As there is a mx53_smd board in the kernel, using SMD_FEC_PHY_RST as the pin name can be misleading when used
on a MX53_EVK board.

Change the pin name to reflect the board name.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Current code inside mx53_evk_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value right after. This is not needed.

By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This iomux file contains all the available pins that are iomux
capable.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

add spi board information for spi nor device
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

add ecspi IOMUX setting, also fix a bug of chip select pin order
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

1. some macro definitions fix
2. add platform data for spi device
3. register spi clocks
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

1. changes some register address to fit macro definition
2. add platform data and clock for sdhc
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

add i2c platform data and clock
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

1. Adjust FEC base address name to fit macro definition
2. Add platform data and reset function for FEC
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

1. Add entries to Kconfig
2. Add machine definition
3. Add Uart platform data, pad setting and base address
4. Adjust GPIO irq number
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>