- 09 2月, 2023 8 次提交
-
-
由 Bjorn Andersson 提交于
The three DMA memory regions allocated for the host memory space are documented to require alignment of 128, 1024, and 1024 respectively, but the returned address is checked for PAGE_SIZE alignment. In the case where these allocations are serviced by e.g. the Arm SMMU, the size and alignment will be determined by its supported page sizes. In most cases SZ_4K and a few larger sizes are available. In the typical configuration this does not cause problems, but in the event that the system PAGE_SIZE is increased beyond 4k, it's no longer reasonable to expect that the allocation will be PAGE_SIZE aligned. Limit the DMA alignment check to the actual alignment requirements written in the comments in the code, to avoid the UFS core refusing to initialize with such configuration. Link: https://lore.kernel.org/r/20230201034917.1902330-1-quic_bjorande@quicinc.comSigned-off-by: NBjorn Andersson <quic_bjorande@quicinc.com> Reviewed-by: NManivannan Sadhasivam <mani@kernel.org> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NAsutosh Das <quic_asutoshd@quicinc.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Randy Dunlap 提交于
Correct spelling problems for Documentation/scsi/ as reported by codespell. Link: https://lore.kernel.org/r/20230129231053.20863-8-rdunlap@infradead.orgSigned-off-by: NRandy Dunlap <rdunlap@infradead.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: linux-doc@vger.kernel.org Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Randy Dunlap 提交于
Correct spelling problems for Documentation/scsi/ ChangeLogs as reported by codespell. Link: https://lore.kernel.org/r/20230129231053.20863-7-rdunlap@infradead.orgSigned-off-by: NRandy Dunlap <rdunlap@infradead.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: linux-doc@vger.kernel.org Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Randy Dunlap 提交于
Correct spelling problems for Documentation/target/ as reported by codespell. Link: https://lore.kernel.org/r/20230127064005.1558-29-rdunlap@infradead.orgSigned-off-by: NRandy Dunlap <rdunlap@infradead.org> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Cc: target-devel@vger.kernel.org Cc: Jonathan Corbet <corbet@lwn.net> Cc: linux-doc@vger.kernel.org Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Kees Cook 提交于
The aac_priv() helper assumes that the private cmd area immediately follows struct scsi_cmnd. Allocate this space as part of scsicmd, else there is a risk of heap overflow. Seen with GCC 13: ../drivers/scsi/aacraid/aachba.c: In function 'aac_probe_container': ../drivers/scsi/aacraid/aachba.c:841:26: warning: array subscript 16 is outside array bounds of 'void[392]' [-Warray-bounds=] 841 | status = cmd_priv->status; | ^~ In file included from ../include/linux/resource_ext.h:11, from ../include/linux/pci.h:40, from ../drivers/scsi/aacraid/aachba.c:22: In function 'kmalloc', inlined from 'kzalloc' at ../include/linux/slab.h:720:9, inlined from 'aac_probe_container' at ../drivers/scsi/aacraid/aachba.c:821:30: ../include/linux/slab.h:580:24: note: at offset 392 into object of size 392 allocated by 'kmalloc_trace' 580 | return kmalloc_trace( | ^~~~~~~~~~~~~~ 581 | kmalloc_caches[kmalloc_type(flags)][index], | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 582 | flags, size); | ~~~~~~~~~~~~ Fixes: 76a3451b ("scsi: aacraid: Move the SCSI pointer to private command data") Link: https://lore.kernel.org/r/20230128000409.never.976-kees@kernel.org Cc: Bart Van Assche <bvanassche@acm.org> Cc: Hannes Reinecke <hare@suse.de> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: NKees Cook <keescook@chromium.org> Reviewed-by: NVegard Nossum <vegard.nossum@oracle.com> Reviewed-by: NHannes Reinecke <hare@suse.de> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Martin K. Petersen 提交于
Abel Vesa <abel.vesa@linaro.org> says: This patchset adds UFS HC support for the new Qualcomm SM8550 SoC. Link: https://lore.kernel.org/r/20230119151406.4168685-1-abel.vesa@linaro.orgSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Abel Vesa 提交于
Document the compatible string for the UFS found on SM8550. Signed-off-by: NAbel Vesa <abel.vesa@linaro.org> Reviewed-by: NKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: NManivannan Sadhasivam <mani@kernel.org> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Abel Vesa 提交于
On SM8550, depending on the Qunipro, we can run with G5 or G4. For now, when the major version is 5 or above, we go with G5. Therefore, we need to specifically tell UFS HC that. Signed-off-by: NAbel Vesa <abel.vesa@linaro.org> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
- 04 2月, 2023 1 次提交
-
-
由 Arnd Bergmann 提交于
The newly added MSI support is mostly hidden inside of an #ifdef, except for one line that now causes a build failure when MSI is disabled: drivers/ufs/host/ufs-qcom.c: In function 'ufs_qcom_remove': drivers/ufs/host/ufs-qcom.c:1698:9: error: implicit declaration of function 'platform_msi_domain_free_irqs' [-Werror=i] 1698 | platform_msi_domain_free_irqs(hba->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Above that, the symbol that guards the other call was recently removed, so that is all dead code at the moment. Remove the incorrect #ifdef and instead of a Kconfig dependency to only allow building the driver when CONFIG_GENERIC_MSI_IRQ is enabled. This symbol is always present when PCI_MSI or ARM_GIC_V3_ITS are enabled, both of which should be present on kernels that can run on Qualcomm SoCs. The 'select RESET_CONTROLLER' in combination with this dependency unfortunately causes a dependency loop and this is a user-visible symbol, so it's better to change both to 'depends on'. Link: https://lore.kernel.org/r/20230126211831.2274211-1-arnd@kernel.org Fixes: 519b6274 ("scsi: ufs: qcom: Add MCQ ESI config vendor specific ops") Fixes: 13e7accb ("genirq: Get rid of GENERIC_MSI_IRQ_DOMAIN") Signed-off-by: NArnd Bergmann <arnd@arndb.de> Reviewed-by: NManivannan Sadhasivam <mani@kernel.org> Acked-by: NCan Guo <quic_cang@quicinc.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
- 24 1月, 2023 7 次提交
-
-
由 Martin K. Petersen 提交于
Bart Van Assche <bvanassche@acm.org> says: The third patch in this series enables DMA clustering in the UFS driver since UFS host controllers support DMA clustering. The first two patches fix bugs in the Exynos host controller driver. Link: https://lore.kernel.org/r/20230112234215.2630817-1-bvanassche@acm.orgSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Bart Van Assche 提交于
All UFS host controllers support DMA clustering. Hence enable DMA clustering. Notes: - The max_segment_size parameter implements the 256 KiB limit for the PRDT. The dma_boundary parameter represents a boundary that must not be crossed by DMA scatter/gather lists. I'm not aware of any restrictions on DMA scatter/gather lists in the UFSHCI specification other than the 256 KiB limit for the PRDT and the 32-bit address restriction for controllers that only support 32-bits DMA. The latter restriction is already handled by ufshcd_set_dma_mask(). - Without patch "scsi: ufs: exynos: Fix the maximum segment size", this patch breaks support for the Exynos controller. The history of the dma_boundary parameter in the UFS driver is as follows: * The initial UFS driver did not set the dma_boundary parameter. * Commit 4dd4130a ("scsi: make sure all drivers set the use_clustering flag") set the .use_clustering flag. * Commit 4af14d11 ("scsi: remove the use_clustering flag") removed the use_clustering flag and set the dma_boundary parameter instead. Cc: Avri Altman <avri.altman@wdc.com> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by: NBart Van Assche <bvanassche@acm.org> Acked-by: NAdrian Hunter <adrian.hunter@intel.com> Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Bart Van Assche 提交于
Prepare for enabling DMA clustering and also for supporting PAGE_SIZE != 4096 by declaring explicitly that the maximum segment size is 4096 bytes for Exynos UFS host controllers. Add this code in exynos_ufs_hce_enable_notify() such that it happens after scsi_host_alloc() and before __scsi_init_queue() is called by the LUN scanning code. Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Bart Van Assche 提交于
The Exynos UFS controller only supports scatter/gather list elements that are aligned on a 4 KiB boundary. Fix DMA alignment in case PAGE_SIZE != 4096. Rename UFSHCD_QUIRK_ALIGN_SG_WITH_PAGE_SIZE into UFSHCD_QUIRK_4KB_DMA_ALIGNMENT. Cc: Kiwoong Kim <kwmad.kim@samsung.com> Fixes: 2b2bfc8a ("scsi: ufs: Introduce a quirk to allow only page-aligned sg entries") Signed-off-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Deepak R Varma 提交于
A logical evaluation of type (!A || A && B) can be simplified as (!A || B). Improvement by suggested by excluded_middle.cocci Coccinelel semantic patch. Link: https://lore.kernel.org/r/Y7+oJuah0MgEW0PQ@ubun2204.myguest.virtualbox.orgSigned-off-by: NDeepak R Varma <drv@mailo.com> Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Deepak R Varma 提交于
Use a variable to compute memory size to be allocated once instead of repeatedly computing it at different locations in the function. Issue identified using the array_size_dup Coccinelle semantic patch. Link: https://lore.kernel.org/r/Y7spwF8HTt0c0l7y@ubun2204.myguest.virtualbox.orgSigned-off-by: NDeepak R Varma <drv@mailo.com> Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Randy Dunlap 提交于
Don't use "/**" to begin non-kernel-doc comments. Prevent a kernel-doc warning: drivers/scsi/elx/libefc_sli/sli4.c:13: warning: cannot understand function prototype: 'struct sli4_asic_entry_t sli4_asic_table[] = ' Signed-off-by: NRandy Dunlap <rdunlap@infradead.org> Cc: James Smart <james.smart@broadcom.com> Cc: Ram Vegesna <ram.vegesna@broadcom.com> Cc: target-devel@vger.kernel.org Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20230117070151.29339-1-rdunlap@infradead.orgSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
- 19 1月, 2023 12 次提交
-
-
由 Johan Hovold 提交于
UFS controllers may be cache coherent and must be marked as such in the devicetree to avoid data corruption. This is specifically needed on recent Qualcomm platforms like SC8280XP. Reviewed-by: NRob Herring <robh@kernel.org> Reviewed-by: NBjorn Andersson <andersson@kernel.org> Signed-off-by: NJohan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230116164236.18958-1-johan+linaro@kernel.orgSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Tom Rix 提交于
Smatch reports: drivers/scsi/qla2xxx/qla_mid.c:1189:6: warning: symbol 'qla_trim_buf' was not declared. Should it be static? drivers/scsi/qla2xxx/qla_mid.c:1221:6: warning: symbol '__qla_adjust_buf' was not declared. Should it be static? These functions are only used in qla_mid.c, so they should be static. Fixes: 1f8f9c34 ("scsi: qla2xxx: edif: Reduce memory usage during low I/O") Signed-off-by: NTom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/20230114013724.3943580-1-trix@redhat.comSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Fabio M. De Francesco 提交于
The use of kmap() is deprecated in favor of kmap_local_page(). There are two main problems with kmap(): (1) It comes with an overhead as the mapping space is restricted and protected by a global lock for synchronization and (2) it also requires global TLB invalidation when the kmap’s pool wraps and it might block when the mapping space is fully utilized until a slot becomes available. With kmap_local_page() the mappings are per thread, CPU local, can take page faults, and can be called from any context (including interrupts). It is faster than kmap() in kernels with HIGHMEM enabled. Furthermore, the tasks can be preempted and, when they are scheduled to run again, the kernel virtual addresses are restored and still valid. Therefore, replace kmap() with kmap_local_page() in ipr_copy_ucode_buffer() and, instead of open-coding local mappings + memcpy() + local un-mappings, use the better suited memcpy_to_page() helper. Suggested-by: NIra Weiny <ira.weiny@intel.com> Signed-off-by: NFabio M. De Francesco <fmdefrancesco@gmail.com> Link: https://lore.kernel.org/r/20230103182556.29080-1-fmdefrancesco@gmail.comSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Fabio M. De Francesco 提交于
kmap_atomic() is deprecated in favor of kmap_local_page(). Therefore, replace kmap_atomic() with kmap_local_page() in ips_is_passthru(). In the meantime remove an unnecessary comment, align code, and remove spaces. kmap_atomic() is implemented like a kmap_local_page() which also disables page-faults and preemption (the latter only for !PREEMPT_RT kernels). The code within the mapping/unmapping in ips_is_passthru() is already in atomic context because of a call to local_irq_save() and kmap_local_page() can be called in atomic context too (including interrupts). Therefore, a mere replacement of the old API with the new one is all it is required (i.e., there is no need to explicitly add any calls to pagefault_disable() and/or preempt_disable()). Suggested-by: NIra Weiny <ira.weiny@intel.com> Signed-off-by: NFabio M. De Francesco <fmdefrancesco@gmail.com> Reviewed-by: NIra Weiny <ira.weiny@intel.com> Link: https://lore.kernel.org/r/20230103173131.21259-1-fmdefrancesco@gmail.comSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Paul Menzel 提交于
Linux logs the error below: $ dmesg --level=err | grep mpt [ 7.647675] mpt3sas_cm0: Trace buffer memory 2048 KB allocated This state does not denote an error condition (and also no warning), so demote the level from error to info. Cc: it+linux-scsi@molgen.mpg.de Signed-off-by: NPaul Menzel <pmenzel@molgen.mpg.de> Link: https://lore.kernel.org/r/20230103150438.45922-1-pmenzel@molgen.mpg.deSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Arnd Bergmann 提交于
Printing a size_t value that is the result of the sizeof() operator requires using the %z format string modifier to avoid a warning on 32-bit architectures: drivers/scsi/qla2xxx/qla_mid.c: In function 'qla_create_buf_pool': drivers/scsi/qla2xxx/qla_mid.c:1094:51: error: format '%ld' expects argument of type 'long int', but argument 5 has type 'unsigned int' [-Werror=format=] 1094 | "Failed to allocate buf_map(%ld).\n", sz * sizeof(unsigned long)); | ~~^ ~~~~~~~~~~~~~~~~~~~~~~~~~~ | | | | long int unsigned int | %d Fixes: 82d8dfd2 ("scsi: qla2xxx: edif: Fix performance dip due to lock contention") Signed-off-by: NArnd Bergmann <arnd@arndb.de> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NHimanshu Madhani <himansnhu.madhani@oracle.com <mailto:himansnhu.madhani@oracle.com>> Reviewed-by: NNick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20230117170029.2387516-1-arnd@kernel.orgSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Alim Akhtar 提交于
Add maintainer entry for Exynos UFS driver. Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230114080247.601312-1-alim.akhtar@samsung.comSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Alim Akhtar 提交于
PA_GRANULARITY is duplicated, delete one of the entries. Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230114022010.27088-1-alim.akhtar@samsung.comSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Kees Cook 提交于
struct MPI2_RAID_SCSI_IO_REQUEST ends with a single SGL, but expects to copy multiple. Add a flexible array member so the compiler can reason about the size of the memcpy(). This will avoid the run-time false positive warning: memcpy: detected field-spanning write (size 128) of single field "&r1_cmd->io_request->SGL" at drivers/scsi/megaraid/megaraid_sas_fusion.c:3326 (size 16) This change results in no binary output differences. Reported-by: NHolger Kiehl <Holger.Kiehl@dwd.de> Link: https://lore.kernel.org/all/88de8faa-56c4-693d-2d3-67152ee72057@diagnostix.dwd.de/ Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Sumit Saxena <sumit.saxena@broadcom.com> Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: megaraidlinux.pdl@broadcom.com Cc: linux-scsi@vger.kernel.org Link: https://lore.kernel.org/r/20230106053153.never.999-kees@kernel.orgSigned-off-by: NKees Cook <keescook@chromium.org> Tested-by: NHolger Kiehl <Holger.Kiehl@dwd.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Martin K. Petersen 提交于
Mike Christie <michael.christie@oracle.com> says: The following patches were made over Martin's scsi-staging/next branch. They add a struct that contains optinal arguments to the scsi_execute* functions. This will be needed for the patches that allow the SCSI passthrough users to control retries because I'm adding a new optional argument. I separated the 2 sets to make it easier to review and post. Link: https://lore.kernel.org/r/20221229190154.7467-1-michael.christie@oracle.comSigned-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute() and scsi_execute_req() are no longer used so remove them. Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute() is going to be removed. Convert cxlflash to use scsi_execute_cmd(). [mkp: roll in fix for issue reported by sfr] Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
- 14 1月, 2023 12 次提交
-
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert pscsi to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert virtio_scsi to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute*() is going to be removed. Convert sr to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert ses to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Conver zbc to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute*() is going to be removed. Convert sd_mod to use scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute() is going to be removed. Convert to the SPI class to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert SCSI midlayer to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute() is going to be removed. Convert the scsi_dh users to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert ch to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert drivetemp to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-
由 Mike Christie 提交于
scsi_execute_req() is going to be removed. Convert libata to scsi_execute_cmd(). Signed-off-by: NMike Christie <michael.christie@oracle.com> Reviewed-by: NJohn Garry <john.g.garry@oracle.com> Reviewed-by: NBart Van Assche <bvanassche@acm.org> Acked-by: NDamien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
-