This patch adds support for Telit FN980 0x1050 composition

0x1050: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Add support for Cinterion CLS8 devices.
Use QMI_QUIRK_SET_DTR as required for Qualcomm MDM9x07 chipsets.

T:  Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b0 Rev= 3.18
S:  Manufacturer=GEMALTO
S:  Product=USB Modem
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: NBob Ham <bob.ham@puri.sm>
Signed-off-by: NAngus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRogan Dawes <rogan@dawes.za.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The syzbot reported

 Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  print_address_description+0x67/0x231 mm/kasan/report.c:188
  __kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
  kasan_report+0xe/0x20 mm/kasan/common.c:614
  qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417
  usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454

Caused by too many confusing indirections and casts.
id->driver_info is a pointer stored in a long.  We want the
pointer here, not the address of it.

Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Fixes: e4bf6348 ("qmi_wwan: Add quirk for Quectel dynamic config")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NEnrico Weigelt <info@metux.net>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.

Fixes: c6adf779 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch qmimux_unregister_device() and qmi_wwan_disconnect() to
use unregister_netdevice_queue() and unregister_netdevice_many()
instead of unregister_netdevice(). This avoids RCU stalls which
have been observed on device disconnect in certain setups otherwise.

Fixes: c6adf779 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add proper network device usage statistics for qmimux devices
instead of reporting all-zero values for them.

Fixes: c6adf779 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QMAP code in the qmi_wwan driver is based on the CodeAurora GobiNet
driver which does not process QMAP padding in the RX path correctly.
Add support for QMAP padding to qmimux_rx_fixup() according to the
description of the rmnet driver.

Fixes: c6adf779 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for Telit LE910Cx 0x1260 and 0x1261 compositions.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding device entries found in vendor modified versions of this
driver.  Function maps for some of the devices follow:

WNC D16Q1, D16Q5, D18Q1 LTE CAT3 module (1435:0918)

MI_00 Qualcomm HS-USB Diagnostics
MI_01 Android Debug interface
MI_02 Qualcomm HS-USB Modem
MI_03 Qualcomm Wireless HS-USB Ethernet Adapter
MI_04 Qualcomm Wireless HS-USB Ethernet Adapter
MI_05 Qualcomm Wireless HS-USB Ethernet Adapter
MI_06 USB Mass Storage Device

 T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
 D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
 P:  Vendor=1435 ProdID=0918 Rev= 2.32
 S:  Manufacturer=Android
 S:  Product=Android
 S:  SerialNumber=0123456789ABCDEF
 C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
 E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
 E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
 E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
 E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
 E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
 E:  Ad=88(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
 E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
 E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
 E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

WNC D18 LTE CAT3 module (1435:d182)

MI_00 Qualcomm HS-USB Diagnostics
MI_01 Androd Debug interface
MI_02 Qualcomm HS-USB Modem
MI_03 Qualcomm HS-USB NMEA
MI_04 Qualcomm Wireless HS-USB Ethernet Adapter
MI_05 Qualcomm Wireless HS-USB Ethernet Adapter
MI_06 USB Mass Storage Device

ZM8510/ZM8620/ME3960 (19d2:0396)

MI_00 ZTE Mobile Broadband Diagnostics Port
MI_01 ZTE Mobile Broadband AT Port
MI_02 ZTE Mobile Broadband Modem
MI_03 ZTE Mobile Broadband NDIS Port (qmi_wwan)
MI_04 ZTE Mobile Broadband ADB Port

ME3620_X (19d2:1432)

MI_00 ZTE Diagnostics Device
MI_01 ZTE UI AT Interface
MI_02 ZTE Modem Device
MI_03 ZTE Mobile Broadband Network Adapter
MI_04 ZTE Composite ADB Interface
Reported-by: NLars Melin <larsm17@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most, if not all, Quectel devices use dynamic interface numbers, and
users are able to change the USB configuration at will. Matching on for
example interface number is therefore not possible.

Instead, the QMI device can be identified by looking at the interface
class, subclass and protocol (all 0xff), as well as the number of
endpoints. The reason we need to look at the number of endpoints, is
that the diagnostic port interface has the same class, subclass and
protocol as QMI. However, the diagnostic port only has two endpoints,
while QMI has three.

Until now, we have identified the QMI device by combining a match on
class, subclass and protocol, with a call to the function
quectel_diag_detect(). In quectel_diag_detect(), we check if the number
of endpoints matches for known Quectel vendor/product ids.

Adding new vendor/product ids to quectel_diag_detect() is not a good
long-term solution. This commit replaces the function with a quirk, and
applies the quirk to affected Quectel devices that I have been able to
test the change with (EP06, EM12 and EC25). If the quirk is set and the
number of endpoints equal two, we return from qmi_wwan_probe() with
-ENODEV.
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a Qualcomm based device with a QMI function on interface 4.
It is mode switched from 2020:2030 using a standard eject message.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2031 Rev= 2.32
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quectel EG12 (module)/EM12 (M.2 card) is a Cat. 12 LTE modem. The modem
behaves in the same way as the EP06, so the "set DTR"-quirk must be
applied and the diagnostic-interface check performed. Since the
diagnostic-check now applies to more modems, I have renamed the function
from quectel_ep06_diag_detected() to quectel_diag_detected().
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 1199:68C0 USB ID is reused by Sierra WP7607 which requires the DTR
quirk to be detected. Apply QMI_QUIRK_SET_DTR unconditionally as
already done for other IDs shared between different devices.
Signed-off-by: NBeniamino Galvani <bgalvani@redhat.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds MTU default value to qmap network interface in
order to avoid "RTNETLINK answers: No buffer space available"
error when setting an ipv6 address.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes qmap header retrieval when modem is configured for
dl data aggregation.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for Fibocom NL678 series cellular module QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x40 series chipsets.
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: NGiacinto Cifelli <gciofono@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host.  The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk.  This method fails when the modems are forced to
USB2 mode by the modem firmware.

Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: NFred Veldini <fred.veldini@gmail.com>
Reported-by: NDeshu Wen <dwen@sierrawireless.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Reported-by: NFred Veldini <fred.veldini@gmail.com>
Reported-by: NDeshu Wen <dwen@sierrawireless.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quectel EP06 (and EM06/EG06) supports dynamic configuration of USB
interfaces, without the device changing VID/PID or configuration number.
When the configuration is updated and interfaces are added/removed, the
interface numbers change. This means that the current code for matching
EP06 does not work.

This patch removes the current EP06 interface number match, and replaces
it with a match on class, subclass and protocol. Unfortunately, matching
on those three alone is not enough, as the diag interface exports the
same values as QMI. The other serial interfaces + adb export different
values and do not match.

The diag interface only has two endpoints, while the QMI interface has
three. I have therefore added a check for number of interfaces, and we
ignore the interface if the number of endpoints equals two.
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Fixes: e7e197ed ("qmi_wwan: add support for the Dell Wireless 5821e module")
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: NMatevz Vucnik <vucnikm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.

By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Netgear Aircard 779S
Signed-off-by: NJosh Hill <josh@joshuajhill.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function.  The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.

Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID.  This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a77 ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")

Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: NSebastian Sjoholm <sebastian.sjoholm@gmail.com>
Cc: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The USB_DEVICE_INTERFACE_NUMBER matching macro assumes that
the { vendorid, productid, interfacenumber } set uniquely
identifies one specific function.  This has proven to fail
for some configurable devices. One example is the Quectel
EM06/EP06 where the same interface number can be either
QMI or MBIM, without the device ID changing either.

Fix by requiring the vendor-specific class for interface number
based matching.  Functions of other classes can and should use
class based matching instead.

Fixes: 03304bcb ("net: qmi_wwan: use fixed interface number matching")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for PID 0x90b2 of ublox R410M.

qmicli -d /dev/cdc-wdm0 --dms-get-manufacturer
[/dev/cdc-wdm0] Device manufacturer retrieved:
        Manufacturer: 'u-blox'

qmicli -d /dev/cdc-wdm0 --dms-get-model
[/dev/cdc-wdm0] Device model retrieved:
        Model: 'SARA-R410M-02B'
Signed-off-by: NSZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This modem is embedded on dlink dwr-960 router.
The oem configuration states:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution
Signed-off-by: NPawel Dembicki <paweldembicki@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This modem is embedded on dlink dwr-921 router.
    The oem configuration states:

    T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
    D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1435 ProdID=0918 Rev= 2.32
    S:  Manufacturer=Android
    S:  Product=Android
    S:  SerialNumber=0123456789ABCDEF
    C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
    I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
    E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
    E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
    E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=88(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
    E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution
Signed-off-by: NGiuseppe Lippolis <giu.lippolis@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to support the modem found in HP EliteBook 820 G3.
Signed-off-by: NTorsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
The USB id is added to qmi_wwan.c to allow QMI communication with
the BM806U.

Tested on 4.14 kernel and OpenWRT.
Signed-off-by: NPawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Quectel EP06 is a Cat. 6 LTE modem. It uses the same interface as
the EC20/EC25 for QMI, and requires the same "set DTR"-quirk to work.
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for PID 0x9625 of YUGA CLM920-NC5.

YUGA CLM920-NC5 needs to enable QMI_WWAN_QUIRK_DTR before QMI operation.

qmicli -d /dev/cdc-wdm0 -p --dms-get-revision
[/dev/cdc-wdm0] Device revision retrieved:
        Revision: 'CLM920_NC5-V1  1  [Oct 23 2016 19:00:00]'
Signed-off-by: NSZ Lin (林上智) <sz.lin@moxa.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It has been reported that the dummy byte we add to avoid
ZLPs can be forwarded by the modem to the PGW/GGSN, and that
some operators will drop the connection if this happens.

In theory, QMI devices are based on CDC ECM and should as such
both support ZLPs and silently ignore the dummy byte.  The latter
assumption failed.  Let's test out the first.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Telit ME910 PID 0x1101.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: NSebastian Sjoholm <ssjoholm@mac.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>