The driver that used the 'nodisconnect' parameter was removed in commit
565bae6a ("[SCSI] 53c7xx: kill driver"). Related documentation was
cleaned up in commit f37a7238 ("[SCSI] 53c7xx: fix removal
fallout"), except for the remaining two mentions that are removed here.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: NWei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Julia pointed out beiscsi_boot_get_sinfo does not unlock mbox_lock on
nonemb_cmd memory allocation failure.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

alloc_wrb_handle already does memset zero of iscsi_wrb descriptor so
remove redundant memset in WRB submission paths.

Add pwrb_handle NULL check before memsett'ing pwrb.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We know that 'ret' is not an error code because it has been tested a few
lines above.  So, if one of these function fails, 0 will be returned
instead of an error code.  Return -ENOMEM instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>

'ret' needs to be set with error code if hba_setup_cid_tbls fails.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(unsigned long)' which is likely to
be 4.

It is likely that the number of bits in a long was expected here, so use
BITS_PER_LONG instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: NSumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The MULDIV macro is essentially a duplicate of the more standard
mult_frac macro. Replace use of MULDIV with mult_frac & drop the
duplication.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Calculating the maximum timeout that a user can set via the
SG_SET_TIMEOUT ioctl involves multiplying INT_MAX by USER_HZ/HZ. If
USER_HZ is larger than HZ then this results in an overflow when
performed as a 32 bit integer calculation, resulting in compiler
warnings such as the following:

  drivers/scsi/sg.c: In function 'sg_ioctl':
  drivers/scsi/sg.c:91:67: warning: integer overflow in expression [-Woverflow]
   #define MULDIV(X,MUL,DIV) ((((X % DIV) * MUL) / DIV) + ((X / DIV) * MUL))
                                                                     ^
  drivers/scsi/sg.c:887:14: note: in expansion of macro 'MULDIV'
     if (val >= MULDIV (INT_MAX, USER_HZ, HZ))
                ^
  drivers/scsi/sg.c:91:67: warning: integer overflow in expression [-Woverflow]
   #define MULDIV(X,MUL,DIV) ((((X % DIV) * MUL) / DIV) + ((X / DIV) * MUL))
                                                                     ^
  drivers/scsi/sg.c:888:13: note: in expansion of macro 'MULDIV'
         val = MULDIV (INT_MAX, USER_HZ, HZ);
               ^

Avoid this overflow by performing the (constant) arithmetic on 64 bit
integers, which ensures that overflow from multiplying the 32 bit values
cannot occur. When converting the result back to a 32 bit integer use
min_t to ensure that we don't simply truncate a value beyond INT_MAX to
a 32 bit integer, but instead use INT_MAX where the result was larger
than it. As the values are all compile time constant the 64 bit
arithmetic should have no runtime cost.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ibmvfc driver currently doesn't support FC Class 3 Error Recovery.
However, it is simply a matter of informing the VIOS that the payload
expects to use sequence level error recovery via a bit flag in the
ibmvfc_cmd structure.

This patch adds a module parameter to enable error recovery support at
boot time. When enabled the RETRY service parameter bit is set during
PRLI, and ibmvfc_cmd->flags includes the IBMVFC_CLASS_3_ERR bit.
Signed-off-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The READ FCP_XFER_READY DISABLED bit is required to always be set to one
since FCP-3. Set it in the service parameter page frame during process
login.
Signed-off-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It is likely that checking the result of 'pci_write_config_dword' is
expected here.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Runtime PM should be configured already once we call device_add. See
also the description in this mail thread
https://lists.linuxfoundation.org/pipermail/linux-pm/2009-November/023198.html
or the order of calls e.g. in usb_new_device.

The changed order also helps to avoid scenarios where runtime pm for
&shost->shost_gendev is activated whilst the parent is suspended,
resulting in error message "runtime PM trying to activate child device
hostx but parent yyy is not active".

In addition properly reverse the runtime pm calls in the error path.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch implements functions for pushing HCAM (host controlled
asynchronous messages) error buffers to userspace through sysfs
attributes.  Reads to the "async_err_log" attribute will result in a
single HCAM buffer being copied to userspace; one can process the next
HCAM buffer by writing any string to the same attribute.

A new list was added to the ioa_cfg structure to store the HCAM buffers
for later reporting. We also send a KOBJ_CHANGE event whenever a new
HCAM buffer is made available to userspace.
Signed-off-by: NHeitor Ricardo Alves de Siqueira <halves@linux.vnet.ibm.com>
Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When a tmf is issued, various response codes can be returned from the
target. For a query tmf the response may be TMF_RESP_FUNC_COMPLETE or
TMF_RESP_FUNC_SUCC.  Add a condition for TMF_RESP_FUNC_SUCC to
hisi_sas_exec_internal_tmf_task().  This affects query tmf, as the
result is success the returned value was for failure.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When the port is detached we cannot execute a TMF, as there can be no
device attached to the port.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add code in slot_complete_v2_hw() to deal with the slots which have
completed due to internal abort.

The status codes have the following meaning:

- STAT_IO_ABORTED: the IO has been aborted due to internal abort,
  whether by device or individual abort command

- STAT_IO_COMPLETE: internal abort command has completed successfully
  for device or individual abort command

- STAT_IO_NO_DEVICE: internal abort command has completed for device but
  cannot find any IO

- STAT_IO_NOT_VALID: internal abort command has completed for single
  command but could not find the command
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add function to prepare the an internal abort for v2 hw.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Execute an internal abort for executing a task abort.
This is for case of the command still being present
in host when abort is executed.

For a SATA internal abort, we set abort for all tasks
associated with the device.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Execute an internal abort for that device when it is removed, so that
commands for that device are not processed.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add main code for internal abort functionality.

The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.

Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.

Two modes of internal abort are supported:

 - device
 - individual command

For device, when the internal abort is issued all commands in the host
for that device are aborted.  For a single command, only that command is
aborted if it is still in the host.

In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

req_table is allocate by kzalloc, so we don't need to zero it again.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We don't need to use kzalloc as we will always memset the
local_atto_ioctl later.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver version: 11.2.0.0
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change the copyright to:
Copyright © xxxx - 2016 Broadcom

Update email.ids:
@avagotech.com - @broadcom.com
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current EQ delay is set to 0 to receive very high max interrupt per sec.
Set EQ delay to 32 - reducing max interrupt rate from 65K to 20K per sec.

Set TCP connection window size to 64K with scale shift count 2.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In very rare scenario, connection gets killed after throwing this error:
scsi host0: BM_2312 : Event CXN_KILLED_BAD_WRB_INDEX_ERROR[15]... CID : 4
connection1:0: detected conn error (1011)

memset ISCSI_WRB descriptor to zero for all allocations of WRB handle.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

BUG: unable to handle kernel NULL pointer dereference at 000000000000015e
IP: [<ffffffffa0081700>]
hwi_get_async_handle.isra.23.constprop.39+0x90/0x1d0 [be2iscsi]
PGD 0
Oops: 0000 [#1] SMP
...
Call Trace:
 <IRQ>
 [<ffffffffa00818bc>] hwi_process_default_pdu_ring+0x7c/0x280 [be2iscsi]
 [<ffffffffa0088f51>] beiscsi_process_cq+0x321/0xb90 [be2iscsi]
 [<ffffffff810af028>] ? __wake_up_common+0x58/0x90
 [<ffffffff810b0d84>] ? __wake_up+0x44/0x50
 [<ffffffffa0089a2d>] be_iopoll+0x1d/0xb0 [be2iscsi]
 [<ffffffff812d1f61>] blk_iopoll_softirq+0xc1/0x100
 [<ffffffff81084b0f>] __do_softirq+0xef/0x280

The symptom observed is multiple async handles get queued for same index
thus causing leak in buffers posted to FW.

The root cause is:
- async handle is continued to be used even if it does not match the
completion.
- list_move operation done on already filled index.

1. Remove use of writables, host_write_ptr and ep_read_ptr.
2. Remove consumed logic to update writables. Instead, use only
free_entries to do the accounting of handles to be posted back.
3. Remove busy_list, instead use simple slot to index handles.
4. Added check no data, header less and overflow to make sure
all async_handles are flushed in error cases.
5. Added code to verify gathering of handles to form PDU by
checking final bit before forwarding PDU.
6. Added code to catch mismatch with CQE and handle gracefully.
7. Use AMAP, traverse cri_wait_queue list to post buffers, log
"async PDU" related errors.
8. Rearranged few data structures and added comments in init &
processing path.
9. Added WARN_ONs to catch any HD ring corruption.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver unload should call COMMON_FUNCTION_RESET. For TPE feature, this
ensures that FW has knowledge about driver getting unloaded and can
reset its bit vector.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Sessions are no longer valid, so schedule sess_work to fail the sessions
immediately when error is detected. This is done to avoid iSCSI transport
layer to keep sending NOP-Out which driver any ways fail.

Schedule sess_work immediately in case of HBA error. Old sessions are gone
for good and need to be re-established.

iscsi_session_failure needs process context hence this work.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After UE is detected, check for recoverable error by reading
SLIPORT SEMAPHORE register. If transient parity error i.e. 0xExxx
then schedule recovery work on driver wq.

FLag this error to prevent any transactions for the duration of ue2rp to
restart polling. After that, if FW becomes ready then recover port.

Wake up processes in wq before going offline.
Wait for process to execute before cleaning up.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

mgmt_epfw_cleanup does not implement v1 of OPCODE_COMMON_ISCSI_CLEANUP
IOCTL for SkyHawk.

Replace use of MCCQ with BMBX for issuing the IOCTL.
Remove be_mcc_compl_poll which is no longer needed.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

SLIPORT FUNCTION_RESET does not reset the chip.
So POST status needs to be checked before issuing FUNCTION_RESET.
The completion of FUNCTION_RESET is indicated in BMBX Rdy bit.

be_cmd_fw_initialize too needs to be done before issuing any cmd to FW.
be_cmd_fw_initialize is renamed as beiscsi_cmd_special_wrb.
Rearrange and rename few functions in init and cleanup path.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

beiscsi_fail_session is defined in be_cmds.c: move it to be_iscsi.c
Move card configuration commands to be_cmds.c.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

BE3 and SH cards can recover from transient parity errors treated
earlier as unrecoverable errors.

Add IOCTL to query FW support for this feature.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UE detection in health check is done in a work scheduled in global wq.
UE caused due to transient parity errors are recoverable and reported
within 1s. If this check for TPE gets delayed, PF0 might initiate
soft-reset and then status of UE recoverable is lost.

Handle UE detection in timer routine. Move out EQ delay update work
from health check. Make the IOCTL for EQ delay update non-blocking
as the completion status is ignored.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Boot work involves:
1. Find and fetch configured boot session and its handle.
2. Attempt to open the session if its not.
3. Get the session details for boot kset creation.
4. Logout of that session owned by FW.
5. Create boot kset for session details.

All these actions were done in blocking call with retries in global wq.
Other works in wq suffered if the IOCTLs stalled or timed out.

This change moves all the boot work to make it non-blocking.
The work queued in global wq just issues the IOCTL depending on the action
to be taken and mcc wq schedules work depending on status of the IOCTL.
Initial boot_work is started on link and ASYNC event.

The other code changes move all boot related functions in one place and
follow naming conventions.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Save ue_detected and fw_timeout errors in state field of beiscsi_hba.
BEISCSI_HBA_RUNNING
BEISCSI_HBA_LINK_UP
BEISCSI_HBA_BOOT_FOUND
BEISCSI_HBA_PCI_ERR
BEISCSI_HBA_FW_TIMEOUT
BEISCSI_HBA_IN_UE

Make sure no PCI transaction happens once in error state.
Add checks in IO path to detect HBA in error.

Skip hwi_purge_eq step which can't be done in error state.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>