It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.

Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make it easier to grep for htt rx errors.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Show message length and expected length.  Helps debug
firmware mismatch issues.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Aids in understanding excactly what a firmware is
offering.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is required to call put_device() if device_register() fails, so that
we give up the last reference to the device.  Calling put_device allows
for mdiobus_release to be executed, kfreeing the bus.
Signed-off-by: NLevente Kurusa <levex@linux.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.

Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.

kvalo: change the warning message
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If recovery failed ath10k returned 0 (success) and
mac80211 continued to call other driver callbacks.
This caused null dereference.

This is how the failure looked like:

ath10k: ctl_resp never came in (-110)
ath10k: failed to connect to HTC: -110
ath10k: could not init core (-110)
BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nf_nat_ipv4 ]
CPU: 1 PID: 36 Comm: kworker/1:1 Tainted: G        WC   3.13.0-rc8-wl-ath+ #8
Hardware name: To be filled by O.E.M. To be filled by O.E.M./HURONRIVER, BIOS 4.6.5 05/02/2012
Workqueue: events ieee80211_restart_work [mac80211]
task: ffff880215b521c0 ti: ffff880215e18000 task.ti: ffff880215e18000
RIP: 0010:[<ffffffffa0b355c1>]  [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
RSP: 0018:ffff880215e19af8  EFLAGS: 00010292
RAX: ffff880215e19b10 RBX: 0000000000000000 RCX: 0000000000000018
RDX: 00000000d9ccf800 RSI: ffff8800c965ad00 RDI: 0000000000000000
RBP: ffff880215e19b58 R08: 0000000000000002 R09: 0000000000000000
R10: ffffffff812e1a23 R11: 0000000000000292 R12: 0000000000000018
R13: 0000000000000000 R14: 0000000000000002 R15: ffff88021562d700
FS:  0000000000000000(0000) GS:ffff88021fa80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000001a0d000 CR4: 00000000000407e0
Stack:
 d9ccf8000d47df40 ffffffffa0b367a0 ffff880215e19b10 0000000000000010
 ffff880215e19b68 ffff880215e19b28 0000000000000018 ffff8800c965ad00
 0000000000000018 0000000000000000 0000000000000002 ffff88021562d700
Call Trace:
 [<ffffffffa0b3251d>] ath10k_pci_hif_send_head+0xa7/0xcb [ath10k_pci]
 [<ffffffffa0b16cbe>] ath10k_htc_send+0x23d/0x2d0 [ath10k_core]
 [<ffffffffa0b1a169>] ath10k_wmi_cmd_send_nowait+0x5d/0x85 [ath10k_core]
 [<ffffffffa0b1aaef>] ath10k_wmi_cmd_send+0x62/0x115 [ath10k_core]
 [<ffffffff814e8abd>] ? __netdev_alloc_skb+0x4b/0x9b
 [<ffffffffa0b1c438>] ath10k_wmi_vdev_set_param+0x91/0xa3 [ath10k_core]
 [<ffffffffa0b0e0d5>] ath10k_mac_set_rts+0x3e/0x40 [ath10k_core]
 [<ffffffffa0b0e1d0>] ath10k_set_frag_threshold+0x5e/0x9c [ath10k_core]
 [<ffffffffa09d60eb>] ieee80211_reconfig+0x12a/0x7b3 [mac80211]
 [<ffffffff815a8069>] ? mutex_unlock+0x9/0xb
 [<ffffffffa09b3a40>] ieee80211_restart_work+0x5e/0x68 [mac80211]
 [<ffffffff810c01d0>] process_one_work+0x1d7/0x2fc
 [<ffffffff810c0166>] ? process_one_work+0x16d/0x2fc
 [<ffffffff810c06c8>] worker_thread+0x12e/0x1fb
 [<ffffffff810c059a>] ? rescuer_thread+0x27b/0x27b
 [<ffffffff810c5aee>] kthread+0xb5/0xbd
 [<ffffffff815a9220>] ? _raw_spin_unlock_irq+0x28/0x42
 [<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
 [<ffffffff815ae04c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
Code: df ff d0 48 83 c4 18 5b 41 5c 41 5d 5d c3 55 48 89 e5 41 57 41 56 45 89 c6 41 55 41 54 41 89 cc 53 48 89
RIP  [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
 RSP <ffff880215e19af8>
CR2: 0000000000000000
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The commit 1d3ee88a
(bonding: add netlink attributes to slave link dev)
has add rtmsg_ifinfo() in bond_set_active_slave() and
bond_set_backup_slave(), so the two function need to
called in RTNL lock, but bond_loadbalance_arp_mon()
only calling these functions in RCU, warning message
will occurs.

fix this by add a new function bond_slave_state_change(),
which will reset the slave's state after slave link check,
so remove the bond_set_xxx_slave() from the cycle and only
record the slave_state_changed, this will call the new
function to set all slaves to new state in RTNL later.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A file descriptor opened for /dev/net/tun and a tun device are
connected with ioctl.  Though understanding the connection is
important for trouble shooting, no way is given to a user to know
the connected device for a given file descriptor at userland.

This patch adds a new fdinfo field for the device name connected to
a file descriptor opened for /dev/net/tun.

Here is an example of the field:

    # lsof | grep tun
    qemu-syst 4565         qemu   25u      CHR             10,200       0t138      12921 /dev/net/tun
    ...

    # cat /proc/4565/fdinfo/25
    pos:	138
    flags:	0104002
    iff:	vnet0

    # ip link show dev vnet0
    8: vnet0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 ...

changelog:

    v2: indent iff just like the other fdinfo fields are.
    v3: remove unused variable.
        Both are suggested by David Miller <davem@davemloft.net>.
Signed-off-by: NMasatake YAMATO <yamato@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user tried to change generic options using "ethtool -s" command, while SFP
module is plugged out or during module detection, the command would have failed
with "Unsupported port type" message. The fix is to ignore the port option in
case it's same as the current port configuration.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was returning from link event handler without
setting linkup variable
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o __qlcnic_down call's netif_tx_disable which in turn stops
  all the TX queues, corresponding start queue was missing in
  __qlcnic_up which was leading to tx timeout.
o The commit b84caae4
  (qlcnic: Fix usage of netif_tx_{wake, stop} api during link change.)
  exposed this issue.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Do not re-initialize vlan list in case of adapter reset.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Bound checks should be >= instead of > for number of receive descriptors
  and number of receive rings.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b0 ("i40e: add DCB and DCBNL support")
Signed-off-by: NDave Jones <davej@fedoraproject.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes grant transfer releasing code from netfront, and uses
gnttab_end_foreign_access to end grant access since
gnttab_end_foreign_access_ref may fail when the grant entry is
currently used for reading or writing.

* clean up grant transfer code kept from old netfront(2.6.18) which grants
pages for access/map and transfer. But grant transfer is deprecated in current
netfront, so remove corresponding release code for transfer.

* fix resource leak, release grant access (through gnttab_end_foreign_access)
and skb for tx/rx path, use get_page to ensure page is released when grant
access is completed successfully.

Xen-blkfront/xen-tpmfront/xen-pcifront also have similar issue, but patches
for them will be created separately.

V6: Correct subject line and commit message.

V5: Remove unecessary change in xennet_end_access.

V4: Revert put_page in gnttab_end_foreign_access, and keep netfront change in
single patch.

V3: Changes as suggestion from David Vrabel, ensure pages are not freed untill
grant acess is ended.

V2: Improve patch comments.
Signed-off-by: NAnnie Li <annie.li@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow us to use bigger receive buffer, and prevent allocation failure
due to fragmented memory.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is race condition when call netif_napi_add() after
register_netdevice(), as ->open() can be called without napi initialized
and trigger BUG_ON() on napi_enable(), like on below messages:

[    9.699863] sky2: driver version 1.30
[    9.699960] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 2
[    9.700020] sky2 0000:02:00.0: irq 45 for MSI/MSI-X
[    9.700498] ------------[ cut here ]------------
[    9.703391] kernel BUG at include/linux/netdevice.h:501!
[    9.703391] invalid opcode: 0000 [#1] PREEMPT SMP
<snip>
[    9.830018] Call Trace:
[    9.830018]  [<fa996169>] sky2_open+0x309/0x360 [sky2]
[    9.830018]  [<c1007210>] ? via_no_dac+0x40/0x40
[    9.830018]  [<c1007210>] ? via_no_dac+0x40/0x40
[    9.830018]  [<c135ed4b>] __dev_open+0x9b/0x120
[    9.830018]  [<c1431cbe>] ? _raw_spin_unlock_bh+0x1e/0x20
[    9.830018]  [<c135efd9>] __dev_change_flags+0x89/0x150
[    9.830018]  [<c135f148>] dev_change_flags+0x18/0x50
[    9.830018]  [<c13bb8e0>] devinet_ioctl+0x5d0/0x6e0
[    9.830018]  [<c13bcced>] inet_ioctl+0x6d/0xa0

To fix the problem patch changes the order of initialization.

Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=67151

Reported-and-tested-by: ebrahim.azarisooreh@gmail.com
Signed-off-by: NStanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel already has this information, and individual drivers
shouldn't duplicate that.  This also eliminates the use of __DATE__ and
__TIME__, which make the build non-deterministic.
Signed-off-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

Currently we're calling it from under RCU context, however we're using some
functions that require rtnl to be held.

Fix this by restructuring the locking - don't call it under any locks,
aquire rcu_read_lock() if we're sending _only_ (i.e. we have the active
slave present), and use rtnl locking otherwise - if we need to modify
(in)active flags of a slave.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently bond_ab_arp_probe() is always called under rcu_read_lock(),
however to work with curr_active_slave we're still holding the
curr_slave_lock.

To remove that curr_slave_lock - rcu_dereference the bond's
curr_active_slave and use it further - so that we're sure the slave won't
go away, and we don't care if it will change in the meanwhile.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Submission d9aee591 "bnx2x: Don't release PCI bars on shutdown" separated
the PCI remove and shutdown flows, but pci_disable_device() is still
being called on both.
As a result, a dev_WARN_ONCE will be hit during shutdown for every bnx2x
VF probed on a hypervisor (as its shutdown callback will be called and later
pci_disable_sriov() will call its remove callback).

This calls the pci_disable_device() only on the remove flow.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Logging the MAC address on every if-up, is not really useful, and annoying when
there is no cable inserted and NetworkManager tries the ifup every 50 seconds.

Also change the log level from warning to info, as that is what it is.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Logging a PTP error on hw which simply does not support PTP is not very
useful. Moreover this message gets logged on every if-up, and if there is
no cable inserted NetworkManager will re-try the ifup every 50 seconds.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/8390/apne.c: In function ‘apne_probe1’:
drivers/net/ethernet/8390/apne.c:215: warning: unused variable ‘ei_local’

Introduced by commit c45f812f ("8390 :
Replace ei_debug with msg_enable/NETIF_MSG_* feature"), which added the
variable without using it.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The adapter is freed before we check its flags. It was caused
by commit 144be3d9 ("net/cxgb4: Avoid disabling PCI device for
towice"). The problem was reported by Intel's "0-day" tool.

The patch fixes it to avoid reverting commit 144be3d9.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now ath10k used a copy-by-value beacon
submission.

The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.

This also fixes strange bug when multicast traffic
would freeze TX indefinitely.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Most channel switching logic has been implemented
already so this patch is pretty small. The patch
makes use of mac80211's vif->csa_active for AP CSA
handling.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Until now channel change wasn't propagating to FW
directly because operational channel is abstracted
by VDEVs and it wasn't really necessary since
ath10k implements hwscan and hwroc.

This effectively fixes STA CSA and allows for
future AP-like CSA as well.

kvalo: change error handling in ath10k_bss_info_changed()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Refactored MSI-x vector calculation for All adapters.
  Decoupled logic in the code which was using same call to
  request MSI-x vectors in default driver load, as well as
  during set_channel() operation for TSS/RSS. This refactoring
  simplifies code for TSS/RSS code path as well as probe path
  of the driver load for all adapters.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Refactor configuration of interrupt coalescing parameters for
  all supported adapters.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for MSI/MSI-X mode in poll controller routine.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Added hardware ops for interrupt enable/disable functions
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Dump each Tx queue details with all descriptors, queue indices
  and Tx queue stats to imporve data colletion in situations
  where Tx timeout occurs.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Use boolean type instead of u8.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the option conversion downdelay and updelay divide a u64
and on a 32 bit this causes the following errors:
ERROR: "__udivdi3" [drivers/net/bonding/bonding.ko] undefined!
ERROR: "__umoddi3" [drivers/net/bonding/bonding.ko] undefined!

Fix it by using a normal int instead because newval->value is capped
at INT_MAX by the way the option is defined.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of a workaround for a hardware erratum in the SFC9100 family
(SF bug 35388), the TX_DESC_UPD_DWORD register address is also used
for communicating with the event block, and only descriptor pointer
values < 2048 are valid.

If the TX DMA ring size is increased to 4096 descriptors (which the
firmware still allows) then we may write a descriptor pointer
value >= 2048, which has entirely different and undesirable effects!

Limit the TX DMA ring size correctly when this workaround is in
effect.

Fixes: 8127d661 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>