Add full support for both AP and STA for management frame protection.
Reviewed-by: NArend Van Spriel <arend.van@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

brcmf_add_keyext is called when a key is configured for a specific
mac address. This function is very similar to the calling function
brcmf_add_key. Integrate this function and also use existing del_key
function in case key is to be cleared.
Reviewed-by: NArend Van Spriel <arend.van@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge module parameters and platform data in one struct. This is the
last step to move to the new platform data per device. Now parameters
of platform data will be merged with module parameters per device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Platform data is only available for sdio. With this patch a new
platform data structure is being used which allows for platform
data for any device and configurable per device. This patch only
switches to the new structure and adds support for SDIO devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently ARP and ND (IPv6 Neigbor Discovery) offload get disabled
on entering suspend. However when firmwares support the wowl_cap
iovar then these offload routines can be kept enabled as they
will work during WOWL as well.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In preparation of module parameters for all devices the module
platform data retrieval is moved from sdio to common. It is still
only used for sdio devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for gtk rekeying offload and for gtk
rekeying failure during wowl mode.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In preparation of module parameters for all devices the module init
and exit routines are moved to the common file.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When keys get set and updated this has to happen after eapol got
transmitted (without key or old key) before the key can be updated.
To make sure the order of sending eapol and configuring key is done
correctly a timeout for tx of eapol is applied. This timeout is set
to 50 msec, which is not always enough. Especially in AP mode and
key updates the timeout may need to be much longer because client(s)
can be in powersave. Increase the timeout from 50 to 950 msec.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The PCIE bus driver supports older gen1 (v1) chips, but there is no
actual device which is using this older pcie core which is supported
by brcmfmac. Remove all gen1 related code.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A newer version of the 4366 PCIE chip has been released. Add
support for this version of the chip.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The PCIE bar1 window size is specified by chip. Currently the
ioremap of bar1 was using a define which always matched the size
of bar1, but newer chips can have a different bar1 sizes. With
this patch the ioremap will be called with the by chip provided
window size.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer type pcie devices have memory which get shared between fw and
hw. The division of this memory is done firmware compile time. As a
result the ramsize as used by driver needs to be adjusted for this.
This is done by reading the memory size from the firmware.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The return value of iovar set function should be saved and checked.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Configure ipv6 address for neighbor discovery offload ip table in
firmware obtained through ipv6 address notification callback.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add additional length checks on firmware events to create more
robust code.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NLei Zhang <leizh@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Country code configuration in a device is a device specific
operation. For this the country code as specified by reg notifier
(iso3166 alpha2) needs to be translated to a device specific
country locale and revision number. This patch adds this
translation and puts a placeholder in the device specific settings
where the translation table can be stored. Additional patches will
be needed to read these tables from for example device platform
data.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In some cases wiphy->wowlan could be NULL if firmware doesn't have the
support. Driver should check for support before walking down the feature
flags.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some systems have problems with allocating memory allocation larger
then 64K. Often on unload/load or suspend/resume a failure is
reported: Could not allocate wiphy device. This patch makes the
escan intermediate storage buf dynamically allocated, and smaller
than 64K.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Dropping the '_timeout' from the function name as the fact that a timeout
value is passed makes it obvious a timeout is used. Also helps to keep code
lines a bit shorter and easier to stick to 80 char boundary.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

New generation devices have firmware which has more than 256 flowrings.
E.g. following debugging message comes from 14e4:4365 BCM4366:
[  194.606245] brcmfmac: brcmf_pcie_init_ringbuffers Nr of flowrings is 264

At various code places (related to flowrings) we were using u8 which
could lead to storing wrong number or infinite loops when indexing with
this type. This issue was quite easy to spot in brcmf_flowring_detach
where it led to infinite loop e.g. on failed initialization.

This patch switches code to proper types and increases the maximum
number of supported flowrings to 512.

Originally this change was sent in September 2015, but back it was
causing a regression on BCM43602 resulting in:
Unable to handle kernel NULL pointer dereference at virtual address ...

The reason for this regression was missing update (s/u8/u16) of struct
brcmf_flowring_ring. This problem was handled in 9f64df94 ("brcmfmac: Fix
bug in flowring management."). Starting with that it's safe to apply
this original patch as it doesn't cause a regression anymore.

This patch fixes an infinite loop on BCM4366 which is supported since
4.4 so it makes sense to apply it to stable 4.4+.

Cc: <stable@vger.kernel.org> # 4.4+
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On a Radxa Rock2 board with a Ampak AP6335 (Broadcom 4339 core) it seems
the card responds very quickly most of the time, unfortunately during
initialisation it sometimes seems to take just a bit over 2 seconds to
respond.

This results intialization failing with message like:
  brcmf_c_preinit_dcmds: Retreiving cur_etheraddr failed, -52
  brcmf_bus_start: failed: -52
  brcmf_sdio_firmware_callback: dongle is not responding

Increasing the timeout to allow for a bit more headroom allows the
card to initialize reliably.

A quick search online after diagnosing/fixing this showed that Google
has a similar patch in their ChromeOS tree, so this doesn't seem
specific to the board I'm using.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Platform NVRAM (stored on a flash partition) has entries separated by a
NULL (\0) char. Our parsing code switches from VALUE state to IDLE
whenever it meets a NULL (\0). When that happens our IDLE handler should
simply consume it and analyze whatever is placed ahead.

This fixes harmless warnings spamming debugging output:
[  155.165624] brcmfmac: brcmf_nvram_handle_idle warning: ln=1:col=20: ignoring invalid character
[  155.180806] brcmfmac: brcmf_nvram_handle_idle warning: ln=1:col=44: ignoring invalid character
[  155.195971] brcmfmac: brcmf_nvram_handle_idle warning: ln=1:col=63: ignoring invalid character
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On Broadcom ARM routers BCM4366 cards are available with 14e4:4365 ID.
Unfortunately this ID was already used by Broadcom for cards with
BCM43142, a totally different chipset requiring SoftMAC driver. To avoid
a conflict between brcmfmac and bcma use more specific ID entry with
subvendor and subdevice specified.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On recent Broadcom chipsets PMU is present as separated core and it
can't be accessed using ChipCommon anymore as it fails with e.g.:
[   18.198412] Unhandled fault: imprecise external abort (0x1406) at 0xb6da200f

Add a new helper function that will return a proper core that should be
used for accessing PMU registers.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is an extra bitfield with info about some present hardware.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Separated PMU core can be found in new devices and should be used for
accessing PMU registers (which were routed through ChipCommon so far).
This core is one of exceptions that doesn't have or need wrapper address
to be still safely accessible.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far we were looking for address descriptors without a check for
crossing current component border. In case of dealing with unsupported
descriptor or descriptor missing at all the code would incorrectly get
data from another component.

Consider this binary-described component from BCM4366 EROM:
4bf83b01	TAG==CI		CID==0x83b
20080201	TAG==CI		PORTS==0+1	WRAPPERS==0+1
18400035	TAG==ADDR	SZ_SZD		TYPE_SLAVE
00050000
18107085	TAG==ADDR	SZ_4K		TYPE_SWRAP

Driver was assigning invalid base address to this core:
brcmfmac:  [6 ] core 0x83b:32 base 0x18109000 wrap 0x18107000
which came from totally different component defined in EROM:
43b36701	TAG==CI		CID==0x367
00000201	TAG==CI		PORTS==0+1	WRAPPERS==0+0
18109005	TAG==ADDR	SZ_4K		TYPE_SLAVE

This change will also allow us to support components without wrapper
address in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

First of all it changes the way we calculate primary channel offset. If
we use e.g. 80 MHz channel with primary frequency 5180 MHz (which means
center frequency is 5210 MHz) it makes sense to calculate primary offset
as -30 MHz.
Then it fixes values we compare primary_offset with. We were comparing
offset in MHz against -2 or 2 which was resulting in picking a wrong
primary channel.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With commit 7d34b056 ("brcmfmac: Move all module parameters to
one place") a bug was introduced causing a null pointer exception.
This patch fixes the bug by initializing the sg table till after
the settings have been initialized.

Fixes: 7d34b056 ("brcmfmac: Move all module parameters to one place")
Reported-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

linux/module.h is required for defining module parameters
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With gcc < 4.3 __UNIQUE_ID does not create unique ids with the macro
BRCMF_FW_NVRAM_DEF. Fix this by removing the MODULE_FIRMWARE instance
for the nvram file. This file is not in linux-firmware repo so it may
not be needed anyway. Otherwise consider this as a temporary fix.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NArend van Spriel <aspriel@gmail.com>
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Tested-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sometimes on module reload and reconnect to ibss a deauth from
other station can be received. This is treated as a link down but
for ibss this is wrong. It will close the interface and no data
is possible. Ignore the firmware generated link down events in
ibss mode, as ibss is always teared down by cfg80211.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The btcoex uses a timeout which was in milliseconds and got
converted to jiffies upon using timer api. Instead, convert
it to jiffies and treat it as such further.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead to having macro definition for millisecond timeout have
the definition directly in jiffies. This makes the unit of the
value immediately clear and may result in code that is bit more
compact.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The function brcmf_sdio_wd_timer() has wdtick parameter. However, it
is only called with two values and as such the parameter is replaced
with boolean value indicating the timer should be active or not.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Function prototype forward declarations are to be avoided. This
patch shuffles some of the functions so the forward declarations
can be removed.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With wowl net detect it becomes possible to scan for specific ssids
and wakeup once found.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The module parameter can be used to ensure the probe succeeds thus
claiming the device and allowing post-mortem debugging in case of
firmware crash. It is only available when select CONFIG_BRCMDBG.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>