Since an early commit a few flags have no longer
been used. Remove these definitions to reduce code clutter.

Change-ID: I3589be4622574e747013cd4dc403e18b039f4965
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.

Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We can simply check both Tx and Rx queues in a single loop, rather than
repeating the loop twice.

Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.

Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path.  The previous implementation
set a 'hung bit' which would then get cleared while polling.  If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt.  This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.

Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.

Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously rtnl lock was held during whole reset procedure that
was stopping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.

Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
Signed-off-by: NMaciej Sosin <maciej.sosin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a minor cleanup so that we are always updating pf->flags when we
make a change to the private flags instead of updating a mix of either
pf->flags and/or pf->hw_disabled_flags.

In addition I went through and cleaned out all the spots where we were
using the X722 define in regards to this flag.

Lastly since we changed the logic I went through and flushed out any
redundancy and cleaned up the handling of the flags in the Tx path.

Change-ID: I79ff95a7272bb2533251ff11ef91e89ccb80b610
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Re-word the error message displayed when adding a filter with an
invalid flow type. Additionally, report a distinct error message when
the IPv4 protocol is at fault.

Change-ID: Iba3d85b87f8d383c97c8bdd180df34a6adf3ee67
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The client interface is only intended for use on devices that support
iWarp. Only register with the client if this is the case.

This fixes a panic when loading i40iw on X710 devices.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Reported-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding support for TSO and checksum hardware offloads for ipv6.
Signed-off-by: NThanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sean Wang says:

====================
net-next: dsa: add Mediatek MT7530 support

MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N which includes 7-port
Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY. Among these ports,
The port from 0 to 4 are the user ports connecting with the remote devices
while the port 5 and 6 are the CPU ports connecting into Mediatek Ethernet
GMAC.

The patch series integrated Mediatek MT7530 into DSA support which
includes the most of the essential callbacks such as tag insertion for
port distinguishing, port control, bridge offloading, STP setup and
ethtool operations to allow DSA to model each user port into independently
standalone netdevice as the other DSA driver had done.

Changes since v1:
- rebased into 4.11-rc1
- refined binding document including below five items
- changed the type of mediatek,mcm into bool
- used reset controller binding for MCM reset and removed "mediatek,ethsys"
  property from binding
- reused CPU port's ethernet Phandle instead of creating new one and removed
  "mediatek,ethernet" property from binding
- aligned naming for GPIO reset with dsa/marvell.txt
- added phy-mode as required property child nodes within ports container
- handled gpio reset with devm_gpiod_* API
- refined comment words
- removed condition for CDM setting since the setup looks both fine for all cases
- allowed of_find_net_device_by_node() working with pointing the device node into
  real netdev instance
- fixed Kbuild warnings

Changes since v2:
- reuse readx_poll_timeout() to poll
- add proper macro instead of hard coding
- treat inconsistent cpu port as warning
- remove the usage for regmap-debugfs
- show error message when invalid id is found
- put the logic for the setup of trgmii into adjut_link()
- refine and reuse logic between port_[disable,enable], and default port setup
- correct typo

Changes since v3:
- used struct as the parameter for readx_poll_timeout() and kill
  extra lpriv defined
- moved around function to get out of an additional declaration
- fixed kbuild errors caused by missing proper include in the latest tree
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N platform which
includes 7-port Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY.
Among these ports, The port from 0 to 4 are the user ports connecting
with the remote devices while the port 5 and 6 are the CPU ports
connecting into Mediatek Ethernet GMAC.

For port 6, it can communicate with the CPU via Mediatek Ethernet GMAC
through either the TRGMII or RGMII which could be controlled by phy-mode
in the dt-bindings to specify which mode is preferred to use. And for
port 5, only RGMII can be specified. However, currently, only port 6 is
being supported in this DSA driver.

The driver is made with the reference to qca8k and other existing DSA
driver. The most of the essential callbacks of the DSA are already
support in the driver, including tag insert for user port distinguishing,
port control, bridge offloading, STP setup and ethtool operation to allow
DSA to model each user port into a standalone netdevice as the other DSA
driver had done.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NLanden Chao <Landen.Chao@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the patch adds the setup of the corresponding device node of GMAC into the
netdev instance which could allow other modules such as DSA to find the
instance through the node in dt-bindings using of_find_net_device_by_node()
call.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds the setup for allowing CDM can recognize these packets with
carrying port-distinguishing tag. Otherwise, these tagging packets will be
handled incorrectly by CDM. The setup is also working out for general
untag packets as well.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NLanden Chao <Landen.Chao@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NLanden Chao <Landen.Chao@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add device-tree binding for Mediatek MT7530 switch.

Cc: devicetree@vger.kernel.org
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet_rtm_getroute synthesizes a skeletal ICMP skb, which is passed to
ip_route_input when iif is given. If a multipath route is present for
the designated destination, fib_multipath_hash ends up being called with
that skb. However, as that skb contains no information beyond the
protocol type, the calculated hash does not match the one we would see
for a real packet.

There is currently no way to fix this for layer 4 hashing, as
RTM_GETROUTE doesn't have the necessary information to create layer 4
headers. To fix this for layer 3 hashing, set appropriate saddr/daddrs
in the skb and also change the protocol to UDP to avoid special
treatment for ICMP.
Signed-off-by: NFlorian Larysch <fl@n621.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joao Pinto says:

====================
net: stmmac: adding multiple buffers

This patch adds multiple buffers to stmmac in a more fragmented
way, in order to make problem debug easier.

I would kindly request to people to test this patch in their HWs in
order to check if everything's functional. Thank you.
====================
Tested-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the napi variable to the stmmac_rx_queue
structure and forces that operations like netif_queue_stopped,
netif_wake_queue, netif_stop_queue, netdev_reset_queue and
netdev_sent_queue be made by queue.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the structure stmmac_tx_queue which contains
tx queues specific data (previously in stmmac_priv).
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the structure stmmac_rx_queue which contains
rx queues specific data (previously in stmmac_priv).
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch breaks several functions into RX and TX scopes, which
will be useful when adding multiple buffers mechanism.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tobias Klauser says:

====================
Use net_device_stats from struct net_device

Along the lines of previous patches, switch (almost) all remaining net
drivers to use net_device_stats from net_device instead of including a
copy of it in their netdev_priv struct.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
pegasus, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.

Cc: Petko Manolov <petkan@nucleusys.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
kaweth_device, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.

Cc: linux-usb@vger.kernel.org
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
typhoon, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
de_private, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
happy_meal, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
bigmac, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in
struct w90p910_ether, use stats from struct net_device. Also remove
the now unnecessary .ndo_get_stats function.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
_mace_private, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
moxart_mac_priv_t, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
macb, use stats from struct net_device.

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in
struct emac_instance, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
netdev_private, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function and the #ifdef'ed increment of the
collisions16 counter which doesn't exist in struct net_device_stats.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in
struct port_info, use stats from struct net_device.

Cc: Santosh Raspatur <santosh@chelsio.com>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
port_info, use stats from struct net_device.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qede: support XDP head adjustments

Daniel has brought to my attention the fact that qede is the only driver
that currently supports XDP but still fails any program where
xdp_adjust_head is set on the bpf_prog. This series is meant to remedy
this and align qede with the rest of the driver, making it possible to
remove said field.

Patch #1 contains a minor cache-saving optimization for latter patches.

Patches #2 & #3 address existing issues with the qede implementation
[#2 should have been a part of this as it addresses something that's
affected by the additional headroom; #3 is simply here for the ride].

Patches #4 & #5 add the necessary logic in driver for ingress headroom,
the first adding the infrastrucutre needed for supporting the headroon
[as currently qede doesn't support such], and the second removing the
existing XDP limitation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case an XDP program is attached, reserve XDP_PACKET_HEADROOM
bytes at the beginning of the packet for the program to play
with.

Modify the XDP logic in the driver to fill-in the missing bits
and re-calculate offsets and length after the program has finished
running to properly reflect the current status of the packet.

We can then go and remove the limitation of not supporting XDP programs
where xdp_adjust_head is set.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver currently doesn't support any headroom; The only 'available'
space it has in the head of the buffer is due to the placement
offset.
In order to allow [later] support of XDP adjustment of headroom,
modify the the ingress flow to properly handle a scenario where
the packets would have such.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>