This patch adds support for the Cirrus Logic EDB9307, an evaluation
board based on the Cirrus Logic EP9307 SoC, which features amongst
other things 64M RAM, 32M NOR flash, 3 USB host ports, audio in/out,
two serial ports and a 10/100 ethernet interface.
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the IRQ numbers of the CF and SDI interface on the S3C2412
and S3C2413. Add support to handle these IRQs properly and
ensure that the SDI controller platform device is correctly
renumbered.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As a consequence registers are now accessed with __raw_{read,write}[bl].
Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Up to now only board-a9m9750dev.c used GPIOs.  It just wrote directly into the
corresponding registers.  Now it properly reserves the gpio and uses the API
function to configure it.
Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This implementation conforms to the general GPIO API
introduced in 2.6.21.

This patch was signed-of by David Brownell before I exported the functions
using EXPORT_SYMBOL.
Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The FPGA on the a9m9750dev board interrupts the CPU via EXT2. So
to acknowledge any FPGA interrupt IRQ_EXT2 must be acknowledged.
Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

... but the rtc-cmos is rather broken; if PNP is enabled, it assumes
that we have ACPI (!) which is quite bogus on these platforms -
which may have ISAPNP but not ACPI.  Something to be solved in the
future.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a magic number before the resume code so
that a bootloader can check that there is an
image to resume to.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The cpu_architecture() function in arch/arm/kernel/setup.c only works
with cores produced by ARM Ltd. The more generic approach is to read
the ID_MMFR0 register and check for the VMSA or PMSA version
supported. With this patch, the ARM11MPCore would be reported as ARMv7
since its MMU is compatible with ARMv7.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Starting with ARMv7-A, conditional execution of undefined instructions
can trigger an exception even if the condition check fails. This patch
modifies the NWFPE support to check the condition before emulating the
instruction.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes dead code.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

"extern inline" will have different semantics with gcc 4.3.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200.

 - Oneshot mode (used for NO_HZ and high res timers) uses the
   alarm to emulate a real oneshot timer; the trickiest bit is
   how to avoid some lowlevel races.  Thanks to Remy Bohmer for
   various fixes to this code.

 - Tighten up periodic mode support using the PIT.

 - Streamline reads of the 32KHz counter.  Thanks to Marc Pignat
   for some testing results: the CRTR register has *very* odd
   behavior.  The reread appears to work around stranger glitches
   than just getting an old clock value (which would quickly
   self-correct).

 - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100),
   since that no longer acts correct (time increases too fast).

Note that the at91sam9 and at91x40 chips need other solutions,
since they don't have the same system timer module.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NBill Gatliff <bgat@billgatliff.com>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes section mismatches related to DMA functions.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes section mismatches related to irq functions.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now the drivers are responsible to clear the irq in the respective
device, which seems to be the normal thing to do.

So the ack'ing of the timer irq moved to time.c.
Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Configuration support for the AT91x40 CPU and EB01 board.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Makefile build support for the Atmel AT91x40 CPU and EB01 board support.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the Atmel EB01 board (based on the Atmel AT91x40 CPU).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Prototypes for the at91x40 CPU support functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Interrupt setup support for the Atmel AT91x40 CPU family.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the timers in the Atmel AT91x40 family of CPUs.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Allow for configuration of the processor ID for the simplar non-MMU
ARM parts.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

Ensure nRSTOUT is not asserted during or on resume.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure that CPLD is restored to the original state
on resume, and that before going into suspend we
select the NAND bank we booted from for restarting.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the following (valid) section warnings:

WARNING: vmlinux.o(.text+0xf7b5c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bridge')
WARNING: vmlinux.o(.text+0xfc5f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_unmap_rom')
WARNING: vmlinux.o(.text+0xfc824): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0xfd6d8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd730): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd788): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd7e0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfe024): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
WARNING: vmlinux.o(.text+0xfe0f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
WARNING: vmlinux.o(.text+0xfe17c): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch enables to define MMC host get_ro() method through platform data.
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The EP93XX_GPIO_LINE_F() macro is supposed to be called with a line
number between 0 and 7, but the current code causes it to get called
with an spuriously offset number range {16..23}.
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NLennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The l2x0_inv_range() function doesn't handle unaligned addresses
correctly. It's necessary to clean the cache lines that are at the
start and end of the invalidate range, if the addresses are not aligned,
to prevent corruption of other data sharing the same cache line.
Signed-off-by: NRui Sousa <rui.p.m.sousa@gmail.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

vfp_init() takes care of the condition when CONFIG_VFP=y but no real VFP
device exists. However, when this condition is true, a compiler might
misplace code lines in a way that will break this support. (To be more
specific - fmrx(FPSID) might be executed before vfp_testing_entry
assignment, which will end up with Oops - undefined instruction).
This patch adds a barrier() to guarantee the right execution ordering.

Signed-off-by: Assaf Hoffman
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The second GIC asserts a permanent interrupt on Rev.B MPCore platforms.
Disable initialisation of this GIC to avoid unbootable systems.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

During GPIO testing on PiMX1 board there has been revealed
problem with some pins input functions. The GIUS bit has
to be set for inputs to work reliably too. It is surprising
that input worked on some inputs with incorrect setup before.
DR is not mandatory, but it ensures stable constant level
on internal traces.
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>
Acked-by: NJrgen Schindele <linux@schindele.name>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The pins for GPIO should be provided as plain number
build as (GPIO_PORTx + pin_number). But to setup
the output GPIO_GIUS and GPIO_DR have to be specified
in mode to route right value to the pin.

This is a fix, it should go to 2.6.23
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Enable serial idling and wakeup features
Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>