- 20 8月, 2006 1 次提交
-
-
由 Andrew Morton 提交于
drivers/net/sundance.c:110: error: version causes a section type conflict I don't understand this error. It's referred to from both __init and __devinit code. With CONFIG_HOTPLUG=n, version[] is placed in .init.data and is referred to from .init.text. Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 06 7月, 2006 2 次提交
-
-
由 Jeff Garzik 提交于
- fealnx: convert #define to enum - fealnx, sundance: mark chip info table __devinitdata - fealnx: use dev_printk() during probe - fealnx: formatting cleanups - starfire: remove obsolete comment - sundance, via-rhine: add some whitespace where useful, in tables - sundance: prefer "{ }" table terminator - via-rhine: mark PCI probe table const Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Jeff Garzik 提交于
When in-kernel net drivers branched from Donald Becker's vanilla driver set, in the days before BitKeeper and git, a driver changelog was maintained in the driver source code. These days, the kernel's changelog is far superior and much more accurate, so the in-driver changelogs are removed. Another relic of the Becker/kernel split was version numbering, using "foo-LKx.y.z" notation, resulting in weird version numbers like "1.17b-LK1.1.9". These drivers are for older hardware, and see few changes these days, so the version numbers were all bumped to something more simple. Finally, in xircom_tulip_cb specifically, an additional cleanup removes the always-enabled CARDBUS cpp macro. Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 03 7月, 2006 1 次提交
-
-
由 Thomas Gleixner 提交于
Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 16 6月, 2006 1 次提交
-
-
Patch provided by Pedro Alejandro López-Valencia in http://bugzilla.kernel.org/show_bug.cgi?id=6691 The patch is derived from IC+ GPL'ed rework of sundance driver available at http://www.icplus.com.tw/pp-IP100A.html Patch closes http://bugzilla.kernel.org/show_bug.cgi?id=5858 as well. Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com> Cc: Pedro Alejandro López-Valencia <palopezv@gmail.com>
-
- 04 3月, 2006 1 次提交
-
-
由 Arjan van de Ven 提交于
-
- 27 1月, 2006 1 次提交
-
-
由 Arnaldo Carvalho de Melo 提交于
Make phy 0 actually be read, as it is not being right now as we have: int mii_status = mdio_read(dev, phy, MII_BMSR); int phyx = phy & 0x1f; When we should have instead: int phyx = phy & 0x1f; int mii_status = mdio_read(dev, phyx, MII_BMSR); so that when phy, in the end of the (phy = 1; phy <= 32...) loop gets to 32 phyx gets to 0, i.e. we were reading at 32, when the intended read was for 0. Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 29 10月, 2005 1 次提交
-
-
由 Philippe De Muyter 提交于
Under heavy PCI bus load, ports of the DFE-580TX 4-ethernet port board stop working, with currently no other cure than a powercycle. Here is a tested fix. By the way, I also fixed some references and attribution. Signed-off-by: NPhilippe De Muyter <phdm@macqel.be> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 20 10月, 2005 1 次提交
-
-
由 John W. Linville 提交于
Include MII address 0 at the end of the PHY scan. This covers the entire range of possible MII addresses. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 19 10月, 2005 2 次提交
-
-
由 John W. Linville 提交于
Expand the mask used when reseting the chip to include the GlobalReset bit. This fix comes from ICPlus and seems to be required for some cards. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 John W. Linville 提交于
Remove an if (1) { ... } block in sundance_probe1. Its purpose seems to be only to allow for delaring some extra local variables. But, it also adds ugly indentation without adding any meaning to the code. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 14 9月, 2005 1 次提交
-
-
由 John W. Linville 提交于
Add support for ETHTOOL_GPERMADDR to sundance. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 29 6月, 2005 1 次提交
-
-
由 David S. Miller 提交于
Many drivers use skb->tail unnecessarily. In these situations, the code roughly looks like: dev = dev_alloc_skb(...); [optional] skb_reserve(skb, ...); ... skb->tail ... But even if the skb_reserve() happens, skb->data equals skb->tail. So it doesn't make any sense to use anything other than skb->data in these cases. Another case was the s2io.c driver directly mucking with the skb->data and skb->tail pointers. It really just wanted to do an skb_reserve(), so that's what the code was changed to do instead. Another reason I'm making this change as it allows some SKB cleanups I have planned simpler to merge. In those cleanups, skb->head, skb->tail, and skb->end pointers are removed, and replaced with skb->head_room and skb->tail_room integers. Signed-off-by: NDavid S. Miller <davem@davemloft.net> Acked-by: NJeff Garzik <jgarzik@pobox.com>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-