There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
   and install them again, must use "ifconfig down/ifconfig up"
   command pair to bring port to work.

   This patch calls phy_stop function when init phy to fix this bug.

2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
   all ports can not use anymore, because of the phy devices register
   failed(phy devices already exists).

   Phy devices are registered when hns_dsaf installed, this patch
   removes them when hns_dsaf removed.

The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:

WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init

Remove the __init to make it always do the right thing.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All previous docks and dongles that have supported this feature use
the RTL8153-AD chip.

RTL8153-BND is a new chip that will be used in upcoming Dell type-C docks.
It should be added to the whitelist of devices to activate MAC address
pass through.

Per confirming with Realtek all devices containing RTL8153-BND should
activate MAC pass through and there won't use pass through bit on efuse
like in RTL8153-AD.
Signed-off-by: NMario Limonciello <mario.limonciello@dell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

recalculated send and receive window using linkspeed.
Determine correct value of eck_ok from SYN received and
option configured on local system.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

corrected macro used in tx path. removed redundant hdrlen
and check for !page in chtls_sendmsg
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

listen fails when more than one tls capable device is
registered. tls_hw_hash is called for each dev which loops
again for each cdev_list causing listen failure. Hence
call chtls_listen_start/stop for specific device than loop over all
devices.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW unhash within mutex for registered tls devices cause sleep
when called from tcp_set_state for TCP_CLOSE. Release lock and
re-acquire after function call with ref count incr/dec.
defined kref and fp release for tls_device to ensure device
is not released outside lock.

BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:748
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/7
INFO: lockdep is turned off.
CPU: 7 PID: 0 Comm: swapper/7 Tainted: G        W  O
Call Trace:
 <IRQ>
 dump_stack+0x5e/0x8b
 ___might_sleep+0x222/0x260
 __mutex_lock+0x5c/0xa50
 ? vprintk_emit+0x1f3/0x440
 ? kmem_cache_free+0x22d/0x2a0
 ? tls_hw_unhash+0x2f/0x80
 ? printk+0x52/0x6e
 ? tls_hw_unhash+0x2f/0x80
 tls_hw_unhash+0x2f/0x80
 tcp_set_state+0x5f/0x180
 tcp_done+0x2e/0xe0
 tcp_rcv_state_process+0x92c/0xdd3
 ? lock_acquire+0xf5/0x1f0
 ? tcp_v4_rcv+0xa7c/0xbe0
 ? tcp_v4_do_rcv+0x70/0x1e0
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns:

drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
                                   ^
1 warning generated.

Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.

Fixes: cac6f691 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TXQ SQ closure is followed by closing the corresponding CQ. A pending
DIM work would try to modify the now non-existing CQ.
This would trigger an error:
[85535.835926] mlx5_core 0000:af:00.0: mlx5_cmd_check:769:(pid 124399):
MODIFY_CQ(0x403) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1d7771)

Fix by making sure to cancel any pending DIM work before destroying the SQ.

Fixes: cbce4f44 ("net/mlx5e: Enable adaptive-TX moderation")
Signed-off-by: NTal Gilboa <talgi@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Remove tx_udp_seg_rem counter from ethtool output, as it is no longer
being updated in the driver's data flow.

Fixes: 3f44899e ("net/mlx5e: Use PARTIAL_GSO for UDP segmentation")
Signed-off-by: NMikhael Goikhman <migo@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, we are deleting offloaded encap flows in case the relevant neigh
becomes unconnected while the encap is valid (a sign that it used to be
connected), or if the curr neigh mac is different from the cached mac
(a sign that the remote side changed their mac).

The 2nd check also applies when the neigh becomes connected on the 1st
time (we start with zero mac). Before the offending commit, the deleting
handler was practically no op, as no flows were offloaded. But since
that commit, we offload neigh-less encap flows to slow path.

Under mirroring scheme, we go into the delete handler, attempt to unoffload a
mirror rule which was never set (as we were offloading to slow path) and crash.

Fix that by calling the delete handler only when the encap is valid,
which covers both cases mentioned above.

Fixes: 5dbe906f ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NEli Britstein <elibr@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When a neighbour is resolved, we delete the goto slow path rule from HW.

The eswitch flow attributes where not properly initialized on that case,
hence we mess up the eswitch refcounts for chain zero (the default one).

Fix that along with making sure to use semicolons and not commas on that code;

Fixes: 5dbe906f ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Just a leftover which was wrongly left there, remove it while spawning
a message to suggest firmware upgrade.

Fixes: bf07aa73 ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently we are not supporting this and not err-ing on that either.

For now, just err if asked to do that.

Fixes: bf07aa73 ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NEli Britstein <elibr@mellanox.com>
Reviewed-by: NEli Britstein <elibr@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add check of MPWQE stride size is within range supported by HW. In case
calculated MPWQE stride size exceed range, linear SKB can't be used and
we should use non linear MPWQE instead.

Fixes: 619a8f2a ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The default amount of channels a representor opens was erroneously
changed from one to the maximum amount of channels, restore to its
intended value.

Fixes: 779d986d ("net/mlx5e: Do not ignore netdevice TX/RX queues number")
Signed-off-by: NGavi Teitz <gavi@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This reverts commit 78139c94. We don't
protect device IOTLB with vq mutex, which will lead e.g use after free
for device IOTLB entries. And since we've switched to use
mutex_trylock() in previous patch, it's safe to revert it without
having deadlock.

Fixes: commit 78139c94 ("net: vhost: lock the vqs one by one")
Cc: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to hold the mutex of paired virtqueue in
vhost_net_busy_poll(). But this will results an inconsistent lock
order which may cause deadlock if we try to bring back the protection
of device IOTLB with vq mutex that requires to hold mutex of all
virtqueues at the same time.

Fix this simply by switching to use mutex_trylock(), when fail just
skip the busy polling. This can happen when device IOTLB is under
updating which should be rare.

Fixes: commit 78139c94 ("net: vhost: lock the vqs one by one")
Cc: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We miss a write barrier that guarantees used idx is updated and seen
before log. This will let userspace sync and copy used ring before
used idx is update. Fix this by adding a barrier before log_write().

Fixes: 8dd014ad ("vhost-net: mergeable buffers support")
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There will be only one PHC clock per port. PTP should be enabled only on
one PF per port. The change enables PTP functionality on the PF that
initializes the port. The change is useful in multi-function modes e.g.,
NPAR where a port can have more than one PF.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.

Fixes: 939b701a ("ixgbe: fix driver behaviour after issuing VFLR")
Signed-off-by: NRoss Lagerwall <ross.lagerwall@citrix.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move rx_ptype extracting to i40e_process_skb_fields() to avoid
duplicating the code.
Signed-off-by: NMichał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.

Add a length check for both locations and updated hso_probe to bail on
error.

This issue has been assigned CVE-2018-19985.
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: NHui Peng <benquike@gmail.com>
Signed-off-by: NMathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes two bugs in hardware VLAN offload:
 1. VLAN.TCI == 0 was being dropped
 2. there was a race between disabling of VLAN RX feature in hardware
    and processing RX queue, where packets processed in this window
    could have their VLAN information dropped

Fix moves the VLAN handling into i40e_process_skb_fields() to save on
duplicated code. i40e_receive_skb() becomes trivial and so is removed.
Signed-off-by: NMichał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().

Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.

Fixes: 458867b2 ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.

Fixes: 38caff5a ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc warning this:

drivers/net/ieee802154/ca8210.c:730:10: warning:
 comparison is always false due to limited range of data type [-Wtype-limits]

'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.

Fixes: ded845a7 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>

Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.

Fixes: 07e1671c ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ibmvnic_reset allocated new reset work item objects in a non-atomic
context. This can be called from a tasklet, generating the output below.
Allocate work items with the GFP_ATOMIC flag instead.

BUG: sleeping function called from invalid context at mm/slab.h:421
in_atomic(): 1, irqs_disabled(): 1, pid: 93, name: kworker/0:2
INFO: lockdep is turned off.
irq event stamp: 66049
hardirqs last  enabled at (66048): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (66049): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last  enabled at (66044): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (66045): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 0 PID: 93 Comm: kworker/0:2 Kdump: loaded Not tainted 4.20.0-rc6-00001-g1b50a8f03706 #7
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffe7ae0] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffe7b30] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffe7bb0] [c000000000391514] kmem_cache_alloc_trace+0x3e4/0x440
[c0000003fffe7c30] [d000000005b2309c] ibmvnic_reset+0x16c/0x360 [ibmvnic]
[c0000003fffe7cc0] [d000000005b29834] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffe7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffe7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffe7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3967980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f39679c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f39679f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3967a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3967a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3967ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3967b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3967ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3967bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3967c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3967c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3967d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3967db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3967e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ibmvnic_reset can create and schedule a reset work item from
an IRQ context, so do not use a mutex, which can sleep. Convert
the reset work item mutex to a spin lock. Locking debugger generated
the trace output below.

BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
in_atomic(): 1, irqs_disabled(): 1, pid: 120, name: kworker/8:1
4 locks held by kworker/8:1/120:
 #0: 0000000017c05720 ((wq_completion)"events"){+.+.}, at: process_one_work+0x188/0x710
 #1: 00000000ace90706 ((linkwatch_work).work){+.+.}, at: process_one_work+0x188/0x710
 #2: 000000007632871f (rtnl_mutex){+.+.}, at: rtnl_lock+0x30/0x50
 #3: 00000000fc36813a (&(&crq->lock)->rlock){..-.}, at: ibmvnic_tasklet+0x88/0x2010 [ibmvnic]
irq event stamp: 26293
hardirqs last  enabled at (26292): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (26293): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last  enabled at (26288): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (26289): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 8 PID: 120 Comm: kworker/8:1 Kdump: loaded Not tainted 4.20.0-rc6 #6
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffa7a50] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffa7aa0] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffa7b20] [c000000000be960c] __mutex_lock+0x8c/0xb40
[c0000003fffa7c30] [d000000006202ac8] ibmvnic_reset+0x78/0x330 [ibmvnic]
[c0000003fffa7cc0] [d0000000062097f4] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffa7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffa7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffa7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3f87980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f3f879c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f3f879f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3f87a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3f87a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3f87ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3f87b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3f87ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3f87bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3f87c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3f87c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3f87d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3f87db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3f87e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CP rings are accounted differently on the new 57500 chips.  There
must be enough CP rings for the sum of RX and TX rings on the new
chips.  The current logic may be over-estimating the RX and TX rings.

The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips.  We need to introduce a new
bnxt_nq_rings_in_use().  On legacy chips, the 2 functions are the
same and one will just call the other.  On the new chips, they
refer to the 2 separate ring structures.  The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.

On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.

Fixes: 41e8d798 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector.  To better unify this, add a resv_irqs
field to struct bnxt_hw_resc.  On legacy chips, we initialize resv_irqs
with resv_cp_rings.  On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>