- 11 2月, 2013 1 次提交
-
-
由 Ilan Peer 提交于
The FW scheduler, schedules the bindings over a session of 128 fragments (each is 4 TU long). The quota command should allocate all the session fragments between all the bindings that require quota allocation. Currently, use static allocation, where the fragments are equally distributed between all data bindings. Note, that not allocating all the session's fragments might cause the FW scheduler to leave the medium unused. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 05 2月, 2013 2 次提交
-
-
由 Johannes Berg 提交于
With new transports coming up, move to threaded interrupt handling now. This has the advantage that we can use the same locking scheme with all different transports we may need to implement. Note that the TX path obviously still runs in a tasklet, so some spin_lock() calls need to change to spin_lock_bh() calls to properly lock out the TX path. In my test on a Calpella platform this has no impact on throughput or latency. Also add lockdep annotations to avoid lockups due to catch sending synchronous commands or using locks that connect with them from the irq thread. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
This is not needed with MVM firmware. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 01 2月, 2013 4 次提交
-
-
由 Lilach Edelstein 提交于
Move the reg_lock that protects HW register access into the transport implementation. Locking is no longer exposed, but handled internally in grab and release NIC access. This simplifies the users. Signed-off-by: NLilach Edelstein <lilach.edelstein@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Lilach Edelstein 提交于
Express iwl_set_bit() and iwl_clear_bit() through iwl_set_bits_mask() and add the latter to the transport's API in order to allow different implementation for different transport types in the future. Signed-off-by: NLilach Edelstein <lilach.edelstein@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
As the rate scaling algorithm will attempt to enable aggregation over and over again, the message will flood the log if there is, for example, Bluetooth streaming music. Make it a debug messages instead of printing it all the time. Reported-by: NJan-Michael Brummer <jan.brummer@tabos.org> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Newer firmware revisions have a completely new firmware API. This is the new driver for this new API. I've listed the people who directly contributed code, but many others from various teams have contributed in other ways. Cc: Alexander Bondar <alexander.bondar@intel.com> Cc: Amit Beka <amit.beka@intel.com> Cc: Amnon Paz <amnonx.paz@intel.com> Cc: Assaf Krauss <assaf.krauss@intel.com> Cc: David Spinadel <david.spinadel@intel.com> Cc: Dor Shaish <dor.shaish@intel.com> Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Cc: Eytan Lifshitz <eytan.lifshitz@intel.com> Cc: Ilan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 31 1月, 2013 33 次提交
-
-
由 Johannes Berg 提交于
The new MVM (multi-virtual MAC) firmware driver requires NVM (non-volatile memory) parsing code and some PHY information database code. Add this separately. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
The firmware TLV for calibration data isn't really a u64, but two u32 values. Define a struct for that and change the parser. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Just format the enum better. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Add configuration and detection code for the new 7000 series, with 7260 and 3160 devices. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
-
由 Vladimir Kondratiev 提交于
In case vring setup with the firmware failed, success status was returned. fix it. Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Firmware crash on attempt to delete Rx chain. Driver part of Rx chain removed only in preparation for the target reset; as reset is the only flow that removes Rx chain in the firmware. Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Disable interrupts first to prevent spurious WMI events arrival Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
When connect times out, scan was not re-enabled. Strictly say, it is firmware issue - it should issue "disconnect" event but it does not. Compensate in the driver. Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Other parts of Rx path (BACK logic) will need to access associated data Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Due to multi-tx-queue design, wil_start_xmit() used to be executed concurrently for different queues. Then, these transmits delivered to the same queue, creating race. As result, Tx descriptor may be skipped, causing stall in hardware. Convert to single Tx queue fixes it. Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
This allows to account for Tx errors Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Move WMI related operations to wmi.c as helper functions Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Introduce debug category "MISC", convert all raw wil_dbg() to this category. This improves dynamic debug manageability Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
Make printings from IRQ appears in dmesg in chronological order Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Kondratiev 提交于
In the firmware, added is ability to report internal errors using IRQ. Catch this IRQ and notify user space via netlink User space get notified like (udevadm monitor --kernel --property): KERNEL[12660.320520] change /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net) ACTION=change DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 DEVTYPE=wlan EVENT=FW_ERROR IFINDEX=6 INTERFACE=wlan12 SEQNUM=2489 SOURCE=wil6210 SUBSYSTEM=net Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Cyril Roelandt 提交于
Check that the array indexes are in-bounds before accessing the rate2 and tmp arrays. Found with the following semantic patch: <smpl> @@ identifier t; identifier idx; expression E; statement S; @@ * for (... ; <+... t[idx] ...+> && idx < E ; ...) S </smpl> Signed-off-by: NCyril Roelandt <tipecaml@gmail.com> Acked-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Guenter Roeck 提交于
Fix: drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’: drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but not used [-Wunused-but-set-variable] seen when building allmodconfig on x86_64 with W=1 by removing the unused variable. Signed-off-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch is based on "iwlwifi: fix antenna bitmask". (362b0563) Like the new iwlagn devices, the old 4965N device only supports a maximum of three antennas. Hence only three bits are used, the fourth bit is likely the A-MPDU indicator. Cc: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
The old bcm47xx gpio code had support for gpio_to_irq, but the new code did not provide this function, but returned -ENXIO all the time. This patch adds the missing function. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
The old bcm47xx gpio code had support for gpio_to_irq, but the new code did not provide this function, but returned -ENXIO all the time. This patch adds the missing function. arch/mips/bcm47xx/wgt634u.c calls gpio_to_irq() and got the correct irq number with the old gpio handling code. With this patch the code in wgt634u.c should work again. I do not have a wgt634u to test this. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bing Zhao 提交于
Instead of converting it to a bogus error code -1, we should return the original error code from lower layer driver. This error code will be printed so it may give user some clues on what has happened. Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alexey Khoroshilov 提交于
If pci_iomap() fails in mwifiex_pcie_init(), it breaks off initialization, deallocates all resources, but returns zero. The patch adds -EIO as return value in this case. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Anatol Pomozov 提交于
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Yogesh Ashok Powar 提交于
While using STA mode in the AP firmware, avoid calling some firmware commands which are not supported by the AP firmware. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Yogesh Ashok Powar 提交于
Choose interface specific function calls based on interface type instead of firmware types. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Yogesh Ashok Powar 提交于
Add and delete self entry in the firmware sta database for AP interface only. We do not need such an entry for STA interface. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Yogesh Ashok Powar 提交于
Firmware supports hardware encryption feature for the station interface running on AP firmware. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Yogesh Ashok Powar 提交于
Set mac type for station interface on AP firmware as secondary. This allows the firmware to set specific characteristics for the STA interface. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-