Utilize ethtool's callback `get_priv_flags' - shed more light on the
feasibility of devices as storage interfaces.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the standard DIV_ROUND_UP macro in order to provide better readability.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds checks at approprate places whether *dma_map*() call has
succeeded or not.
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Reviewed-by: NJay Fenlason <fenlason@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is about using rcu_dereference() when not in a rcu-locked section. It only
happens on initialization hence fix the initialization to not rcu_dereference()
Signed-off-by: NJay Fenlason <fenlason@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the SMSC911X driver may only be built for a specific set of
architectures, being limited to do so by a Kconfig depends line. This
means that if a platform wishes to use the driver, its architecture must
be added to the list explicitly, introducing pointless churn.

This may have been due to the driver's use of the {read,write}s{b,w,l}
functions, which have since been replaced with the more standard
io{read,write}{8,16,32}_rep. We can instead depend on HAS_IOMEM, which
should prevent build issues while allowing the driver to be built for
currently unlisted architectures, including x86 and arm64.

This patch removes the explicit list of architectures from the driver's
depend line, and replaces it with a dependency on HAS_IOMEM.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.

The name of the pci_driver struct had to be changed in order to prevent
a build failure.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.

The name of the pci_driver struct had to be changed in order to prevent
a build failure.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Acked-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the SW prio_tc values at initialization to the HW setting.
Setting the SW prio_tc default values to be the HW setting by reading the
rtrup2tc register. For any TC change we need to reset the device.
This will remove the need to reset the device at the first
time we call ixgbe_dcbnl_ieee_setets.
Signed-off-by: NAmir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes unused i2c function definition.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes LED issues with i210 and i211 devices, due to changes in the
device registers.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reorders disabling napi and irqs during igb_down.
This is done to avoid possible panic's found in other Intel drivers
when Rx traffic arrives while interface is going down.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where we were only checking to update checksum
on first part of nvm image.  Newer parts have multiple checksum fields and
checksum function will accommodate that as long as we call it in the first
place for any changes made.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This path allows users to get appropriate flow control setting on SerDes
devices, based on original implementation for Copper devices.
Also, since 100baseFX does not support setting flow control, so exclude
it from the setting mechanism.
Signed-off-by: NAkeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for SFP modules media type discovery for
SGMII, which will enable driver to detect supported external PHYs,
including 100baseFXSFP module.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to support a more accurate check for a PTP Rx hang where the
device can no longer timestamp received packets, we need to update, per
ring, when the last Rx timestamp was. Because of how the PTP Rx hang logic
works, the current logic is valid, but properly updating the ring variable
increases the accuracy of the check.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses the changes needed to make LEDs work properly with
negative logic. This implementation uses LED Invert bit to reverse the
logic issue that occurred when LEDs are driven by cathode. Keep LEDs
blinking for SerDes devices. Also made changes to magic number and the
for loop to reduce number of shifts.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issue of unlocking swflag_mutex for 82574 and 82583
devices regardless of if the hw semaphore has been successfully acquired via
e1000_get_hw_semaphore_82574(). With this patch, unlocking mutex now depends
on if the hw semaphore was successfully acquired before. And 82574/82583
devices are reset regardless of whether e1000_get_hw_semaphore_82574()
returns success or failure.
Reported-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver and Firmware versions updated to 3.2.21.1.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

User should not be allowed to delete base function of eth port. Add a new field
to the bfa ioc attributes structure to indicate if the given ioc is default
function on the port or not.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Failure of the UCAST set for base mac address fails when user configures a
duplicate mac address that matches that of another vNIC on the same port.
The bna does not handle the ucast failure and keeps this address in cache.
On disable of the vNIC, bna tries to delete the failed base mac address and the
fw asserts.

On failure of ucast address, mark ucast address set to false.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver configuration flags are retained across open/stop operations preventing
configurations to be set in next open/stop. Setting MTU on a 1020 causes
network to fail until a reboot is performed on the host.

Clear the flags when configuration resets in hardware.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds Device Tree support to dm9000 driver.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>