This increases the chances we'll manage to hit a partially configured
state on restart and the power savings are extremely small.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for spi regmap feature to existing da7210
driver.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

No current users and it's the last user of MICBIAS_E().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Acked-by: NZeng Zhaoming <zengzm.kernel@gmail.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>

Rather than trying to work around machine drivers which try to reprogram
the FLL while it is providing SYSCLK just return an error if they try.
This will avoid audio glitches during FLL reconfiguration, or at least
move the introduction of the glitches to the machine driver.

Since disabling the source for an active SYSCLK is not supported in the
first place systems shouldn't be doing this in the first place.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
 requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It's possible that the regulator enable will fail and if it does we may
as well just give up with trying to bring the rest of the device up and
report the original error.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTimur Tabi <timur@freescale.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We can simply use the register cache code to synchronise the current
configuration down to the device when bringing up the DSP.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This change adds the logic to support using the jack detect mechanism built
in to the codec to detect both when a jack was inserted and what type of
jack is present.

This change also supports the use of an external mechanism for headphone
detection. If this mechanism exists, when the max98095_jack_detect function
is called, the hp_jack is simply passed NULL.

This change supports both simple headphones, powered headphones, microphones
and headsets with both headphones and a mic.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

DAPM now has a DAPM-level lock which it manages itself so we don't need
to take the CODEC mutex to call DAPM any more.  Also remove a redundant
call to snd_soc_dapm_sync(), jack reporting also triggers a DAPM sync.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It's more idiomatic to do this and it means we don't try to bring up the
card if the CODEC didn't manage to bind successfully.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Based on latest production information.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The optimal management of VMID depends on a number of factors which vary
dynamically at runtime, for example the connection to a system docking
station. In some circumstances it is desirable to keep VMID enabled all
the time, in others it is desirable to aggressively power it up and down.

Provide a callback allowing machine driver to configure either the normal
power up/down mode (WM8994_VMID_MODE_NORMAL) or to maintain VMID even
when idle (WM8994_VMID_MODE_FORCE). This callback, wm8994_vmid_mode(),
should be called with the CODEC lock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It can just be enabled all the time with no impact.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8996 specification has been updated to specify 44.1kHz as a supported
sample rate. Update the driver to accept this configuration.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently we can the accdet mutex from within DAPM when updating the device
state which means we take accdet then the CODEC mutex but we also do the
locking the other way around when responding to the jackdet IRQ. Move all
the jackdet use of the CODEC mutex out of the accdet lock to avoid this.
Since all the DAPM interactions depend only on a single threaded IRQ this
is still serialised.

The locking improvements in 3.5 allow a better solution there.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch removes following registers from reg map defaults,

- Registers which are currently not used by driver
- Non existing registers
- Volatile registers
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Marginally improve performance during startup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current DA7210 driver has I2C support using older register cache
methods. This patch updates it for latest regmap framework.

This has been tested on DA7210 EVB with Samsung SMDK6410 board.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit 891271c2 "ASoC: Convert wm8804 to direct regmap API usage"
only converts wm8804_spi_probe to use regmap_init_spi.

This patch adds missing regmap_init_i2c in wm8804_i2c_probe.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Save a little RAM.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The default pm_runtime status is enabled which is what we want.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When we are out of system sleep always use audio mode for jack detection
in order to avoid potential performance issues handing off between modes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Without that fix the wm8753 SPI initialization fails, and then produces
  a kernel panic during boot with the following call trace:
    Unable to handle kernel paging request at virtual address 37386d9b
    [<c01ccafc>] (regmap_get_val_bytes+0x0/0x14) from [<c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc)
    [<c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc) from [<c0244a4c>] (wm8753_probe+0x5c/0x1c4)
    [<c0244a4c>] (wm8753_probe+0x5c/0x1c4) from [<c023bb24>] (soc_probe_codec+0x174/0x284)
    [<c023bb24>] (soc_probe_codec+0x174/0x284) from [<c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28)
    [<c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28) from [<c023d278>] (snd_soc_register_card+0x240/0x2d4)
    [<c023d278>] (snd_soc_register_card+0x240/0x2d4) from [<c023d330>] (soc_probe+0x24/0x40)
    [<c023d330>] (soc_probe+0x24/0x40) from [<c01c3900>] (platform_drv_probe+0x14/0x18)
    [...]

The commit d3398ff0
 ( ASoC: Convert WM8753 to direct regmap API usage ) introduced
 the problem.

Thanks to Lars-Peter Clausen for helping me a bit during the debugging.
Signed-off-by: NDenis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Push everything through one function for active use cases, should be
no practical effect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If we're not doing jackdet it's not needed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Normally this will have no effect as we set detection up at system startup
before DAPM syncs take effect, this will only be useful if the system
enables and disables detection at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Using snd_soc_write() means we always write to the register even if it
already contains the newly calculated value.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Class W mode with sidetone is not fully supported.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>