Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 06 8月, 2015 3 次提交
  3. 05 8月, 2015 1 次提交
  5. 04 8月, 2015 4 次提交
  7. 25 7月, 2015 1 次提交
  9. 24 7月, 2015 1 次提交
  11. 19 7月, 2015 1 次提交
    • S
      hid-sensor: Fix suspend/resume delay · 88cc7b4e
      由 Srinivas Pandruvada 提交于 
      By default all the sensors are runtime suspended state (lowest power
state). During Linux suspend process, all the run time suspended
devices are resumed and then suspended. This caused all sensors to
power up and introduced delay in suspend time, when we introduced
runtime PM for HID sensors. The opposite process happens during resume
process.

To fix this, we do powerup process of the sensors only when the request
is issued from user (raw or tiggerred). In this way when runtime,
resume calls for powerup it will simply return as this will not match
user requested state.

Note this is a regression fix as the increase in suspend / resume
times can be substantial (report of 8 seconds on Len's laptop!)
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: NLen Brown <len.brown@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
      88cc7b4e
  13. 18 7月, 2015 6 次提交
  15. 16 7月, 2015 1 次提交
  17. 15 7月, 2015 3 次提交
    • D
      libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit · af34d637
      由 David Milburn 提交于 
      Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db6),
data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family)
SATA controller. This patch will allow the driver to limit max_sectors as before

 # cat /sys/block/sdb/queue/max_sectors_kb
 512

I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2
before seeing corruption, but seems safer to use previous limit. Without this
patch max_sectors_kb will be 32767.

tj: Minor comment update.
Reported-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.19 and later
Fixes: 34b48db6 ("block: remove artifical max_hw_sectors cap")
      af34d637
    • A
      libata: add ATA_HORKAGE_NOTRIM · 71d126fd
      由 Arne Fitzenreiter 提交于 
      Some devices lose data on TRIM whether queued or not.  This patch adds
a horkage to disable TRIM.

tj: Collapsed unnecessary if() nesting.
Signed-off-by: NArne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
      71d126fd
    • L
      efi: Handle memory error structures produced based on old versions of standard · 4c62360d
      由 Luck, Tony 提交于 
      The memory error record structure includes as its first field a
bitmask of which subsequent fields are valid. The allows new fields
to be added to the structure while keeping compatibility with older
software that parses these records. This mechanism was used between
versions 2.2 and 2.3 to add four new fields, growing the size of the
structure from 73 bytes to 80. But Linux just added all the new
fields so this test:
	if (gdata->error_data_length >= sizeof(*mem_err))
		cper_print_mem(newpfx, mem_err);
	else
		goto err_section_too_small;
now make Linux complain about old format records being too short.

Add a definition for the old format of the structure and use that
for the minimum size check. Pass the actual size to cper_print_mem()
so it can sanity check the validation_bits field to ensure that if
a BIOS using the old format sets bits as if it were new, we won't
access fields beyond the end of the structure.
Signed-off-by: NTony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
      4c62360d
  19. 13 7月, 2015 3 次提交
  21. 10 7月, 2015 5 次提交
    • P
      KVM: count number of assigned devices · 5544eb9b
      由 Paolo Bonzini 提交于 
      If there are no assigned devices, the guest PAT are not providing
any useful information and can be overridden to writeback; VMX
always does this because it has the "IPAT" bit in its extended
page table entries, but SVM does not have anything similar.
Hook into VFIO and legacy device assignment so that they
provide this information to KVM.
Reviewed-by: NAlex Williamson <alex.williamson@redhat.com>
Tested-by: NJoerg Roedel <jroedel@suse.de>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      5544eb9b
    • E
      cdc_ncm: Add support for moving NDP to end of NCM frame · 4a0e3e98
      由 Enrico Mioso 提交于 
      NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.

This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).

V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4a0e3e98
    • T
      blkcg: fix blkcg_policy_data allocation bug · 06b285bd
      由 Tejun Heo 提交于 
      e48453c3 ("block, cgroup: implement policy-specific per-blkcg
data") updated per-blkcg policy data to be dynamically allocated.
When a policy is registered, its policy data aren't created.  Instead,
when the policy is activated on a queue, the policy data are allocated
if there are blkg's (blkcg_gq's) which are attached to a given blkcg.
This is buggy.  Consider the following scenario.

1. A blkcg is created.  No blkg's attached yet.

2. The policy is registered.  No policy data is allocated.

3. The policy is activated on a queue.  As the above blkcg doesn't
   have any blkg's, it won't allocate the matching blkcg_policy_data.

4. An IO is issued from the blkcg and blkg is created and the blkcg
   still doesn't have the matching policy data allocated.

With cfq-iosched, this leads to an oops.

It also doesn't free policy data on policy unregistration assuming
that freeing of all policy data on blkcg destruction should take care
of it; however, this also is incorrect.

1. A blkcg has policy data.

2. The policy gets unregistered but the policy data remains.

3. Another policy gets registered on the same slot.

4. Later, the new policy tries to allocate policy data on the previous
   blkcg but the slot is already occupied and gets skipped.  The
   policy ends up operating on the policy data of the previous policy.

There's no reason to manage blkcg_policy_data lazily.  The reason we
do lazy allocation of blkg's is that the number of all possible blkg's
is the product of cgroups and block devices which can reach a
surprising level.  blkcg_policy_data is contrained by the number of
cgroups and shouldn't be a problem.

This patch makes blkcg_policy_data to be allocated for all existing
blkcg's on policy registration and freed on unregistration and removes
blkcg_policy_data handling from policy [de]activation paths.  This
makes that blkcg_policy_data are created and removed with the policy
they belong to and fixes the above described problems.
Signed-off-by: NTejun Heo <tj@kernel.org>
Fixes: e48453c3 ("block, cgroup: implement policy-specific per-blkcg data")
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
      06b285bd
    • T
      blkcg: implement all_blkcgs list · 7876f930
      由 Tejun Heo 提交于 
      Add all_blkcgs list goes through blkcg->all_blkcgs_node and is
protected by blkcg_pol_mutex.  This will be used to fix
blkcg_policy_data allocation bug.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
      7876f930
    • I
      libceph: enable ceph in a non-default network namespace · 757856d2
      由 Ilya Dryomov 提交于 
      Grab a reference on a network namespace of the 'rbd map' (in case of
rbd) or 'mount' (in case of ceph) process and use that to open sockets
instead of always using init_net and bailing if network namespace is
anything but init_net.  Be careful to not share struct ceph_client
instances between different namespaces and don't add any code in the
!CONFIG_NET_NS case.

This is based on a patch from Hong Zhiguo <zhiguohong@tencent.com>.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>
      757856d2
  23. 09 7月, 2015 1 次提交
  25. 08 7月, 2015 4 次提交
    • T
      hotplug: Prevent alloc/free of irq descriptors during cpu up/down · a8994181
      由 Thomas Gleixner 提交于 
      When a cpu goes up some architectures (e.g. x86) have to walk the irq
space to set up the vector space for the cpu. While this needs extra
protection at the architecture level we can avoid a few race
conditions by preventing the concurrent allocation/free of irq
descriptors and the associated data.

When a cpu goes down it moves the interrupts which are targeted to
this cpu away by reassigning the affinities. While this happens
interrupts can be allocated and freed, which opens a can of race
conditions in the code which reassignes the affinities because
interrupt descriptors might be freed underneath.

Example:

CPU1				CPU2
cpu_up/down
 irq_desc = irq_to_desc(irq);
				remove_from_radix_tree(desc);
 raw_spin_lock(&desc->lock);
				free(desc);

We could protect the irq descriptors with RCU, but that would require
a full tree change of all accesses to interrupt descriptors. But
fortunately these kind of race conditions are rather limited to a few
things like cpu hotplug. The normal setup/teardown is very well
serialized. So the simpler and obvious solution is:

Prevent allocation and freeing of interrupt descriptors accross cpu
hotplug.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: xiao jin <jin.xiao@intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Link: http://lkml.kernel.org/r/20150705171102.063519515@linutronix.de
      a8994181
    • S
      mtd: nand: Fix NAND_USE_BOUNCE_BUFFER flag conflict · 5f867db6
      由 Scott Wood 提交于 
      Commit 66507c7b ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer") added a flag NAND_USE_BOUNCE_BUFFER
using the same bit value as the existing NAND_BUSWIDTH_AUTO.

Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Fixes: 66507c7b ("mtd: nand: Add support to use nand_base
	poi databuf as bounce buffer")
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
      5f867db6
    • T
      tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build · 37b64a42
      由 Thomas Gleixner 提交于 
      Making tick_broadcast_oneshot_control() independent from
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST broke the build for
CONFIG_GENERIC_CLOCKEVENTS=n because the function is not defined
there.

Provide a proper stub inline.

Fixes: f32dd117 'tick/broadcast: Make idle check independent from mode and config'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
      37b64a42
    • T
      tick/broadcast: Make idle check independent from mode and config · f32dd117
      由 Thomas Gleixner 提交于 
      Currently the broadcast busy check, which prevents the idle code from
going into deep idle, works only in one shot mode.

If NOHZ and HIGHRES are off (config or command line) there is no
sanity check at all, so under certain conditions cpus are allowed to
go into deep idle, where the local timer stops, and are not woken up
again because there is no broadcast timer installed or a hrtimer based
broadcast device is not evaluated.

Move tick_broadcast_oneshot_control() into the common code and provide
proper subfunctions for the various config combinations.

The common check in tick_broadcast_oneshot_control() is for the C3STOP
misfeature flag of the local clock event device. If its not set, idle
can proceed. If set, further checks are necessary.

Provide checks for the trivial cases:

 - If broadcast is disabled in the config, then return busy

 - If oneshot mode (NOHZ/HIGHES) is disabled in the config, return
   busy if the broadcast device is hrtimer based.

 - If oneshot mode is enabled in the config call the original
   tick_broadcast_oneshot_control() function. That function needs
   extra checks which will be implemented in seperate patches.

[ Split out from a larger combo patch ]
Reported-and-tested-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Suzuki Poulose <Suzuki.Poulose@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Catalin Marinas <Catalin.Marinas@arm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1507070929360.3916@nanos
      f32dd117
  27. 07 7月, 2015 2 次提交
    • S
      ACPI / scan: Add support for ACPI _CLS device matching · 26095a01
      由 Suthikulpanit, Suravee 提交于 
      Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.

To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.

    acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
    # cat /sys/devices/platform/AMDI0600:00/modalias
    acpi:AMDI0600:010601:

where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code

Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.

    static const struct acpi_device_id ahci_acpi_match[] = {
        { ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
        {},
    };

In this case, the corresponded entry in modules.alias file would be:

    alias acpi*:010601:* ahci_platform
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      26095a01
    • R
      ACPI / PNP: Reserve ACPI resources at the fs_initcall_sync stage · 0294112e
      由 Rafael J. Wysocki 提交于 
      This effectively reverts the following three commits:

 7bc10388 ACPI / resources: free memory on error in add_region_before()
 0f1b414d ACPI / PNP: Avoid conflicting resource reservations
 b9a5e5e1 ACPI / init: Fix the ordering of acpi_reserve_resources()

(commit b9a5e5e1 introduced regressions some of which, but not
all, were addressed by commit 0f1b414d and commit 7bc10388
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.

The story is as follows.  First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes.  Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.

The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e1).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d.

That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook.  That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d wouldn't be
necessary any more.

For this reason, the changes made by commit 0f1b414d are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e1 that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: NRoland Dreier <roland@purestorage.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      0294112e
  29. 06 7月, 2015 1 次提交
    • P
      module: relocate module_init from init.h to module.h · 0fd972a7
      由 Paul Gortmaker 提交于 
      Modular users will always be users of init functionality, but
users of init functionality are not necessarily always modules.

Hence any functionality like module_init and module_exit would
be more at home in the module.h file.  And module.h should
explicitly include init.h to make the dependency clear.

We've already done all the legwork needed to ensure that this
move does not cause any build regressions due to implicit
header file include assumptions about where module_init lives.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
      0fd972a7
  31. 05 7月, 2015 2 次提交
  33. 04 7月, 2015 1 次提交