the queue descriptor blocks into separate dma
allocations to make for smaller blocks.
Co-developed-by: NNeel Patel <neel@pensando.io>
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ionic_open() and ionic_stop() are not referenced outside of their
defining file, so make them static.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a block of stats structs attached to the lif instead of
little ones attached to each qcq.  This simplifies our memory
management and gets rid of a lot of unnecessary indirection.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we aren't yet supporting multiple lifs, we can remove
complexity by removing the list concept and related code,
to be re-engineered later when actually needed.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use kcalloc for allocating arrays of structures.

Following along after
commit e71642009cbdA ("ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()")
there are a couple more array allocations that can be converted
to using devm_kcalloc().
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the queue name displayed.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NIC might tell us its minimum MTU, but let's be sure not
to use something smaller than ETH_MIN_MTU.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This header file is currently included into the ethernet driver via a
relative path into the PHY subsystem. This is bad practice, and causes
issues for the upcoming move of the MDIO driver. Move the header file
into include/linux to clean this up.

v2:
Move header to include/linux/mdio
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs

Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.

v2:
Add include/linux/pcs

v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: NRikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: NRikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only usage of qca_serdev_ops is to pass its address to
serdev_device_set_client_ops() which takes a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: NRikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These two functions share the majority of the code, hence merge
them together. In the meanwhile, add a reset pass-in parameter
to differentiate them. Thus, the code is easier to read and to tell
the difference between reset_init and regular init.
Signed-off-by: NLijun Pan <ljp@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the beginning of the function, from_passive_init is set false by
"adapter->from_passive_init = false;",
hence the if statement will never run.
Signed-off-by: NLijun Pan <ljp@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When H_SEND_CRQ command returns with H_CLOSED, it means the
server's CRQ is not ready yet. Instead of resetting immediately,
we wait for the server to launch passive init.
ibmvnic_init() and ibmvnic_reset_init() should also return the
error code from ibmvnic_send_crq_init() call.
Signed-off-by: NLijun Pan <ljp@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of comparing (adapter->init_done_rc == 1), let it
be (adapter->init_done_rc == PARTIALSUCCESS).
Signed-off-by: NLijun Pan <ljp@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A single cacheline might not contain the packet header for
small L1_CACHE_BYTES values.
Use net_prefetch() as it issues an additional prefetch
in this case.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A single cacheline might not contain the packet header for
small L1_CACHE_BYTES values.
Use net_prefetch() as it issues an additional prefetch
in this case.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>