Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This commit add check for return value of init_ring_common() in the
init_render_ring(). Now, when failure is detected the error code is
propagated to the caller instead of being ignored.
Signed-off-by: NKonrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.

Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.

But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.

To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).

Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.

v2: Lots of improvements

Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
  from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
  Suggested by Chris.

Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.

v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.

v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.

v5: Fixup locking around the fbcon set_to_gtt_domain call.

v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
  functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
  object. We already have precedence for fb_obj in the pin_and_fence
  functions.

v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
  directly. These functions center on the plane, the actual object is
  irrelevant - even a flip to the same object as already active should
  cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
  currently just calls intel_frontbuffer_flush since the implemenation
  differs.

This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.

Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.

v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.

v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.

v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
  in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
  still has work left to do before it's fully generic.

v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.

v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The downclocking checks a few more things, so not that simple to
convert. Also, this should get unified with the drrs handling and also
use the locking of that. Otoh the drrs locking is about as hapzardous
as no locking, at least on first sight.

For easier conversion ditch the upclocking on unload - we'll turn off
everything anyway.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should be taking the right power well refs these days, so this
shouldn't be necessary.  It also gets in the way of re-using these
routines for S0iX states, as those need all the power saving features
enabled.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't need to uninstall the full handler, simply disabling interrupts
ought to be enough.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

X could end up putting the fbcon fb into other domains, e.g.
for smooth take-overs. Also we want this for accurate frontbuffer
tracking: The set_config is an implicit flush and will re-enable
psr and similar features, so we need to bring the bo back into
the gtt domain.

v2: Add FIXME comment about fbcon locking fun in atomic context,
requested by Chris.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Can be useful to figure out imbalances and bugs in the frontbuffer
tracking.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So from just a quick look we seem to have enough information to
accurately figure out whether a given gem bo is used as a frontbuffer
and where exactly: We have obj->pin_count as a first check with no
false negatives and only negligible false positives. And then we can
just walk the modeset objects and figure out where exactly a buffer is
used as scanout.

Except that we can't due to locking order: If we already hold
dev->struct_mutex we can't acquire any modeset locks, so could
potential chase freed pointers and other evil stuff.

So we need something else. For that introduce a new set of bits
obj->frontbuffer_bits to track where a buffer object is used. That we
can then chase without grabbing any modeset locks.

Of course the consumers of this (DRRS, PSR, FBC, ...) still need to be
able to do their magic both when called from modeset and from gem
code. But that can be easily achieved by adding locks for these
specific subsystems which always nest within either kms or gem
locking.

This patch just adds the relevant update code to all places.

Note that if we ever support multi-planar scanout targets then we need
one frontbuffer tracking bit per attachment point that we expose to
userspace.

v2:
- Fix more oopsen. Oops.
- WARN if we leak obj->frontbuffer_bits when freeing a gem buffer. Fix
  the bugs this brought to light.
- s/update_frontbuffer_bits/update_fb_bits/. More consistent with the
  fb tracking functions (fb for gem object, frontbuffer for raw bits).
  And the function name was way too long.

v3: Size obj->frontbuffer_bits correctly so that all pipes fit in.

v4: Don't update fb bits in set_base on failure. Noticed by Chris.

v5: s/i915_gem_update_fb_bits/i915_gem_track_fb/ Also remove a few
local enum pipe variables which are now no longer needed to make the
function arguments no drop over the 80 char limit.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.

The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.

Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.

v2: Improve the commit message a bit.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.

The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.

If this breaks anything then we need to augment the enable/disable
functions accordingly.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not needed and further more will get in the way of a sane
locking scheme - psr_exit _can't_ take modeset locks due to lock
inversion, and at least once dp mst hits the connector list
is no longer static.

But since we track all state in dev_priv->psr there is no need
at all.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The original comment that introduced it said:

commit 0009e46c
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Fri Dec 6 14:11:02 2013 -0800

    drm/i915: Track which ring a context ran on

    Previously we dropped the association of a context to a ring. It is
    however very important to know which ring a context ran on (we could
    have reused the other member, but I was nitpicky).

    This is very important when we switch address spaces, which unlike
    context objects, do change per ring.

    As an example, if we have:

            RCS   BCS
    ctx            A
    ctx      A
    ctx      B
    ctx            B

    Without tracking the last ring B ran on, we wouldn't know to switch the
    address space on BCS in the last row.

But this is not really true, because we are already checking to != from (with
"from" being = ring->last_context) and that should be enough to make sure we
switch to the right address space.

We would have a problem if we switched the context object for every ring (since
then we would fail to do it in some situations) but we only switch it for the
render ring, so we don't care.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Jesse's SOix work required some patches from acpi-next, so pull it in
through a topic barnch.

Conflicts:
	drivers/gpu/drm/i915/i915_drv.c
	drivers/gpu/drm/i915/intel_pm.c
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise, we might receive a new interrupt before we have time to
ack the first one, eventually missing it.

Without an atomic XCHG operation with mmio space, this patch merely
reduces the window in which we can miss an interrupt (especially when
you consider how heavyweight the I915_READ/I915_WRITE operations are).

Notice that, before clearing a port-sourced interrupt in the IIR, the
corresponding interrupt source status in the PORT_HOTPLUG_STAT must be
cleared.

Spotted by Bob Beckett <robert.beckett@intel.com>.

v2:
- Add warning to commit message and comments to the code as per Chris
  Wilson's request.
- Imre Deak pointed out that the pipe underrun flag might not be signaled
  in IIR, so do not make valleyview_pipestat_irq_handler depend on it.

v3: Improve the source code comment.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise, we might receive a new interrupt before we have time to
ack the first one, eventually missing it.

The right order should be:

1 - Disable Master Interrupt Control.
2 - Find the category of interrupt that is pending.
3 - Find the source(s) of the interrupt and clear the Interrupt Identity bits (IIR)
4 - Process the interrupt(s) that had bits set in the IIRs.
5 - Re-enable Master Interrupt Control.

Without an atomic XCHG operation with mmio space, the above merely reduces the window
in which we can miss an interrupt (especially when you consider how heavyweight the
I915_READ/I915_WRITE operations are).

Spotted by Bob Beckett <robert.beckett@intel.com>.

v2: Add warning to commit message and comments to the code as per Chris Wilson's request.

v3: Improve the source code comment.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise, we might receive a new interrupt before we have time to
ack the first one, eventually missing it.

Without an atomic XCHG operation with mmio space, this patch merely
reduces the window in which we can miss an interrupt (especially when
you consider how heavyweight the I915_READ/I915_WRITE operations are).

Notice that, before clearing a port-sourced interrupt in the IIR, the
corresponding interrupt source status in the PORT_HOTPLUG_STAT must be
cleared.

Spotted by Bob Beckett <robert.beckett@intel.com>.

v2:
- Reorder the IIR clearing to reduce the window even further.
- Add warning to commit message and comments to the code as per Chris
  Wilson's request.
- Imre Deak pointed out that the pipe underrun flag might not be signaled
  in IIR, so do not make valleyview_pipestat_irq_handler depend on it.

v3: Improve the source code comment.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise, we might receive a new interrupt before we have time to ack the first
one, eventually missing it.

According to BSPec, the right order should be:

1 - Disable Master Interrupt Control.
2 - Find the source(s) of the interrupt.
3 - Clear the Interrupt Identity bits (IIR).
4 - Process the interrupt(s) that had bits set in the IIRs.
5 - Re-enable Master Interrupt Control.

Without an atomic XCHG operation with mmio space, the above merely reduces the window
in which we can miss an interrupt (especially when you consider how heavyweight the
I915_READ/I915_WRITE operations are).

We maintain the "disable SDE interrupts when handling" hack since apparently it works.

Spotted by Bob Beckett <robert.beckett@intel.com>.

v2: Add warning to commit message and comments to the code as per Chris Wilson's request.
v3: Improve the source comments.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A WARN_ON is perfectly fine.

The BUG in here seems to be the cause behind hard-hangs when I cat the
i915_gem_pageflip debugfs file (which calls this from an irq
spinlock). But only while running a full igt run after a while. I
still need to root cause the underlying issue.

I'll also start reject patches which add new BUG_ON but don't come
with a really good justification for it. The general rule really
should be to just WARN and hope the driver survives for long enough.

v2: Make the WARN a bit more useful per Chris' suggestion.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We could walk of a bad list otherwise when someone concurrently
unbinds stuff for fun.

I've suspected this as the root-cause behind seemingly inconsistent
state, but alas it's not.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Beignet needs these in order to program the L3 cache config for
OpenCL workloads, particularly when using SLM.
Signed-off-by: NBrad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Take the minimum of the object size and the vma size and prefault
only that much. Avoids a SIGBUS when mmapping only a portion of the
object.

Prefaulting was introduced here:
 commit b90b91d8
 Author: Chris Wilson <chris@chris-wilson.co.uk>
 Date:   Tue Jun 10 12:14:40 2014 +0100

    drm/i915: Prefault the entire object on first page fault

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Testcase: igt/gem_mmap/short-mmap
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables the framework for using MMIO based flip calls,
in contrast with the CS based flip calls which are being used currently.

MMIO based flip calls can be enabled on architectures where
Render and Blitter engines reside in different power wells. The
decision to use MMIO flips can be made based on workloads to give
100% residency for Media power well.

v2: The MMIO flips now use the interrupt driven mechanism for issuing the
flips when target seqno is reached. (Incorporating Ville's idea)

v3: Rebasing on latest code. Code restructuring after incorporating
Damien's comments

v4: Addressing Ville's review comments
    -general cleanup
    -updating only base addr instead of calling update_primary_plane
    -extending patch for gen5+ platforms

v5: Addressed Ville's review comments
    -Making mmio flip vs cs flip selection based on module parameter
    -Adding check for DRIVER_MODESET feature in notify_ring before calling
     notify mmio flip.
    -Other changes mostly in function arguments

v6: -Having a seperate function to check condition for using mmio flips (Ville)
    -propogating error code from i915_gem_check_olr (Ville)

v7: -Adding __must_check with i915_gem_check_olr (Chris)
    -Renaming mmio_flip_data to mmio_flip (Chris)
    -Rebasing on latest nightly

v8: -Rebasing on latest code
    -squash 3rd patch in series(mmio setbase vs page flip race) with this patch
    -Added new tiling mode update in intel_do_mmio_flip (Chris)

v9: -check for obj->last_write_seqno being 0 instead of obj->ring being NULL in
intel_postpone_flip, as this is a more restrictive condition (Chris)

v10: -Applied Chris's suggestions for squashing patches 2,3 into this patch.
These patches make the selection of CS vs MMIO flip at the page flip time, and
make the module parameter for using mmio flips as tristate, the states being
'force CS flips', 'force mmio flips', 'driver discretion'.
Changed the logic for driver discretion (Chris)

v11: Minor code cleanup(better readability, fixing whitespace errors, using
lockdep to check mutex locked status in postpone_flip, removal of __must_check
in function definition) (Chris)
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NSourab Gupta <sourab.gupta@intel.com>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # snb, ivb
[danvet: Fix up parameter alignement checkpatch spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Staring from HSW, the resolution limit of FBC has increased to
4096*4096

Issue: VIZ-2813
Change-Id: I842f64e3cf2c0d18d29ef1bcfef3b9bb1f1764ac
Signed-off-by: NDaisy Sun <daisy.sun@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds support for a write-enable bit in the entry of GTT.
This is handled via a read-only flag in the GEM buffer object which
is then used to see how to set the bit when writing the GTT entries.
Currently by default the Batch buffer & Ring buffers are marked as read only.

v2: Moved the pte override code for read-only bit to 'byt_pte_encode'. (Chris)
    Fixed the issue of leaving 'gt_old_ro' as unused. (Chris)

v3: Removed the 'gt_old_ro' field, now setting RO bit only for Ring Buffers(Daniel).

v4: Added a new 'flags' parameter to all the pte(gen6) encode & insert_entries functions,
    in lieu of overloading the cache_level enum (Daniel).

v5: Removed the superfluous VLV check & changed the definition location of PTE_READ_ONLY flag (Imre)
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that the primary plane can be disabled independently of the CRTC,
the debugfs code needs to be updated to recognize when the primary plane
is disabled and not try to return information about the primary plane's
framebuffer.

This change prevents a NULL dereference when reading i915_display_info
with a disabled primary plane.

v2: Replace a seq_printf() with seq_puts() (suggested by Damien)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Spotted while crawling around in the area.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Any comment containing "current Intel hardware supports" quickly
becomes obsolete, so remove it and let people discover the information
by looking at the function implementation.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Two BSpec updates changed the recommended values for BDW eDP and DP
DDI buffer translations. Now the signal levels also match the HSW signal
levels, which simplify things a little bit.

It seems some DP sinks don't work properly without voltage level 0 and
pre-emphasis level 3, so this patch may fix some bugs on
panels/monitors that happen on BDW but not on HSW.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rewrite i915_gem_render_state.c for the purposes of clarity and
compactness, in the process we can eliminate some dodgy math that did
not handle 64bit addresses correctly.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

An object can only have an active gtt mapping if it is currently bound
into the global gtt. Therefore we can simply walk the list of all bound
objects and check the flag upon those for an active gtt mapping.

From commit 48018a57
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Dec 13 15:22:31 2013 -0200

    drm/i915: release the GTT mmaps when going into D3

Also note that the WARN is inappropriate for this function as GPU
activity is orthogonal to GTT mmap status. Rather it is the caller that
relies upon this condition and so it should assert that the GPU is idle
itself.

References: https://bugs.freedesktop.org/show_bug.cgi?id=80081Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_dsi_init() bails out without freeing the memory 'intel_dsi' and
'intel_connector' point to. Simply bail out before allocating memory.

Picked up by Coverity - CID 1222750.
Signed-off-by: NChristoph Jaeger <christophjaeger@linux.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now we have the active/inactive state for exit and this actually changes the
HW enable bit the status was a bit confusing for users. So let's provide
more info.
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.

However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.

Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.

The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.

v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Early revs didn't have PPGTT support, so disable there.

v2: add debug msg when disabling on early stepping
v3: enable on other B3 packages as well (untested) (Ville)

References: https://bugs.freedesktop.org/show_bug.cgi?id=79669
References: https://bugs.freedesktop.org/show_bug.cgi?id=79670Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHECK   linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c
linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c:1529:47: warning: incorrect type in initializer (different address spaces)
linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c:1529:47:    expected struct drm_i915_gem_exec_object2 *user_exec_list
linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c:1529:47:    got void [noderef] <asn:1>*
linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c:1533:61: warning: incorrect type in argument 1 (different address spaces)
linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c:1533:61:    expected void [noderef] <asn:1>*dst
linux/drivers/gpu/drm/i915/i915_gem_execbuffer.c:1533:61:    got unsigned long long *<noident>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Knowing the device stepping may be crucial in analyzing problems. Since
we always ask bug reporters for dmegs with drm.debug=0xe (or something)
it would be nice if the PCI revision is already included in the dump.
Avoids having to ask for lspci output as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

obj->framebuffer_references isn't an atomic_t so the decrement needs to
be protected by some lock. struct_mutex seems like the appropriate lock
here, and we may already take it for the obj unref anyway.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On the current structure HSW doesn't support PSR with sprites enabled
but sprites can be enabled after PSR was enabled what would cause
user to miss screen updates.

v2: move it to update_plane.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>