As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.

For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running.  So we now pass the
value of UTS_RELEASE to the firmware.  This adminq call is required per
the HAS document.  The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.

What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.

CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

A customer was chain-booting to provision his systems and one of the
steps was setting MFS. MFS isn't cleared by normal warm reboots
(clearing requires a GLOBR) and there was no indication of why Jumbo
Frame receives were failing.

Add a warning if MFS is set to anything lower than the default.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Detect and log information about pre-recovery mode when firmware
transitions to a recovery mode.
When a firmware transitions to a recovery mode it stores a number
of unexpected EMP resets in one of its registers. The number of EMP
resets ranging from 0x21 to 0x2A indicates that FW transitions
to recovery mode. Use these values to emit log entry about transition
process. Previously the pre-recovery mode may not have been detected
and there was no log entry when NIC was in pre-recovery mode.
Reviewed-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use jiffies to limit max waiting time for PF reset to succeed.
Previous wait loop was unreliable. It required unreasonably long time
to wait for PF reset after reboot when NIC was about to enter
recovery mode
Reviewed-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove all the unused defines as they are just dead weight.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move i40e_client.h to include/linux/net/intel/*
since its shared between i40iw and i40e.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rather than requiring every hw crypto capable NIC driver to do a check for
slave_dev being set, set real_dev in the xfrm layer and xso init time, and
then override it in the bonding driver as needed. Then NIC drivers can
always use real_dev, and at the same time, we eliminate the use of a
variable name that probably shouldn't have been used in the first place,
particularly given recent current events.

CC: Boris Pismenny <borisp@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
Suggested-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slave devices in a bond doing hardware encryption also need to be aware
that they're slaves, so we operate on the slave instead of the bonding
master to do the actual hardware encryption offload bits.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Acked-by: NJeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CONFIG_PM_SLEEP #ifdef checks in this file are inconsistent,
leading to a warning about sometimes unused function:

drivers/net/ethernet/intel/e1000e/netdev.c:137:13: error: unused function 'e1000e_check_me' [-Werror,-Wunused-function]

Rather than adding more #ifdefs, just remove them completely
and mark the PM functions as __maybe_unused to let the compiler
work it out on it own.

Fixes: e086ba2f ("e1000e: disable s0ix entry and exit flows for ME systems")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let PCI
core handle the work.

e1000_suspend() calls __e1000_shutdown() to perform intermediate tasks.
__e1000_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.

Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.
Signed-off-by: NVaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
 cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
 disabled

The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.

This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.

Fixes: bc7f75fa ("[E1000E]: New pci-express e1000 driver")
Reported-by: N"Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: NChen Yu <yu.c.chen@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 84af7a61 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

  a) 4 spaces + '---help---'
  b) 7 spaces + '---help---'
  c) 8 spaces + '---help---'
  d) 1 space + 1 tab + '---help---'
  e) 1 tab + '---help---'    (correct indentation)
  f) 1 tab + 1 space + '---help---'
  g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

  $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

With an increased number of VFs, it's possible to encounter the following
issue during reset.

    iavf b8d4:00:02.0: Hardware reset detected
    iavf b8d4:00:02.0: Reset never finished (0)
    iavf b8d4:00:02.0: Reset task did not complete, VF disabled

Increase the reset complete wait count to allow for 128 VFs to complete
reset.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 4ae4916b ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb
speeds") added the ability for the PF to report 2.5 and 5Gb speeds,
however, the iavf driver does not recognize those speeds as the values were
not added there. Add the proper enums and values so that iavf can properly
deal with those speeds.

Fixes: 4ae4916b ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb speeds")
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NWitold Fijalkowski <witoldx.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

adapter->link_speed has type enum virtchnl_link_speed but our comparisons
are against enum iavf_aq_link_speed. Though they are, currently, the same
values, change the comparison to the matching enum virtchnl_link_speed
since that may not always be the case.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Link speeds are communicated over virtchnl using an enum
virtchnl_link_speed. Currently, the highest link speed is 40Gbps which
leaves us unable to reflect some speeds that an ice VF is capable of.
This causes link speed to be misreported on the iavf driver.

Allow for communicating link speeds using Mbps so that the proper speed can
be reported for an ice VF. Moving away from the enum allows us to
communicate future speed changes without requiring a new enum to be added.

In order to support communicating link speeds over virtchnl in Mbps the
following functionality was added:
    - Added u32 link_speed_mbps in the iavf_adapter structure.
    - Added the macro ADV_LINK_SUPPORT(_a) to determine if the VF
      driver supports communicating link speeds in Mbps.
    - Added the function iavf_get_vpe_link_status() to fill the
      correct link_status in the event_data union based on the
      ADV_LINK_SUPPORT(_a) macro.
    - Added the function iavf_set_adapter_link_speed_from_vpe()
      to determine whether or not to fill the u32 link_speed_mbps or
      enum virtchnl_link_speed link_speed field in the iavf_adapter
      structure based on the ADV_LINK_SUPPORT(_a) macro.
    - Do not free vf_res in iavf_init_get_resources() as vf_res will be
      accessed in iavf_get_link_ksettings(); memset to 0 instead. This
      memory is subsequently freed in iavf_remove().

Fixes: 7c710869 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NSergey Nemov <sergey.nemov@intel.com>
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org

When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit ceb2f007 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.

Fixes: ceb2f007 ("ice: Use pci_get_dsn()")
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up

The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).

Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.

Fixes: 87324e74 ("ice: Implement ethtool ops for channels")
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the PF is modifying the VF's port VLAN on the fly when
configured via iproute. This is okay for most cases, but if the VF
already has guest VLANs configured the PF has to remove all of those
filters so only VLAN tagged traffic that matches the port VLAN will
pass. Instead of adding functionality to track which guest VLANs have
been added, just reset the VF each time port VLAN parameters are
modified.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To allow for resets during package download, increase the timeout period
after performing a PFR. The time waited is the global config lock
timeout plus the normal PFSWR timeout.
Signed-off-by: NDan Nowlin <dan.nowlin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".

An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.

Also, improve the comments surrounding this change.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Continuous Double "the" in a comment. Changed it to single "the"
Signed-off-by: NHari <harichandrakanthan@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Accordance to the i225 datasheet this register address
used by Host Transmit Discarded Packet by MAC counter
and not by not applicable Carrier Extension Error counter.
This patch comes to fix this wrong definition.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the following coccicheck warning:

drivers/net/ethernet/intel/i40e/i40e_adminq.c:699:13-21: Unneeded
variable: "ret_code". Return "0" on line 710
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.

Fix this by dropping the check for number of delay iterations.

While at it, also make __ew32_prepare() static as it's not used
anywhere else.

CC: stable <stable@vger.kernel.org>
Signed-off-by: NPunit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority
based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES
accordingly.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Acked-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The way Rx queue assignment based on mac address, Ethertype and VLAN
priority filtering operates in I225 doesn't allow us to properly support
NFC rules with multiple matches.

Consider the following example which assigns to queue 2 frames matching
the address MACADDR *and* Ethertype ETYPE.

$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2

When such rule is applied, we have 2 unwanted behaviors:

    1) Any frame matching MACADDR will be assigned to queue 2. It
       doesn't matter the ETYPE value.

    2) Any accepted frame that has Ethertype equals to ETYPE, no matter
       the mac address, will be assigned to queue 2 as well.

In current code, multiple-match filters are accepted by the driver, even
though it doesn't support them properly. This patch adds a check for
multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are
rejected.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>